Multiphase models of flotation machine behaviour

Models in which the cell contents are partitioned into distinct pulp and froth phases are reviewed critically. The nature of the mixing within the phases is discussed. Multiphase models describing froth column concentration gradients and pulp residence time effects are mentioned. It is shown that at steady state multiphase models can be reduced to the two-phase case. Deficiencies in the models and topics requiring further development are outlined.     

The effect of petroleum hydrocarbons on reproduction of an estuarine planktonic copepod in laboratory cultures

The effect of short-term exposure to high concentration (mg l.^?1) of water soluble fraction of aromatic heating oil on subsequent egg production by the estuarine copepod Eurytemora affinis has been studied in laboratory cultures to investigate possibly sublethal biological effects following exposure to hydrocarbon under an oil spill. Significant reduction in subsequent length of life, total number of eggs produced, mean brood size, and rate of egg production was observed. Exposure to naphthalene alone at 1 mg l.^?1 for 24 h produced a significant effect on total fecundity of the females. Ingestion rates were significantly lower when measured in the presence of the water soluble fraction, and also naphthalene alone at mg l.^?1 concentrations. Exposure to low-levels (10 and 50 μg l.^?1) of ¹⁴C-naphthalene alone over a period of ten days produced no significant effect on feeding or reproduction despite the high concentrations of hydrocarbon accumulated during this period. The results are discussed in relation to previous work on the fate of hydrocarbons in planktonic copepods, using ¹⁴C-1-naphthalene as a model compound.     

The air flow number in flotation machine scale-up

The flotation cell is quantified as a mixing device for one, two, and three phase systems using combinations of water, air, and solids. To do this, power consumption was measured as a function of impeller speed, rate of aeration, and solids concentration. Initial suspension of solids and dispersion of suspended solids throughout the water or water/air system were also studied as influenced by impeller speed, particle size and solids concentration. The power number and air flow number were used to correlate the data.Flotation studies with a zinc ore using three sizes of cells of the same design, showed that aeration had to be controlled in the smaller cells to duplicate the results in the cell of commercial size. For optimum results the flow number range in the smallest cell was less than the critical value for suspension of coarse particles. Operating flow numbers for the three cell sizes under optimum conditions were close; commercial cells of the same size operating elsewhere appear to have two to three times higher flow numbers.The general relationships among air flow, impeller speed, particle suspension and flotation are discussed with particular reference to scale-up problems and coarse particle flotation. Both impeller speed and aeration should be considered as variables requiring systematic study and independent adjustment.     

Interactions between sulphide minerals and xanthates,I. The formation of monothiocarbonate at galena and pyrite surfaces

The rate of decomposition of potassium ethyl monothiocarbonate has been determined at pH values between 5 and 10, and its molar absorptivity at 221 nm determined to be 1.24 · 10⁴mol/cm.A novel apparatus for use in the study of reactions between sulphide minerals, oxygen and thiol reagents has been developed, and applied to the reactions of potassium ethyl xanthate with galena and pyrite. It has been shown that both minerals react with ethyl xanthate in the presence of oxygen or oxidation products to form soluble as well as adsorbed xanthate derivatives. The soluble derivative has been identified to be ethyl monothiocarbonate. The adsorbed xanthate at a galena surface, unlike that at a pyrite surface, is gradually converted to a soluble monothiocarbonate under the action of dissolved oxygen. The effect of variables such as pH, the initial xanthate and oxygen concentrations, and the initial state of oxidation of the mineral on the formation of monothiocarbonate has been studied. It is tentatively proposed that an intermediate adsorbed mixed xanthate-hydroxide species is involved in the formation of monothiocarbonate at both galena and pyrite surfaces.The significance of the formation of monothiocarbonate to flotation practice is discussed briefly. The formation of monothiocarbonate represents a wastage of reagent, and could lead to a decrease in flotability of xanthated galena with time of exposure to aerated solutions.     

Heavy metals in organic phases of river and estuarine sediment

Analysis of sediments taken from various levels in the lightly polluted River Blyth in Northumberland shows that quite high concentrations of metals can be accumulated in sediments.     

Delineation of intrinsic geological units

Conventional methods for the estimation of mineral resources potential are broadly subdivided into two groups: subjective models based upon ore genetic theories and objective models based upon multiple geological observations. This paper examines some objective means that brings the two types of model together and jointly utilizes the information from both ore genesis and geological observations in delineation of promising areas for mineral exploration. These promising areas are here referred to as intrinsic geological units. They are so-called because they are not identified directly with respect to mineral deposits, but delineated in terms of some critical genetic factor, a necessary condition for formation of the mineral deposits. Four major steps are involved in this analysis. First, establish the structure of critical genetic factor-recognition criteria-multiple geodata for the deposit type of interest. Next, estimate probabilities of occurrence of each of the recognition criteria based upon geological observations. Third, a synthesized probability measure for occurrence of critical genetic factor is determined as an optimum linear combination of the probabilities estimated in the second stage. Finally, intrinsic geological units are delineated by optimally discretizing the probability measure for the critical genetic factor. This estimation procedure is formulated into a three-stage optimization model: logistic regression-quadratic programming-optimum discretization, which is demonstrated with a case study on epithermal Au-Ag mineral deposits in the Walker Lake quadrangle of California and Nevada. In this case study, heat source is selected as the critical genetic factor and it is identified by three selected recognition criteria: Au-Ag mineral occurrence, Tertiary intrusive, and hydrothermal alteration. The intrinsic geological units for epithermal Au-Ag deposits are delineated on the basis of six different preprocessed and integrated geological, geochemical, and geophysical fields.     

Post-mining deterioration of bauxite overburdens in Jamaica: storage methods or subsoil dilution?

Rapid degradation of disturbed soil from a karst bauxite mine in Jamaica was recorded. Substantial macronutrient losses were incurred during a short (1 month) or a long (12 months) storage of the replaced topsoils during frequent wet/dry changes. The results suggested very high rates (>70% in the first year) of soil degradation from storage, alongside moderate rates (30%) within the same storage dump. However, higher levels of soil organic matter (SOM) were indicated just below the surface, compared with the surface horizons. It was unlikely that under a high leaching humid tropical rainfall regime, natural degradation processes could have re-emplaced such material firmly intact in the 15–30 cm zone. It was therefore concluded that these SOM anomalies were due to mechanical dilution of surface soil with subsoil material during overburden removal and emplacement rather than from long storage. Increasing the soil organic content during storage could be one corrective approach. However, it is far less costly to exercise greater care to apply more precise overburden removal and emplacement techniques initially, than it is to correct the results of topsoil contamination with subsoil. Although this study was limited to one mine, in the context of imminent large-scale mining expansion and current practices, further investigations are needed to accurately ascertain the proportion of similar subsoil contamination in other bauxite-mined sites.     

Geographically weighted methods and their use in network re-designs for environmental monitoring

Given an initial spatial sampling campaign, it is often of importance to conduct a second, more targeted campaign based on the properties of the first. Here a network re-design modifies the first one by adding and/or removing sites so that maximum information is preserved. Commonly, this optimisation is constrained by limited sampling funds and a reduced sample network is sought. To this extent, we demonstrate the use of geographically weighted methods combined with a location-allocation algorithm, as a means to design a second-phase sampling campaign in univariate, bivariate and multivariate contexts. As a case study, we use a freshwater chemistry data set covering much of Great Britain. Applying the two-stage procedure enables the optimal identification of a pre-specified number of sites, providing maximum spatial and univariate/bivariate/multivariate water chemistry information for the second campaign. Network re-designs that account for the buffering capacity of a freshwater site to acidification are also conducted. To complement the use of basic methods, robust alternatives are used to reduce the effect of anomalous observations on the re-designs. Our non-stationary re-design framework is general and provides a relatively simple and a viable alternative to geostatistical re-design procedures that are commonly adopted. Particularly in the multivariate case, it represents an important methodological advance.     

GPU accelerated radio astronomy signal convolution

The increasing array size of radio astronomy interferometers is causing the associated computation to scale quadratically with the number of array signals. Consequently, efficient usage of alternate processing architectures should be explored in order to meet this computational challenge. Affordable parallel processors have been made available to the general scientific community in the form of the commodity graphics card. This work investigates the use of the Graphics Processing Unit in the parallelisation of the combined conjugate multiply and accumulation stage of a correlator for a radio astronomy array. Using NVIDIA’s Compute Unified Device Architecture, our testing shows processing speeds from one to two orders of magnitude faster than a Central Processing Unit approach.