Triaxial test has been widely used to investigate the stress–strain relationship of unsaturated soils. During triaxial testing, soil volume is an essential parameter to be measured. For an unsaturated soil, due to the presence of air phase, accurate volume/deformation measurement during triaxial testing was a great challenge for researchers. Recently, a photogrammetry-based method has been developed to measure the soil volume/deformation during triaxial testing. Preliminary triaxial test results indicate the new method is simple, accurate, and cost- and time-effective. However, some concerns regarding its measurement accuracy and applicability, which are critical for the dissemination of the photogrammetry-based method, have been raised by other researchers. These concerns were addressed in details in this study. The factors concerning the deformation measurement accuracy were systematically evaluated through a series of triaxial tests on an aluminum cylinder with different confining media and chamber pressures. A sensitivity analysis was carried out to investigate the impact of the system parameters on the volume measurement accuracy of the photogrammetry-based method. In addition, a triaxial test on a saturated sand specimen was conducted to evaluate the influences of mesh density, mesh pattern, and interpolation technique on the volume change measurement accuracy. Finally, some suggestions were provided to improve the accuracy of the photogrammetry-based measurement method.
The improved element partition method (IEPM) is a newly developed fracture simulation approach. IEPM allows a fracture to run across an element without introducing extra degrees of freedom. It can also simulate any number of fractures in a prescribed mesh without remeshing. In this study, the IEPM is extended to hydraulic fracture simulation. First, the seepage and volumetric storage matrix of a cracked element are derived using virtual nodes (the intersection points of a crack with element edges). Subsequently, the fully coupled hydromechanical equation is derived for this cracked element. To eliminate the extra degrees of freedom (virtual nodal quantities), the water pressure and displacement of the virtual nodes are associated with their adjacent nodes through least squares interpolation. Finally, the fully coupled equation in terms of nodal quantities is obtained. The verification cases validate the method. By using this method, the field-scale hydraulic fracturing process is well simulated. The proposed approach is simple and efficient for field-scale hydraulic fracture simulation. 相似文献
The Xiuwenghala gold deposit is located in the Beishan Orogen of the southern Central Asian Orogenic Belt. The vein/lenticular gold orebodies are controlled by Northeast‐trending faults and are hosted mainly in the brecciated/altered tuff and rhyolite porphyry of the Lower Carboniferous Baishan Formation. Metallic minerals include mainly pyrite and minor chalcopyrite, arsenopyrite, galena, and sphalerite, whilst nonmetallic minerals include quartz, chalcedony, sericite, chlorite, and calcite. Hydrothermal alterations consist of silicic, sericite, chlorite, and carbonate. Alteration/mineralization processes comprise three stages: pre‐ore silicic alteration (Stage I), syn‐ore quartz‐chalcedony‐polymetallic sulfide mineralization (Stage II), and post‐ore quartz‐calcite veining (Stage III). Fluid inclusions (FIs) in quartz and calcite are dominated by L‐type with minor V‐type and lack any daughter mineral‐bearing or CO2‐rich/‐bearing inclusions. From Stages I to III, the FIs homogenized at 240–260°C, 220–250°C, and 150–190°C, with corresponding salinities of 2.9–10.9, 3.2–11.1, and 2.9–11.9 wt.% NaCl eqv., respectively. The mineralization depth at Xiuwenghala is estimated to be relatively shallow (<1 km). FI results indicate that the ore‐forming fluids belong to a low to medium‐temperature, low‐salinity, and low‐density NaCl‐H2O system. The values decrease from Stage I to III (3.7‰, 1.7–2.4‰, and ?1.7 to 0.9‰, respectively), and a similar trend is found for their values (?104 to ?90‰, ?126 to ?86‰, and ?130 to ?106‰, respectively). This indicates that the fluid source gradually evolved from magmatic to meteoric. δ34S values of the hydrothermal pyrites (?3.0 to 0.0‰; avg. ?1.1‰) resemble those of typical magmatic/mantle‐derived sulfides. Pyrite Pb isotopic compositions (206Pb/204Pb = 18.409–18.767, 207Pb/204Pb = 15.600–15.715, 208Pb/204Pb = 38.173–38.654) are similar to those of the (sub)volcanic ore host, indicating that the origin of ore‐forming material was mainly the upper crustal (sub)volcanic rocks. Integrating evidence from geology, FIs, and H–O–S–Pb isotopes, we suggest that Xiuwenghala is best classified as a low‐sulfidation epithermal gold deposit. 相似文献
Long-chain alkyl diols contain an alkyl chain with alcohol groups at C1 and at the middle position of carbon chain, which exist widely in seas, rivers and lakes. It has been proven that these compounds are relatively resistant to degradation and have an extended occurrence in the geological record. In addition, they are relatively easy to identify. Therefore, long-chain alkyl diols can be used as potential biomarkers to trace the past change in paleoenvironment and paleoclimate. Although the sources of long-chain alkyl diols are still uncertain, the studies indicate that 1, 13 and 1, 15-diols are mainly produced by eustigmatophytes, while 14-diols are mainly from diatom Proboscia. So far, some proxies based on long-chain alkyl diols have been established to indicate the change in diatom productivity, upwelling intensity, salinity, sea surface temperature, riverine organic matter input and surface seawater nutrient concentration, which are significant for paleoenvironmental reconstruction. Current research and application of long-chain alkyl diols proxies were summarized, which would be helpful for further studying the source of long-chain alkyl diols and the application of relevant proxies in China’s marginal sea. 相似文献