Inversion of arrival-times in a region of dilatancy anisotropy

Shear-wave splitting has been identified in many three-component seismograms from two separate field experiments on a section of the North Anatolian Fault in North-West Turkey. These observations are consistent with shear-wave propagation through a zone of extensive-dilitancy anisotropy. A preliminary attempt has been made to confirm this interpretation by simultaneously inverting suites of arrival-times for hypocentral locations and for parameters describing an anisotropic halfspace. Although the inversion procedure is not globally convergent, it is possible to recognize the true solution by systematically varying the initial conditions. Applied to selected data sets, the inversion defines several anisotropic models that fit the data significantly better than a simple isotropic model, and display the anisotropy required by the shear-wave splitting. However, most of these anisotropic models are not superior when they are used to individually locate events in a much larger data set. However, for each experiment, there is a single model that produces clearly superior locations for the larger data sets than those of other anisotropic or simple isotropic models. Both models display similar velocity variations which are characteristic of propagation through distributions of biplanar cracks displaying orthorhombic symmetry. The principal axes of the two models are oriented in similar directions and are within 20° of the principal axis of regional stress derived from fault-plane solutions. The solutions indicate low velocities close to the tensional axis, as would be expected in extensive-dilatancy anisotropy.     

The generation ofK indices from digitally recorded magnetic data

TheK index was developed by Bartels and is a measure of geomagnetic activity. The important feature of this index is that it is a measure of solar activity superimposed on the regular daily variation.It is the most used estimate of activity being of particular interest to researchers in ionospheric physics and telecommunications.In response to increased availability of digital data from magnetic observatories and their demand by the scientific community it becomes desireable to check whetherK indices produced from magnetograms plotted from digital data are consistent with those handscaled from La Cour charts.This paper presents results of these comparisons and also reports on several methods tested to produce theK index directly from the digital data.Handscaled indices from digital plots are suitable for producing theK index. Computations using digital data do not reproduceK as defined by Bartels precisely but do provide an equivalent index which is satisfactory for most user and research purposes.     

Slope process change and colluvium deposition in Swaziland: An SEM analysis

Electron microscope analysis of sixty samples taken from six colluvium sites in Swaziland has shown that the quartz grains exhibit marked edge abrasion in the uppermost beds of exposures. This edge abrasion is lacking in the lower beds in all sections examined and indicates slope process change during colluvium deposition. A model of slope evolution is provided, in which slope erosion progressively brings about more channelling and causes greater surface roughness because of the exhumation of more core stones and differentially weathered rock. This roughness causes increased edge abrasion.     

Aluminous goethite: A mössbauer study

Mössbauer measurements at 300 K, 77 K and 4.2 K and X-ray data are presented for synthetic aluminous goethites (α Fe_1?x Al _x OOH) in two series containing up to 15 mole percent aluminium (hydrothermal preparation) and 19 mole percent aluminium (low-temperature preparation). The Mössbauer spectra for specimens at 300 K and 77 K display broadened and relaxed line-shapes with the relaxation rate increasing with aluminium substitution, whereas all the 4.2 K spectra can be described by a single magnetically split spectrum. At 4.2 K the magnitude of this splitting is 505 kOe for pure goethite and it decreases by 0.52 kOe per mole percent aluminium substitution. The absolute value of the recoil-free fraction f at 4.2 K has been measured for pure goethite and for aluminous goethites containing 7, 15 and 19 mole percent aluminium; it increases from f=0.69±0.02 to f=0.89±0.02 in this range. The increase is attributed to a stiffening of the goethite lattice as it contracts to accommodate the smaller aluminium ion. At 300 K f is found to decrease from f=0.65±0.05 for pure goethite to f=0.50±0.03 for goethite with 19 mole percent aluminium.     

Acute toxicity of bis(tributyltin) oxide to a marine copepod

A static renewal toxicity test was conducted to evaluate the response of the copepod Acartia tonsa to bis(tributyltin) oxide (TBTO), the active compound of recently developed antifouling paints. Copepods were individually placed in test tubes containing 4 ml of 0.3, 0.5, 1.0, 1.7 or 3.0 μg l^?1 TBTO with acetone and seawater. Thirty copepods were used for each treatment and control condition and all solutions were renewed daily. The 96-h LC₅₀ was 1.0 μg l^?1 with a 95% confidence interval between 0.8 and 1.2 μg l^?1 TBTO. The 144-h EC₅₀ was 0.4 μg l^?1 TBTO which approaches concentrations recently measured in San Diego Bay. Some copepods exposed to 0.3 μg l^?1 TBTO became moribund after six days.     

Characterization of the Structure of River-Bed Gravels Using Two-Dimensional Fractal Analysis

This paper is concerned with the application of fractal analysis to understand the structure of water-worked gravel-bed river surfaces. High resolution digital elevation models, acquired using digital photogrammetric methods, allowed the application of two-dimensional fractal methods. Previous gravel-bed river studies have been based upon sampled profiles and hence one-dimensional fractal characterisation. After basic testing that bed elevation increments are Gaussian, the paper uses two-dimensional variogram surfaces to derive directionally dependent estimates of fractal dimension. The results identify mixed fractal behavior with two characteristic fractal bands, one associated with the subgrain scale and one associated with the grain scale. The subgrain scale characteristics were isotropic and sensitive to decisions made during the data collection process. Thus, it was difficult to differentiate whether these characteristics were real facets of the surfaces studied. The second band was anisotropic and not sensitive to data collection issues. Fractal dimensions were greater in the downstream direction than in other directions suggesting that the effects of water working are to alter the level of surface organisation, by increasing surface irregularity and hence roughness. This is an important observation as it means that water-worked surfaces may have a distinct anisotropic signal, revealed when using a fractal type analysis.