Ground penetrating radar and 2D electric resistivity studies for tracing hydrocarbon leakage site,close to Abha City: a case study

This work presents the application of the ground-penetrating radar (GPR) method and electric resistivity tomography (ERT) technique in outlining a zone of contamination due to the light non-aqueous phase liquid (LNAPL) plume underground in the area of an impacted fuel station, close to Abha City. The GPR has been performed using SIR3000 unit with the 100 and 400 MHz antennas. The main objective of the GPR survey was to evaluate the lateral extension of contamination. The complex GPR signature of the plume was well characterized. Low reflectivity zone corresponds to hydrocarbon vapor phase in the vadose zone. Enhanced reflections are associated with free and residual products in the fractured saturated zone directly above the water table. An electric resistivity tomography (ERT) survey was performed on four profiles within the site to investigate the vertical and horizontal extent of the contamination plume and to define the bottom of the landfill. The 2D electric profiles show the presence of low-resistivity (4O to 37 Ω m) anomalies that refers to the presence of accumulated hydrocarbons. From the interpretation of the GPR and ERT profile, it was possible to locate the top and bottom of the contamination plume of the waste disposal site. The radar signal penetrated deep enough and enabled the identification of a second reflector at approximately 10-m deep, interpreted as the hard basement surface which causes the strong amplitude reflection in the GPR profile. The results of GPR and ERT showed good agreement.     

Sequence stratigraphic analysis of Eocene Rock Strata,Offshore Indus,southwest Pakistan

In this study, seismic data from two wells (Pak G2-1 and Indus Marine-1C) and age diagnostic larger benthic foraminifera (LBF) within drill cuttings has been used for the first time to identify depositional sequences within the carbonates in the Offshore Indus Basin, Pakistan. The Offshore Indus is tectonically categorized as a passive continental margin where carbonates occur as shelf carbonates in the near offshore and on volcanic seamounts in deeper waters. Seismic data analysis has indicated the presence of minor faults and carbonate buildups above the igneous basement in the south. Patterns of the seismic reflections enabled definition of three seismic facies units identified as: Unit 1 basement, represented by chaotic, moderate amplitude reflection configuration; while parallel bedding and the drape of overlying strata is typical character of Unit 2, carbonate mound facies. The younger Miocene channels represent Unit 3. The diagnosis of Alveolina vredenburgi/cucumiformis biozone confirmed the Ilerdian (55–52 Ma) stage constituting a second order cycle of deposition for the Eocene carbonates (identified as Unit 2). The carbonate succession has been mainly attributed to an early highstand system tract (HST). The environmental conditions remained favorable leading to the development of keep-up carbonates similar to pinnacle buildups as a result of aggradation during late transgressive system tract and an early HST. The carbonate sequence in the south (Pak G2-1) is thicker and fossiliferous representing inner to middle shelf depths based on fauna compared to the Indus Marine-1C in the north, which is devoid of fossils. Three biozones (SBZ 5, SBZ 6 and SBZ 8) were identified based on the occurrence of LBF. The base of the SBZ 5 zone marks the larger foraminifera turnover and the Paleocene–Eocene (P–E) boundary. The LBF encountered in this study coincides with earlier findings for the P–E boundary. Our findings indicate that the entire Ilerdian stage ranges from 55.5 to 52 Ma that was the episode of warmer water conditions on the carbonate shelves leading to the diversification of K-strategist larger foraminifera. The larger foraminiferal assemblage encountered in this study confirms the findings. The possible indication of stratigraphic-combination traps, revealed as reflection terminations, make carbonate mounds in the south a potential exploration target.     

Heat and mass transfer effects during displacement of deepwater methane hydrate to the surface of Lake Baikal

The present paper focuses on heat and mass exchange processes in methane hydrate fragments during in situ displacement from the gas hydrate stability zone (GHSZ) to the water surface of Lake Baikal. After being extracted from the methane hydrate deposit at the lakebed, hydrate fragments were placed into a container with transparent walls and a bottom grid. There were no changes in the hydrate fragments during ascent within the GHSZ. The water temperature in the container remained the same as that of the ambient water (~3.5 °С). However, as soon as the container crossed the upper border of the GHSZ, first signs of hydrate decomposition and transformation into free methane gas were observed. The gas filled the container and displaced water from it. At 300 m depth, the upper and lower thermometers in the container simultaneously recorded noticeable decreases of temperature. The temperature in the upper part of the container decreased to –0.25 °С at about 200 m depth, after which the temperature remained constant until the water surface was reached. The temperature at the bottom of the container reached –0.25 °С at about 100 m depth, after which it did not vary during further ascent. These observed effects could be explained by the formation of a gas phase in the container and an ice layer on the hydrate surface caused by heat consumption during hydrate decomposition (self-preservation effect). However, steady-state simulations suggest that the forming ice layer is too thin to sustain the hydrate internal pressure required to protect the hydrate from decomposition. Thus, the mechanism of self-preservation remains unclear.     

Modern modes of provenance and dispersal of terrigenous sediments in the North Pacific and Bering Sea: implications and perspectives for palaeoenvironmental reconstructions

During expedition 202 aboard the RV Sonne in 2009, 39 seafloor surface sediment sites were sampled over a wide sector of the North Pacific and adjoining Bering Sea. The data served to infer land–ocean linkages of terrigenous sediment supply in terms of major sources and modes of sediment transport within an over-regional context. This is based on an integrated approach dealing with grain-size analysis, bulk mineralogy and clay mineralogy in combination with statistical data evaluation (end-member modelling of grain-size data, fuzzy cluster analysis of mineralogical data). The findings on clay mineralogy served to update those of earlier work extracted from the literature. Today, two processes of terrigenous sediment supply prevail in the study area: far-distance aeolian sediment supply to the pelagic North Pacific, and hemipelagic sediment dispersal from nearby land sources via ocean currents along the continental margins and island arcs. Aeolian particles show the finest grain sizes (clay and fine silt), whereas hemipelagic sediments have high abundances of coarse silt. Exposed sites on seamounts and the continental slope are partly swept by strong currents, leading to residual enrichment of fine sand. Four sediment sources can be distinguished on the basis of distinct index minerals revealed by statistical data analysis: dust plumes from central Asia (quartz, illite), altered materials from the volcanic regions of Kamchatka and the Aleutian Arc (smectite), detritus from the Alaskan Cordillera (chlorite, hornblende), and fluvial detritus from far-eastern Siberia and the Alaska mainland (quartz, feldspar, illite). These findings confirm those of former studies but considerably expand the geographic range of this suite of proxies as far south as 39°N in the open North Pacific. The present integrated methodological approach proved useful in identifying the major modern processes of terrigenous sediment supply to the study region. This aspect deserves attention in the selection of sediment core sites for future palaeoenvironmental reconstructions related to aeolian and glacial dynamics, as well as the recognition of palaeo-ocean circulation patterns in general.     

Solar-, monsoon- and Kuroshio-influenced thermocline depth and sea surface salinity in the southern Okinawa Trough during the past 17,300 years

Factors influencing millennial-scale variability in the thermocline depth (vertical mixing) and sea surface salinity (SSS) of the southern Okinawa Trough (OT) during the past 17,300 years were investigated based on foraminifer oxygen isotope records of the surface dweller Globigerinoides ruber sensu stricto and the thermocline dweller Pulleniatina obliquiloculata in the AMS ¹⁴C dated OKT-3 core. The thermocline depth is influenced by surface thermal buoyancy (heat) flux, in turn controlled by the annual mean insolation at 30°N and the strength of the East Asian winter monsoon (EAWM). Strong insolation and weak EAWM tend to increase buoyancy gain (decrease buoyancy loss), corresponding to shallow thermocline depths, and vice versa. Regional SSS is influenced by the global ice volume, the Kuroshio Current (KC), and vertical mixing. A deep thermocline coincides with a high SSS because strong vertical mixing brings more, saltier subsurface KC water to the surface, and vice versa. Local SSS (excluding the global ice volume effect) became lower in the northern OT than in the southern OT after ~9.2 ka, implying that Changjiang diluted water had stronger influence in the northern sector. SSS show no major changes during the Bølling/Allerød and Younger Dryas events, probably because the KC disturbed the North Atlantic signals. This argues against earlier interpretations of sea surface temperature records of this core. Wavelet and spectral analyses of the Δδ¹⁸O_P-G (δ¹⁸O of P. obliquiloculata minus G. ruber s.s.) and δ¹⁸O_local records display 1,540-, 1,480-, 1,050-, 860-, 640-, and 630-year periods. These are consistent with published evidence of a pervasive periodicity of 1,500 years in global climate as well as EAWM and KC signatures, and a fundamental solar periodicity of 1,000 years and intermediary derived periodicity of 700 years.     

Glaciomarine sedimentation and bottom current activity on the north-western and northern continental margins of Svalbard during the late Quaternary

Palaeo-bottom current strength of the West Spitsbergen Current (WSC) and the influence of the Svalbard-Barents Sea Ice Sheet (SBIS) on the depositional environment along the northern Svalbard margins are poorly known. Two gravity cores from the southern Yermak Plateau and the upper slope north of Nordaustlandet, covering marine isotope stage (MIS) 1 to MIS 5, are investigated. Five lithofacies, based on grain size distribution, silt/clay ratio, content and mean of sortable silt (SS), are distinguished to characterise the contourite-dominated sedimentary environments. In addition, depositional environments are described using total organic carbon (TOC), total sulphur (TS) and calcium carbonate (CaCO₃) contents of sediments. Facies A, containing coarse SS, suggests strong bottom current activity and good bottom water ventilation conditions as inferred from low TOC content. This facies was deposited during the glacial periods MIS 4, MIS 2 and during the late Holocene. Facies B is dominated by fine SS indicating weak bottom current and poor ventilation (cf. high TOC content of 1.2–1.6%), and correlates with the MIS 4/3 and MIS 2/1 transition periods. With an equal amount of clay and sand, fine SS and high content of TOC, facies C indicates reduced bottom current strength for intervals with sediment supply from proximal sources such as icebergs, sea ice or meltwater discharge. This facies was deposited during the last glacial maximum. Facies D represents mass-flow deposits on the northern Svalbard margin attributed to the SBIS advance at or near the shelf edge. Facies E sediments indicating moderate bottom current strength were deposited during MIS 5 and MIS 3, and during parts of MIS 2. This first late Quaternary proxy record of the WSC flow and sedimentation history from the northern Svalbard margin suggests that the oceanographic conditions and ice sheet processes have exerted first-order control on sediment properties.     

Experimental study of nonlinear behaviors of a free-floating body in waves

Nonlinear behaviors of a free-floating body in waves were experimentally investigated in the present study. The experiments were carried out for 6 different wave heights and 6 different wave periods to cover a relatively wide range of wave nonlinearities. A charge-coupled device (CCD) camera was used to capture the real-time motion of the floating body. The measurement data show that the sway, heave and roll motions of the floating body are all harmonic oscillations while the equilibrium position of the sway motion drifts in the wave direction. The drift speed is proportional to wave steepness when the size of the floating body is comparable to the wavelength, while it is proportional to the square of wave steepness when the floating body is relatively small. In addition, the drift motion leads to a slightly longer oscillation period of the floating body than the wave period of nonlinear wave and the discrepancy increases with the increment of wave steepness.     

The Air-Coastal Sea Chemical Exchange: A Case Study on the New Jersey Coast

The coastal marine atmosphere adjacent to large urban and industrial centers is in general strongly impacted by pollution emissions, resulting in high loading of pollutants in the ambient air. Among the airborne substances are certain trace elements from a variety of emission sources that can serve as micronutrients to marine organisms in coastal waters. High concentrations of such elements in coastal air can result in enhanced air-to-sea deposition fluxes to coastal waters. They could also be transported over the open ocean, affecting the composition of the remote marine atmosphere and then ocean ecosystems. To provide better understanding of the extent of air-to-sea deposition processes on the New Jersey coast, a heavily polluted coastal region on the US East Coast, a synthesis of observation data was carried out for selected trace elements, including Fe, Cd, Cr and Cu, derived from measurements of both size-segregated and bulk aerosol particles, as well as precipitation around the New Jersey coast. The atmospheric input of Hg was also estimated based on measurement data. Results indicated that the total deposition fluxes of most trace elements were higher in Northern coastal NJ compared to Southern coastal NJ, reflecting the differences in the source strengths of these element emissions between the two coastal regions. Dry deposition processes were more significant for common dust-derived elements, particularly Fe and Al, compared with their wet deposition fluxes. However, the processes of precipitation scavenging appeared to be more important for the elements that were often enriched in fine particles including Zn, Cu, Pb and Ni. The removal of Hg from the ambient air was overwhelmingly dominated by atmospheric wet deposition. In the future, atmospheric measurements at more sites on the NJ coast should be performed simultaneously to reduce the spatial and temporal uncertainties associated with atmospheric deposition fluxes estimated in this study.     

Marine Chemistry in the Coastal Environment: Principles,Perspective and Prospectus

Marine chemistry of the coastal environment starts with principles of rock weathering that use carbonic acid to mobilize elements, only some of which comprise the majority of sea salt. The principle reason is reverse weathering, extensively represented in coastal waters, and returns most elements to newly formed colloids or minerals while recycling carbon dioxide to the atmosphere. This includes the deeper ocean expanse of sediment diagenesis, plus hydrothermal plumes and attendant low-temperature basalt alteration. Within the estuarine and extended shelf regimes, both conservative and non-conservative processes can be distinguished and modeled to determine proportions of weathered elements transmitted to the sea or consumed by reverse weathering. Conceptually, the steady-state processes that lead to the composition of seawater can be viewed as heterogeneous equilibria between dissolved constituents and solid mineral products taking hundreds of millennia. However, initial processes in the estuarine and coastal environment are characterized by shorter term scavenging associated with inorganic and organic colloids. These recycle both carbon and trace elements on timescales commensurate with estuarine flushing and coastal exchange with the ocean. The natural uranium and thorium decay series provide powerful tools for quantifying the rates of estuarine processes, including those within groundwater and the subterranean estuary. In the future, new mass spectrometric and nuclear magnetic resonance techniques will help to define the molecular nature of newly formed estuarine colloids as has been done for dissolved organic matter. As the coastal environment undergoes the forces of climate change in the form of warming and sea level rise, future research should address how these will impact chemistry of the coastal environment as a net source or sink of carbon dioxide and associated organic material.     

Hierarchical simulation of aquifer heterogeneity: implications of different simulation settings on solute-transport modeling

The fine-scale heterogeneity of porous media affects the large-scale transport of solutes and contaminants in groundwater and it can be reproduced by means of several geostatistical simulation tools. However, including the available geological information in these tools is often cumbersome. A hierarchical simulation procedure based on a binary tree is proposed and tested on two real-world blocks of alluvial sediments, of a few cubic meters volume, that represent small-scale aquifer analogs. The procedure is implemented using the sequential indicator simulation, but it is so general that it can be adapted to various geostatistical simulation tools, improving their capability to incorporate geological information, i.e., the sedimentological and architectural characterization of heterogeneity. When compared with a standard sequential indicator approach on bi-dimensional simulations, in terms of proportions and connectivity indicators, the proposed procedure yields reliable results, closer to the reference observations. Different ensembles of three-dimensional simulations based on different hierarchical sequences are used to perform numerical experiments of conservative solute transport and to obtain ensembles of equivalent pore velocity and dispersion coefficient at the scale length of the blocks (meter). Their statistics are used to estimate the impact of the variability of the transport properties of the simulated blocks on contaminant transport modeled on bigger domains (hectometer). This is investigated with a one-dimensional transport modeling based on the Kolmogorov-Dmitriev theory of branching stochastic processes. Applying the proposed approach with diverse binary trees and different simulation settings provides a great flexibility, which is revealed by the differences in the breakthrough curves.