Electron accepting capacity of dissolved organic matter as determined by reaction with metallic zinc

Information about the chemical electron accepting capacity (EAC) of dissolved organic matter (DOM) is scarce owing to a lack of applicable methods. We quantified the electron transfer from metallic Zn to natural DOM in batch experiments at DOC concentrations of 10–100 mg-C L^− 1 and related it to spectroscopic information obtained from UV-, synchronous fluorescence, and FTIR- spectroscopy. The electron donating capacity of DOM and pre-reduced DOM was investigated using Fe(CN)₆³⁻ as electron acceptor. Presence of DOM resulted in release of dissolved Zn, consumption of protons, and slower release of hydrogen compared to reaction of metallic Zn with water at pH 6.5. Comparison with reaction stoichiometry confirmed that DOM accepted electrons from metallic Zn. The release of dissolved Zn was dependent on pH, DOC concentration, ionic strength, and organic matter properties. The reaction appeared to be completed within about 24 h and was characterized by pseudo first order kinetics with rate constants of 0.5 to 0.8 h^− 1. EAC per mass unit of carbon ranged from 0.22 mmol g^− 1 C to 12.6 mmol g^− 1 C. Depending on the DOM, a calculated 28–127% of the electrons transferred from metallic Zn to DOM could be subsequently donated to Fe(CN)₆³⁻. EAC decreased with DOC concentration, and increased with aromaticity, carboxyl, and phenolic content of the DOM. The results indicate that an operationally defined EAC of natural DOM can be quantified by reaction with metallic Zn and that DOM properties control the electron transfer. Shortcomings of the method are the coagulation and precipitation of DOM during the experiment and the production of hydrogen and dissolved Zn by reaction of metallic Zn with water, which may influence the determined EAC.     

Another Record: Ocean Warming Continues through 2021 despite La Ni?a Conditions

The increased concentration of greenhouse gases in the atmosphere from human activities traps heat within the climate system and increases ocean heat content (O...     

The status of research and utilisation on the subtidal kelp along the Chilean coast: A literature review

The most important marine coastal ecosystem in the Chilean coast are kelp forests. This review is based on ecological studies regarding different aspects of subtidal kelp ecosystems along the Chilean coast. It highlights the most interesting findings in (1) biology of subtidal kelp in Chile, with particular reference to (2) habitats formed by kelp, and considered the successful examples and promising results in the (3) kelp as an industrial resource (Biotechnological approach of kelps and aquaculture). The impact caused by (4) El Ni?o-Southern Oscillation is discussed as an important climatic event that could help to forecast the future of the kelp ecosystem. In addition, this literature review outlines the knowledge gaps on subtidal kelp along the Southeast Pacific Coast of Chile, so that research can be strengthened in the future.     

The sensitivity of the Late Saalian (140?ka) and LGM (21?ka) Eurasian ice sheets to sea surface conditions

This work focuses on the Late Saalian (140?ka) Eurasian ice sheets?? surface mass balance (SMB) sensitivity to changes in sea surface temperatures (SST). An Atmospheric General Circulation Model (AGCM), forced with two preexisting Last Glacial Maximum (LGM, 21?ka) SST reconstructions, is used to compute climate at 140 and 21?ka (reference glaciation). Contrary to the LGM, the ablation almost stopped at 140?ka due to the climatic cooling effect from the large ice sheet topography. Late Saalian SST are simulated using an AGCM coupled with a mixed layer ocean. Compared to the LGM, these 140?ka SST show an inter-hemispheric asymmetry caused by the larger ice-albedo feedback, cooling climate. The resulting Late Saalian ice sheet SMB is smaller due to the extensive simulated sea ice reducing the precipitation. In conclusion, SST are important for the stability and growth of the Late Saalian Eurasian ice sheet.     

Analysis of the parameterization for the wind-velocity fluctuation standard deviations in the surface layer in low-wind conditions

In this work a formulation for the standard deviations of the wind-velocity fluctuations in the atmospheric surface layer is assessed for heterogeneous conditions and with a particular focus on calm wind regime. Starting from a standard formulation used in the devoted literature, its empirical coefficients are estimated by analysing three sets of surface-layer observed data. The possibility of inferring a formula for these coefficients as functions of the wind speed is investigated. The curves of the standard deviations as functions of the stability show different behaviours depending on the set of coefficients used, even if the values of these do not affect the overall statistical agreement between predicted and observed standard deviations. Referring to typical literature values of the coefficients, it is shown that the agreement certainly improves when distinguishing them for two wind-speed regime, low-wind and windy.     

Predictability of the mid-latitude Atlantic meridional overturning circulation in a multi-model system

Assessing the skill of the Atlantic meridional overturning circulation (AMOC) in decadal hindcasts (i.e. retrospective predictions) is hampered by a lack of observations for verification. Models are therefore needed to reconstruct the historical AMOC variability. Here we show that ten recent oceanic syntheses provide a common signal of AMOC variability at 45°N, with an increase from the 1960s to the mid-1990s and a decrease thereafter although they disagree on the exact magnitude. This signal correlates with observed key processes such as the North Atlantic Oscillation, sub-polar gyre strength, Atlantic sea surface temperature dipole, and Labrador Sea convection that are thought to be related to the AMOC. Furthermore, we find potential predictability of the mid-latitude AMOC for the first 3–6 year means when we validate decadal hindcasts for the past 50 years against the multi-model signal. However, this predictability is not found in models driven only by external radiative changes, demonstrating the need for initialization of decadal climate predictions.     

Alteration of fluid properties during the initial operation of a geothermal plant: results from in situ measurements in Groß Schönebeck

Recently, the thermal fluid loop has been established and continuosly operated for 7 days at the geothermal in situ laboratory in Groß Schönebeck (North German Basin). During this initial phase of fluid production, the fluid temperature, measured at the surface, continuously increased until a stable value of about 98 °C was established. Fluid physicochemical properties (pH, redox, density, temperature, and pressure) were measured online and in situ with a newly developed fluid monitoring system (FluMo). Additionally, fluid samples have been collected at various temperatures (in 5–10 °C steps) directly at the production well at about 10 bar pressure. From the pressurized sampling tool, the fluid was directly transferred into a heated autoclave, which allowed filtration (0.2 μm) in the absence of oxygen. Physicochemical parameters [pH, redox, electric conductivity, total dissolved solids (TDS)] as well as acid capacity (K _S 4.3) of these samples have been measured onsite at atmospheric conditions. Concentrations of anions, total organic carbon, and metals were analyzed later in the laboratory. Both, measurements in collected samples or in situ (FluMo) analysis of most the parameters density, electric conductivity, or TDS indicated relatively constant values over the whole production time (1.17–1.18 g · cm^?3, 215–221 mS · cm^?1, 241–260 g · L^?1, respectively). Good correlation was also found for pH values (pH = 6.6–6.9), whereas the redox values varied between ?1 and 46 mV when determined at 25 °C and decreased strongly when measured in situ with increasing temperature (?110 mV at 90 °C). The elemental composition of collected samples remained also relatively constant for most compounds and was clearly higher as compared with samples collected in 2011. Results of this study demonstrate that realistic, comprehensive, and time-resolved physicochemical data can be obtained by FluMo. These detailed data sets can be crucial to understand the complex geochemical processes in a thermal water loop and eventually to take required measures on time.