Weathered rockfill materials, characterized by a mixture of soil matrix and rock aggregates, are widely distributed in mountainous areas. These soils are frequently used for subgrade or riprap in engineering practice, and the mobilized shear strength is crucial for analyzing the displacement and stability of these geo-structures. A series of direct shear tests are performed on a gap-graded soil with a full range of coarse fraction. The behavior of gap-graded soils is analyzed, and a simple model is proposed for the evolution of mobilized stress ratio during direct shearing process based on mixture theory. The change of inter-aggregate configuration is incorporated by introducing a structure variable which increases with coarse fraction and decreases approximately linearly with the overall horizontal shear strain in double logarithmic plot. It reasonably reflects a gradually transformation from a matrix-sustained structure into an aggregate-sustained one with the increase of coarse fraction. The model has four parameters, and at least two direct shear tests need to be done for the calibration. Validation of the model is done by using the test data in this work and those from the literature.
Self-feeding device is extensively used in aquaculture farms, but for salmonids the individual feeding behavior has seldom been continuously observed. In this article, the individual self-feeding behavior of 10 rainbow trout was continuously monitored with a PIT tag record for 50 days with three replicates. The fish fell into three categories according to their feeding behavior, i.e. high triggering fish (trigger behavior more than 25% of the group, HT), low triggering fish (1%–25%, LT) and zero triggering fish (less than 1%). The results showed that in a group of 10 individual 1–2 HT fish accounted for most of the self-feeding behavior (78.19%–89.14%), which was far more than they could consume. The trigger frequency of the fish was significantly correlated with the initial body weight (P <0.01), however, no significant difference in growth rate among the HT, LT, and ZT fish was observed (P >0.05). Cosinor analysis showed that the two HT fish in the same group had similar acrophase. Though some of the HT fish could be active for 50 d, there were also HT fish decreased triggering behavior around 40 d and the high trigger status was then replaced by other fish, which was first discovered in salimonds. Interestingly, the growth of the group was not affected by the alternation triggering fish. These results provide evidence that in the self-feeding system the HT fish didn’t gain much advantage by their frequent self-feeding behavior, and high trigger status of the HT fish is not only an individual character but also driven by the demand of the group. In the self-feeding system, the critical individual should be closely monitored.
AbstractWith the growing demand for underwater refill engineering, the construction technology of implementing fluidized solidification in underwater pouring has recently received increased attention. However, the environmental impact of underwater casting on surrounding water bodies, especially when the silt is polluted, is still unclear. In this study, a simulated underwater pouring test and a static immersion release test were conducted separately to study the quality of the surrounding water during and after pouring. The results showed that fluidized-solidified silt casting could increase the pH of the surrounding water, even after the pouring had stopped, by approximately 1.0 and the turbidity could reach 200 NTU. No diffusion of Zn and Cu into the surrounding water was observed and while Ni and Cr exhibited slight diffusion, this was at a level well below international water quality standard. During construction, reducing the distance from the seafloor to the bottom of the pouring catheter could reduce the level of pollution. After construction, the use of neutral solidified materials can effectively reduce the pH of the surrounding water and the potential risk of heavy metal dissolution. 相似文献
In this work, enhanced poly(3-hexylthiophene):[6,6]-phenyl-C61-butyric acid methyl ester (P3HT:PCBM) bulk-heterojunction photovoltaic devices are achieved via slow-solvent-vapour treatment. The correlations between the morphology of the active layer and the photovoltaic performance of polymer-based solar cell are investigated. The active layers are characterized by atomic force microscopy and optical absorption. The results show that slow-solvent-vapour treatment can induce P3HT self-organization into an ordered structure, leading to the enhanced absorption and efficient charge transport. 相似文献