人造热带气旋垂直结构问题初探

在人造热带气旋中引入了倾斜垂直结构，并将其用于西折后9806号热带气旋登陆路径的数值模拟。结果表明：应用该方案所得到的模拟结果优于应用正压结构的人造热带气旋方案的模拟结果要准确。因此，此类热带气旋的预报中，其初始涡旋可采用倾斜垂直结构，从而提出改进热带气旋初始涡旋的一种新思路。若对其作进一步研究、推广，则具有广阔的业务应用前景。     

乾安地区盐碱地显热通量的测量

文中给出了用大孔径闪烁仪在 2 0 0 0年生长季观测到的盐碱地区显热通量的主要结果 ,并初步计算了当地的水热平衡状况。结果表明 :乾安盐碱地区显热通量占净辐射量的百分比在干旱、非生长季达到 6 5 % ,在多雨、植被生长季仅为 11% ;显热通量因降水而明显降低 ,幅度与降水强度有关 ,反映了当地的气候和土壤特征。文中还把LAS的测量结果与传统的梯度法作了比较 ,结果基本一致。     

平凉地区对流风暴地闪活动与环境层结因子相关性分析

利用1997年和1998年6－8月间在甘肃平凉地区的3站闪电定位系统所取得的地闪资料与当天早晨探空资料进行了初步的统计分析。分析结果，对流风暴中地闪活动与环境层结因子之间有较好的相关性，不稳定度、余额不稳定度5℃处的环境温度、温度层结中（中层）平均相对湿度是影响对流风暴中地闪活动的重要因子，对流风暴的地闪活动可通过这些因子进行预报。     

雨量器(计)安装不水平造成的测量误差分析及对策

降水量是气象台站重要观测项目之一。目前，大部分基层台站用于降水量观测的仪器主要靠雨量器、翻斗式遥测雨量计和虹吸式雨量计３种。《地面气象观测规范》规定：雨量器在安装和使用过程中都必须水平，以保证所测降水数据的准确性。但在实际工作中，由于各种原因往往会使器口倾斜。尤其是雨量器结构粗糙且每次观测都要取下承水器，稍不注意就会发生倾斜。那么雨量仪器安装不水平对测量水有何影响呢？大部分观测员都认为会比实际雨量偏小，其实不尽然。本文试图通过对不同降水情况下的误差进行分析，同时提供一些消除误差的方法供参考。为了…     

用逐步回归预测棉铃虫发生期和发生量

收集了1973年至2000年的气象，农作物、棉铃虫虫害等196年因子，以运城、汾阳和临汾为山西省代表站，利用最优二分割法把发生量分为10级，5级和不分级3种情况；使用逐步回归计算了219个模型，从中选出27个棉铃虫二、三代发生期，发生量最优模型，在农气服务中应用，预报准确率为95％，效果良好。     

反扩散格式在二维锋生数值模拟中的应用

把无粘流中能成功捕捉接触间断的反扩散差分格式，用在了准地转二维理想锋生的数值模拟中，并将计算结果与Cullen的计算结果和半地转方程的精确解进行了比较。用反扩散格式模拟的锋面较Cullen的结果更加显，而且更接近半地转方程的精确解。     

阿尔金地区构造应力场及其对金属矿产分布的控制作用

构造应力场研究可以为区域矿产预测提供依据。主要根据节理、擦痕的测试分析，结合区域构造解析，确定阿尔金山东西向拉配泉－－红柳沟构造带经历了三期不同方向的应力作用：印支期以前的南北向挤压作用，印支－燕山期的北西－南东向的挤压和中生代晚期－新生代北东东－南南西向的挤压；并利用有限元数值模拟前两期构造应力场的演变过程，进而讨论了区域构造应力场对内生金属矿产分布规律的控制作用指出了区域寻找大型内生金属矿产的有利地段。     

武汉市区第四系含水层地下水有机污染敏感性研究

在详细调查武汉市水文地质条件和地下水污染现状的基础上，获得了高精度的武汉市水环境中微量有机污染物的组成数据。所检测出的有机组分达30余种，以苯及相关苯系物为主，污染程度较高的地下水主要分布在人口密集区和工业，商业区，应用改进的DRASTIC模型－地下水污染敏感性评价模型，在GIS平台上，编制了武汉市区地下水污染敏感性分区图。根据其评价结果，建议集中对那些敏感性相对较高的区域采取有效的环保措施，开发利用时应作出风险评价。     

A mathematical hysteretic model for elastomeric isolation bearings

An analytical model for high damping elastomeric isolation bearings is presented in this paper. The model is used to describe mathematically the damping force and restoring force of the rubber material and bearing. Ten parameters to be identified from cyclic loading tests are included in the model. The sensitivity of the ten parameters in affecting the model is examined. These ten parameters are functions of a number of influence factors on the elastomer such as the rubber compound, Mullins effect, scragging effect, frequency, temperature and axial load. In this study, however, only the Mullins effect, scragging effect, frequency and temperature are investigated. Both material tests and shaking table tests were performed to validate the proposed model. Based on the comparison between the experimental and the analytical results, it is found that the proposed analytical model is capable of predicting the shear force–displacement hysteresis very accurately for both rubber material and bearing under cyclic loading reversals. The seismic response time histories of the bearing can also be captured, using the proposed analytical model, with a practically acceptable precision. Copyright © 2002 John Wiley & Sons, Ltd.     

Optimal design of passive energy dissipation systems based on H∞ and H2 performances

Passive energy dissipation devices (EDDs), such as viscous dampers, viscoelastic dampers, etc., have been used to effectively reduce the dynamic response of civil infrastructures, such as buildings and bridges, subject to earthquakes and strong winds. The design of these passive energy dissipation devices (EDDs) involves the determination of the optimal locations and the corresponding capacities. In this paper, we present two optimal design methodologies for passive EDDs based on active control theories, including H_∞ and H₂ performances, respectively. The optimal design methodologies presented are capable of determining the optimal locations and the corresponding capacities of EDDs. Emphasis is placed on the application of linear matrix inequality (LMI) for the effective design of passive EDDs using the popular MATLAB toolboxes. One important advantage of the proposed approaches is that the computation of the structural response is not needed in the design process. The proposed optimal design methodologies have been applied to: (i) a 10‐storey building and a 24‐storey building both subject to earthquake excitations, and (ii) a 76‐storey wind‐excited benchmark building, to demonstrate the advantages of the proposed design methodologies over the conventional equal capacity design. Copyright © 2002 John Wiley & Sons, Ltd.