Investigating the effects of lateral stress to vertical stress ratios and caverns shape on the cavern stability and sidewall displacements

Effects of lateral stress to vertical stress ratio on behavior of a cavern in various geomechanical and geometrical conditions were studied. Results indicated that the range of one to two lateral stress to vertical stress ratios was the best condition for cavern stability. The ranges causing tension and compressive failure were specified as well. Two-dimensional stability analyses were carried out by using Phase². Key point location on the cavern side wall was investigated and determined using an equation based on a large number of numerical analyses. Subsequently, in order to predict the elasto-plastic displacement and elastic displacement on a side wall key point, two equations were fitted based on various cavern cross sections considering four basic factors, i.e., rock deformation modulus, overburden depth of caverns, heights of the caverns, and the lateral stress to vertical stress ratio. The proposed equations were utilized to predict displacement at the key points of 10 projects subsequent to which the computation results were compared to in-site measuring results and back analysis results. Finally, using key point displacement as a stability factor, the effects of three different shapes of caverns including mushroom, horse shoe, and elliptical were investigated on cavern stability. The most optimum shape was elliptical in a vast range of lateral stress to vertical stress ratios; mushroom and horse shoe shapes were preferred in uniaxial stress fields concerning the rock quality.     

A robust feldspar luminescence dating method for Middle and Late Pleistocene sediments

Luminescence dating is used extensively to provide absolute chronologies for Late Pleistocene sediments. Nowadays, most optical dates are based on quartz optically stimulated luminescence (OSL). However, the application of this signal is usually limited to the last ～100 ka because of saturation of the quartz luminescence signal with dose. In contrast, the feldspar infrared stimulated luminescence (IRSL) dose–response curve grows to much higher doses; this has the potential to extend the datable age range by a factor of 4–5 compared with quartz OSL. However, it has been known for several decades that this IRSL signal is unstable, and this instability often gives rise to significant age underestimation. Here we test against independent age control the recently developed feldspar post‐IR IRSL approach to the dating of sediments, which appears to avoid signal instability. A physical model explaining our observations is discussed, and the method is shown to be accurate back to 600 ka. The post‐IR IRSL signal is reduced by exposure to daylight more slowly than that from quartz and low‐temperature IRSL, preventing its general application to young (e.g. Holocene) sediments. Nevertheless, this new approach is widely applicable (feldspar of appropriate luminescence behaviour is even more ubiquitous than quartz). These characteristics make this a method of great importance for the dating of Middle and Late Pleistocene deposits.     

Geochemistry of Carboniferous Sandstones (Sardar Formation), East‐Central Iran: Implication for Provenance and Tectonic Setting

Geochemical analysis of sandstones from the Sardar Formation (from two stratigraphic successions) in east-central Iran were used for identification of geochemical characterization of sandstones, provenance and tectonic setting. Sandstones in the two lithostratigraphic successions have similar chemical compositions suggesting a common provenance. Bulk-rock geochemistry analysis of Carboniferous sandstones from Sardar Formation indicates that they are mainly quartz dominated and are classified as quartzarenites, sublitharenites and subarkoses, derived from acid igneous to intermediate igneous rocks. Discrimination function analysis indicates that the sandstones of Sardar Formation were derived from quartzose sedimentary provenance in a recycled orogenic setting. Also, major and trace elements in sandstones of Sardar Formation (e.g., K2O/Na2O vs. SiO2) indicate deposition in a stable passive continental margin (PM). Chemical index of alteration (CIA) for these rocks (> 65%) suggests a moderate to relatively high degree of weathering in the source area.     

Site selection for managed aquifer recharge using fuzzy rules: integrating geographical information system (GIS) tools and multi-criteria decision making

One of the most important water-resources management strategies for arid lands is managed aquifer recharge (MAR). In establishing a MAR scheme, site selection is the prime prerequisite that can be assisted by geographic information system (GIS) tools. One of the most important uncertainties in the site-selection process using GIS is finite ranges or intervals resulting from data classification. In order to reduce these uncertainties, a novel method has been developed involving the integration of multi-criteria decision making (MCDM), GIS, and a fuzzy inference system (FIS). The Shemil-Ashkara plain in the Hormozgan Province of Iran was selected as the case study; slope, geology, groundwater depth, potential for runoff, land use, and groundwater electrical conductivity have been considered as site-selection factors. By defining fuzzy membership functions for the input layers and the output layer, and by constructing fuzzy rules, a FIS has been developed. Comparison of the results produced by the proposed method and the traditional simple additive weighted (SAW) method shows that the proposed method yields more precise results. In conclusion, fuzzy-set theory can be an effective method to overcome associated uncertainties in classification of geographic information data.     

Seismicity patterns associated with the September 10th, 2008 Qeshm earthquake, South Iran

The b value of the Gutenberg-Richter relation and the standard deviate, Z, were calculated to investigate the temporal and spatial variations in seismicity patterns associated with the September 10th, 2008 (Mw?=?6.1) Qeshm earthquake. The temporal variations of b value illustrate a distinct dramatic drop preceding the Qeshm earthquake, and the spatial changes in b value highlight a zone with an abnormally low b value around the epicenter of this event. The cumulative number and Z value as a function of time show a precursory seismic quiescence preceding the 2008 Qeshm earthquake that observed for 1?year in a circle with R?=?50?km around its epicenter. The spatial distribution map of the standard deviate, Z, also exhibits an obvious precursory seismic quiescence region before the 2008 Qeshm event around the epicenter of this event. Interestingly, the precursory seismic quiescence region is approximately consistent with low b value anomaly region, and both have E–W to NE–SW trend. These two precursory anomalies took place in relatively large regions, which were possibly relevant to the preparation zone of the 2008 Qeshm event.     

Geochemical characteristics of the mud volcano fluids in southwestern Taiwan and their possible linkage to elevated arsenic concentration in Chianan plain groundwater

Fluid and mud samples were collected from Wushanting (WST), Hsiaokunshui (HKS), Yenshuikeng (YSK), Kuantzeling (KZL), and Kunshuiping (KSP) mud volcanoes of southwestern Taiwan. Concentrations of major ions and trace elements in mud volcanic fluids were analyzed to find the possible linkage to elevated arsenic (As) concentrations in the Chianan plain groundwater. The elevated Na⁺, K⁺, and Cl⁻ concentrations indicated possible marine origin of the fluids. The trace element concentrations in the mud volcanic fluids were generally low, but the As concentrations were up to 0.12 mg/L. High contents of As, Fe, and Mn were observed in the mud samples. Saturation index calculations indicated that both carbonate and oxide minerals acted as potential sinks for As in the mud volcanic fluids. Arsenic in the dewatering fluids and muds may be transported by the subsurface flow and surface streams as suspended solids and eventually deposited in the Chianan plain aquifers. Under reducing conditions, As may be released from the host minerals (such as Fe- and Mn-oxides/hydroxides), thereby causing widespread groundwater As pollution.     

Predicting the production rate of diamond wire saw using statistical analysis

Performance prediction of diamond wire saws is important in the cost estimation and the planning of the stone quarries. An accurate estimation of sawability helps to make the planning of the rock cutting projects more efficient. In this paper, the performance prediction of diamond wire saws in cutting carbonate rocks was studied on 14 different carbonate rocks in stone quarries located in Iran. Rock samples were collected from the quarries for laboratory tests. Uniaxial compressive strength, Brazilian tensile strength, Schmidt hammer value, and Los Angeles abrasion were determined in the laboratory. Performance prediction was evaluated using simple and multiple regression analyses. Finally, a new model was proposed for predicting the production rate of diamond wire saw. It was concluded that the production rate of carbonate rock using diamond wire saw can reliably be estimated using the developed model.     

Application of randomized sampling schemes to curvelet‐based sparsity‐promoting seismic data recovery

Reconstruction of seismic data is routinely used to improve the quality and resolution of seismic data from incomplete acquired seismic recordings. Curvelet‐based Recovery by Sparsity‐promoting Inversion, adapted from the recently‐developed theory of compressive sensing, is one such kind of reconstruction, especially good for recovery of undersampled seismic data. Like traditional Fourier‐based methods, it performs best when used in conjunction with randomized subsampling, which converts aliases from the usual regular periodic subsampling into easy‐to‐eliminate noise. By virtue of its ability to control gap size, along with the random and irregular nature of its sampling pattern, jittered (sub)sampling is one proven method that has been used successfully for the determination of geophone positions along a seismic line. In this paper, we extend jittered sampling to two‐dimensional acquisition design, a more difficult problem, with both underlying Cartesian and hexagonal grids. We also study what we term separable and non‐separable two‐dimensional jittered samplings. We find hexagonal jittered sampling performs better than Cartesian jittered sampling, while fully non‐separable jittered sampling performs better than separable jittered sampling. Two other 2D randomized sampling methods, Poisson Disk sampling and Farthest Point sampling, both known to possess blue‐noise spectra, are also shown to perform well.     

Interaction of a Fresh Water Lake and a Karstic Spring via a Syncline Fold

Kaftar Lake is a high‐altitude fresh water lake located in High Zagros, south of Iran. Despite the high annual evaporation to precipitation ratio in the area, lake water electrical conductivity is usually lower than 1000 µS/cm, this may be due to high seepage from the floor of the lake. Therefore, the hypothesis of possible underground connections between Namdan Basin, where the lake is located, and the surrounding basins with lower elevation (Aspas and Dehbid Basins) was investigated. Hydrogeology, hydrochemistry, and stable isotopes data of the lake and surrounding basins along with the lake water balance study were applied to test the hypothesis. Results indicate that Kaftar Lake has no connection with Aspas Basin in south, but it is hydraulically connected to Dehbid Basin. In Dehbid Basin, “Ghasr_e_Yaghoob spring” (average discharge ?1200 L/s) emerges from a small outcrop (about 0.8 km²) of Daryan limestone Formation, where this outcrop is much smaller than the required recharge area for such average discharge rate. The study shows that this spring is recharged by Kaftar Lake and Namdan Basin aquifer, through Daryan Formation of Gandboee Syncline located to the northern part of the lake.     

Development of ground-testable phase fresnel lenses in silicon

Diffractive optics, such as Phase Fresnel Lenses (PFL's), offer the potential to achieve excellent imaging performance in the x-ray and gamma-ray photon regimes. In principle, the angular resolution obtained with these devices can be diffraction limited. Furthermore, improvements in signal sensitivity can be achieved as virtually the entire flux incident on a lens can be concentrated onto a small detector area. In order to verify experimentally the imaging performance, we have fabricated PFL's in silicon using gray-scale lithography to produce the required Fresnel profile. These devices are to be evaluated in the recently constructed 600-meter x-ray interferometry testbed at NASA/GSFC. Profile measurements of the Fresnel structures in fabricated PFL's have been performed and have been used to obtain initial characterization of the expected PFL imaging efficiencies.