Interactive behavior of soil–pile-superstructure system in transient state to liquefaction by means of large shake table tests

Shaking table tests were conducted by means of a large-scale laminar box with 4 m in length, 2 m in width and 2 m in height in order to investigate behavior of a soil-pile-superstructure system in liquefiable ground. A model two-storey structure, supported by a pile group, was set in a saturated sand deposit, and subjected to a sinusoidal base motion with increasing amplitude. Discussions are focused on the transient behavior until soil liquefaction occurs. Main interests are characteristics of springs used in a sway-rocking model and a multi-freedom lumped mass (MFLM) model that are frequently used in soil–pile interaction analysis. The spring constant in the sway-rocking model is represented by restoring force characteristics at the pile head, and that in the MFLM system is represented by an interaction spring connecting the pile to the free field. The transient state prior to soil liquefaction is shown to be important in the design of a pile because dynamic earth pressure shows peak response in this state. The reduction of the stiffness due to excess porewater generation and strain dependent nonlinear behavior is evaluated.     

MHD Dynamo Simulation Using the GeoFEM Platform: Comparison with a Spectral Method

— We investigate differences of results of a MHD dynamo simulation using the finite-element method (FEM) with that by the spherical harmonics expansion. The simulation was performed with a total of 7.8×10⁴ elements in the simulation domain. The results show that the magnetic energy is generated approximately four times of the kinetic energy in both cases. The outline of present results has consistence with that by the spectral method. However, small-scale patterns can be observed in the spectral method case. These discrepancies are caused by limitation of the spatial resolution in both of the present simulations.     

From an initial transient-state to a steady-state in metamorphic reactions: An experimental approach in the system dolomite-quartz-H2O

Abstract We carried out hydrothermal experiments in the system dolomite‐quartz‐H₂O to track the temporal change in reaction rates of simultaneous reactions during the development of reaction zones. Two types of configurations for the starting materials were prepared: dolomite single crystals + quartz powder + water and quartz single crystals + dolomite powder + water, both sealed separately in gold capsules. Runs at 0.1GPa and 600°C with cold seal pressure vessels gave the following results. (i) In short duration (45–71 h) runs metastable layer sequences involving wollastonite and talc occur in the reaction zone, whereas they disappear in longer duration (168–336 h) runs. (ii) The layer sequence of the reaction zones in short duration runs differs from place to place on the dolomite crystal even in the same run. (iii) The diversity of layer sequences in the short duration runs merges into a unique layer sequence in the longer duration runs. (iv) The reaction zone develops locally on the dolomite crystal, but no reaction zone was observed on the quartz crystal in any of the runs. The lines of evidence (i)–(iii) show that the system evolves from an initial transient‐ to a steady‐state and that the kinetic effect is important in the development of reaction zones. A steady diffusion model for the unique layer sequence Qtz/Di/Fo + Cal/Dol + Cal/Dol shows that the Dol + Cal layer cannot be formed by diffusion‐controlled process and that the stability of the layer sequence Qtz/Di/Fo + Cal/Dol depends not only on L‐ratios (a = /L_CaOCaO and b = /L_MgOMgO) but also on the relative rate P = (−2ξ₁ − ξ₂)/(–ξ₁ − 2ξ₂) of competing reactions: Dol + 2Qtz = Di + 2CO₂ (ξ₁) and 2Dol + Qtz = Fo + 2Cal + 2CO₂ (ξ₂). For smaller P the stability field will shift to higher values of a and b. The steady diffusion model also shows that the apparent‐non‐reactivity on the quartz surface can be attributed to void formation in a large volume fraction in the diopside layer.     

Wave energy in surface layers for energy-based damage evaluation

Seismic wave energy in surface layers is calculated based on vertical array records at four sites during the 1995 Hyogo-ken Nambu earthquake by assuming vertical propagation of SH waves. The upward energy generally tends to decrease as it goes up from the base layer to the ground surface particularly in soft soil sites. Theoretical study on 1D multi-layers model to investigate the basic energy flow mechanism indicates that the energy at the ground surface can be smaller on softer soils due to high soil damping during strong shaking even if resonance effect is considered. A simple calculation for a shear-vibrating structure resting on foundation ground shows that induced strain in the structure is directly related to the energy or the energy flux of surface layers. Hence, a general perception that soft soil sites tend to suffer heavier damage than stiff sites should be explained not by greater incident energy but by other reasons such as degree of resonance. Furthermore, it is recommended that not only acceleration or velocity but also S-wave velocity should be specified at a layer where a design seismic motion is given, so that the seismic wave energy can clearly be quantified in seismic design practice.     

Seismic response of steel structures with seesaw systems using viscoelastic dampers

Vibration control systems are being used increasingly worldwide to provide enhanced seismic protection for new and retrofitted buildings. This paper presents a new vibration control system on the basis of a seesaw mechanism with viscoelastic dampers. The proposed vibration control system comprises three parts: brace, seesaw member, and viscoelastic dampers. In this system, only tensile force appears in bracing members. Consequently, the brace buckling problem is negligible, which enables the use of steel rods for bracing members. By introducing pre‐tension in rods, long steel rods are applicable as bracing between the seesaw members and the moment frame connections over some stories. Seesaw mechanisms can magnify the damper deformation according to the damper system configuration. In this paper, first, the magnification factor, that is, the ratio of the damper deformation to the story drift, is delivered, which includes the rod deformation. Results of a case study demonstrate that the magnification factor of the proposed system is greater than unity for some cases. Seismic response analysis is conducted for steel moment frames with the proposed vibration control system. Energy dissipation characteristics are examined using the time‐history response results of energy. The maximum story drift angle distributions and time‐history response results of displacement show that the proposed system can reduce the seismic response of the frames effectively. Copyright © 2012 John Wiley & Sons, Ltd.     

Finite element analysis and experimental verification of the scrap tire rubber pad isolator

A new base isolation system using scrap tire rubber pads (STRP) has been introduced for seismic mitigation of ordinary residential buildings. The rubber and the steel reinforcing cords used in manufacturing the tire are the alternative materials of the proposed base isolation system. The steel reinforcing cords represent the steel plates used in conventional laminated rubber bearings. These steel reinforcing cords shall prevent the lateral bulging of the rubber bearing. The proposed base isolation system has no bonding between the superstructure and the foundation beam which allows for rollover deformation. In the first part of the study, the STRP layers were just stacked one on top of another without applying the adhesive. This paper presents loading test as well as finite element analysis (FE analysis) of strip STRP isolators that are subjected to any given combination of static vertical and lateral loads. The results of the static vertical and horizontal loading test conducted on STRP isolators were used to calculate the mechanical properties of the isolators, including stiffness and damping values. The load–displacement relationship of STRP isolators were compared between experimental and FE analysis results and the results were found to be in close agreement. The stress state within the STRP isolators was also analyzed in order to estimate the maximum stress demand in the rubber and steel reinforcing cords. These STRP isolators have several advantages over conventional laminated rubber bearings including superior damping properties, lower incurred cost, light weight and easily available material. This study suggests that using the STRP as low cost base isolation device for ordinary residential buildings is feasible.     

Dynamic FE simulation of four‐story steel frame modeled by solid elements and its validation using results of full‐scale shake‐table test

Dynamic finite element analyses of a four‐story steel building frame modeled as a fine mesh of solid elements are performed using E‐Simulator, which is a parallel finite element analysis software package for precisely simulating collapse behaviors of civil and building structures. E‐Simulator is under development at the National Research Institute for Earth Science and Disaster Prevention (NIED), Japan. A full‐scale shake‐table test for a four‐story frame was conducted using E‐Defense at NIED, which is the largest shaking table in the world. A mesh of the entire structure of a four‐story frame with approximately 19 million degrees of freedom is constructed using solid elements. The density of the mesh is determined by referring to the results of elastic–plastic buckling analyses of a column of the frame using meshes of different densities. Therefore, the analysis model of the frame is well verified. Seismic response analyses under 60, 100, and 115% excitations of the JR Takatori record of the 1995 Hyogoken‐Nanbu earthquake are performed. Note that the simulation does not reproduce the collapse under the 100% excitation of the Takatori record in the E‐Defense test. Therefore, simulations for the 115% case are also performed. The results obtained by E‐Simulator are compared with those obtained by the E‐Defense full‐scale test in order to validate the results obtained by E‐Simulator. The shear forces and interstory drift angles of the first story obtained by the simulation and the test are in good agreement. Both the response of the entire frame and the local deformation as a result of elastic–plastic buckling are simulated simultaneously using E‐Simulator. Copyright © 2014 John Wiley & Sons, Ltd.     

Groundwater-level Changes Due to Pressure Gradient Induced by Nearby Earthquakes off Izu Peninsula, 1997

Anomalous water level changes were observed at two wells associated with seismic swarm activity off Izu Peninsula on March, 1997. These are coseismic water level drops followed by gradual postseismic water level rise at the time of large earthquakes during the swarm activity. The post-seismic water level rises, which can be fitted by an exponential function with a time constant of about six hours, are explained in terms of the horizontal pressure diffusion due to the pressure gradient in the aquifer induced by the coseismic static strain.