The landslides threatening Tasova town (Central Anatolia, Turkey) and their environmental impacts

There exist a number of landslides along the north Anatolian fault zone (NAFZ) between Tasova and Alparslan in Amasya province in Turkey. These landslides extending over an area of 2.5 × 6.0 km are triggered by steepening of slopes due to undercutting by the Yesilirmak River and groundwater fluctuations. The landslides have affected 30 buildings in the western part of Tasova. In this study, in order to investigate the engineering geological characteristics of the landslides and their environmental impacts, representative samples from geological units were collected and a total of six boreholes were drilled. Plastic pipes were installed into the boreholes to measure the groundwater fluctuations and to determine the position of the sliding surface. For a two-year monitoring period, using a GPS linked to a fixed station system, the magnitude of the movements ranged between 11.7 and 17.6 cm at the toe of landslide. The landslides that occurred in the study area were in the form of retrogressive circular and multiple circular failures. The factor of safety along a number of cross-sections calculated by the limit-equilibrium method of analysis is 0.96 in static condition. After further analyses, construction of a toe buttress with surface drainage may be suggested as a remedial measure to minimize the effects of these landslides.     

Sediment salt-load in the St Lucia Estuary during the severe drought of 2002–2006

The purpose of this study was to determine whether there was a sufficiently high residual salt load in the dry sediments of the St Lucia Estuary to cause salinity problems should it later fill up with either freshwater or seawater. The estuary lakes have suffered the effects of a severe drought since 2002 with the result that many areas were dry, and the salinity of the residual water varied between 4 psu and up to five times that of seawater. Measurements of the salts content in the sediments to a depth of 20 cm showed that more than 2 million tonnes of salt was held in this layer of the sediment in 2006. Recent management of the estuary (since 1970) has ensured that the mouth was not artificially opened. This was to prevent the inflow of seawater, with its salts, that would otherwise enter while the drought was in place. The results of the sediment salinity data showed that if the drought had been broken and the lake area filled with rain and river water, the resulting salinity would be about 6 psu. In March 2007, Cyclone Gamede in the Indian Ocean off the east coast of South Africa produced a wave climate at sea that resulted in the mouth breaching; thus introducing an estimated 12 million tonnes of salts. The high salinity in the system resulting from this breach is expected to have an adverse effect on the ecology of the system, whereas the residual salinity in the sediments would not have caused an environmental problem. If the estuary and lake system were to fill completely with seawater, the residual salts together with seawater will raise the salinity to an initial value higher than 40 psu, which will have the effect of suppressing much of the important submerged vegetation that is vital for sustaining juvenile fish in the system. Many of the large fauna will also suffer from a shortage of freshwater.     

Deciphering potential groundwater zone in hard rock through the application of GIS

Remote Sensing and Geographic Information System has become one of the leading tools in the field of hydrogeological science, which helps in assessing, monitoring and conserving groundwater resources. It allows manipulation and analysis of individual layer of spatial data. It is used for analysing and modelling the interrelationship between the layers. This paper mainly deals with the integrated approach of Remote Sensing and geographical information system (GIS) to delineate groundwater potential zones in hard rock terrain. The remotely sensed data at the scale of 1:50,000 and topographical information from available maps, have been used for the preparation of ground water prospective map by integrating geology, geomorphology, slope, drainage-density and lineaments map of the study area. Further, the data on yield of aquifer, as observed from existing bore wells in the area, has been used to validate the groundwater potential map. The final result depicts the favourable prospective zones in the study area and can be helpful in better planning and management of groundwater resources especially in hard rock terrains.     

A practical approach to grain shape quantification

Grain shape is a key factor affecting the mechanical properties of granular materials. However, grain shape quantification techniques to distinguish one granular material from another have not reached a stage of development for inclusion in modeling the behavior of granular materials. Part of the problem is the equipment of choice for grain shape measurement is the scanning electron microscopes. This is a relatively expensive and complex device. In this paper, we investigate a practical approach using light microscopy to quantify grain shape and to identify the key shape parameters that can distinguish grains. A light microscope was found to produce grain images with sufficient quality for the purpose of observing the grain shape profile. Several grain shape parameters were determined for eight different sands. We found Circularity, Roundness, Compactness, Sphericity, Aspect Ratio and ModRatio to be the key shape parameters that differentiate these sand grains.     

Discussion on “Experimental study on fracture toughness and tensile strength of a clay” [Engineering Geology 94 (2007) 64–75]

The paper [Wang, J.-J., Zhu, J.-G., Chiu, C.F., Zhang, H., 2007. Experimental study on fracture toughness and tensile strength of a clay. Engineering Geology 94, 64–75.] focuses on two important fracture parameters of soils: tensile strength and fracture toughness. These parameters control the behaviour of soils in a wide range of situations, from the design of a simple footing to much complicated fracture behaviour of clay liners or covers. The authors have done extensive laboratory work to determine these two parameters and their laborious and complicated experimental program needs praise. However, some of the points raised in their conclusions, based on the analysis and comparison with the data from the literature, need to be discussed.     

Diamond formation in sulfide pyrrhotite-carbon melts: Experiments at 6.0–7.1 GPa and application to natural conditions

Experiments at 6.0–7.1 GPa and 1500–1700°C were carried out to explore the boundary conditions of diamond nucleation and growth in pyrrhotite-carbon melt-solutions. Pyrrhotite is one of the main sulfide minerals of the pyrrhotite-pentlandite-chalcopyrite assemblage of mantle rocks and primary inclusions in diamond. Solutions of carbon in sulfide melts oversaturated with respect to diamond at the expense of the dissolution of starting graphite (thermodynamically unstable phase) are formed owing to the difference between the solubilities of graphite and diamond, which increases under the influence of temperature gradients in experimental samples. We determined the fields of carbon solutions in pyrrhotite melt showing labile and metastable oversaturation with respect to diamond, which correspond to the spontaneous nucleation of the diamond phase and diamond growth on seeds, respectively. The linear growth rate of diamond in sulfide-carbon melts is rather high (on average, 10 μ/min during the first 1–2 min from the onset of spontaneous crystallization). The nucleation density is estimated as 180 grains per cubic centimeter. Diamonds crystallized from sulfide melts show octahedral and spinel twin shapes. Diamond polycrystals were synthesized for the first time from a sulfide medium as intergrowths of skeletal (edge) or “cryptocrystalline” microdiamonds, from 1 to 100 μm in size, their spinel twins and, occasionally, polysynthetic (star-shaped) twins. During diamond growth from sulfidecarbon melts on smooth faces of cuboctahedral diamond seeds synthesized in metal systems, smooth-faced layer-by-layer step-like growth was observed on their octahedral (111) faces, whereas growth on the (100) cubic faces produced rough-surfaced layers of intergrown micropyramids, whose axes were oriented normal to the (100) face. The obtained experimental results were applied to the problem of diamond genesis under the conditions of the Earth’s mantle in the framework of the model of carbonate-silicate parental melts with blebs of immiscible sulfide melts.     

Water release patterns of heated speleothem calcite and hydrogen isotope composition of fluid inclusions

Speleothem fluid inclusions are a potential paleo-precipitation proxy to reconstruct past rainwater isotopic composition (δ¹⁸O, δD). To get a better insight in the extraction of inclusion water from heated speleothem calcite, we monitored the water released from crushed and uncrushed speleothem calcite, heated to 900 °C at a rate of 300 °C/h, with a quadrupole mass spectrometer. Crushed calcite released water in three not well individualised peaks between 25 and 360 °C, 360 and 650 °C and between 650 and 800 °C while uncrushed calcite released water in two distinct temperature intervals: between 25 and 550 °C and between 550 and 900 °C.Water from two speleothems from the Han-sur-Lesse cave was recovered using three different techniques: i) the crushing and heating to 360 °C technique, ii) the decrepitation by heating to 550 °C and iii) the decomposition by heating to 900 °C technique. Measurements of the δD of water recovered by the decomposition of Han-sur-Lesse calcite heated to 900 °C did not show a 20 to 30‰ offset as found by previous authors. However a difference of 7‰ was observed between water released before and after decomposition of the calcite. Water recovery from the Han-sur-Lesse samples suggests that a simple heating technique (up to 550 °C) without crushing could both (a) recover water with δD representative of that of the drip water and (b) double the water yield as compared to the crushing and heating method.Our study warns for possible contamination of the recovered inclusion water with hydration water of lime, responsible for the recovery of water with very negative δD values.     

THERIA_G: a software program to numerically model prograde garnet growth

We present the software program THERIA_G, which allows for numerical simulation of garnet growth in a given volume of rock along any pressure–temperature–time (P–T–t) path. THERIA_G assumes thermodynamic equilibrium between the garnet rim and the rock matrix during growth and accounts for component fractionation associated with garnet formation as well as for intracrystalline diffusion within garnet. In addition, THERIA_G keeps track of changes in the equilibrium phase relations, which occur during garnet growth along the specified P–T–t trajectory. This is accomplished by the combination of two major modules: a Gibbs free energy minimization routine is used to calculate equilibrium phase relations including the volume and composition of successive garnet growth increments as P and T and the effective bulk rock composition change. With the second module intragranular multi-component diffusion is modelled for spherical garnet geometry. THERIA_G allows to simulate the formation of an entire garnet population, the nucleation and growth history of which is specified via the garnet crystal size frequency distribution. Garnet growth simulations with THERIA_G produce compositional profiles for the garnet porphyroblasts of each size class of a population and full information on equilibrium phase assemblages for any point along the specified P–T–t trajectory. The results of garnet growth simulation can be used to infer the P–T–t path of metamorphism from the chemical zoning of garnet porphyroblasts. With a hypothetical example of garnet growth in a pelitic rock we demonstrate that it is essential for the interpretation of the chemical zoning of garnet to account for the combined effects of the thermodynamic conditions of garnet growth, the nucleation history and intracrystalline diffusion. Electronic supplementary material  The online version of this article (doi:) contains supplementary material, which is available to authorized users.

Assessing soil erosion in Mediterranean karst landscapes of Lebanon using remote sensing and GIS

Maps showing the potential for soil erosion at 1:100,000 scale are produced in a study area within Lebanon that can be used for evaluating erosion of Mediterranean karstic terrain with two different sets of impact factors built into an erosion model. The first set of factors is: soil erodibility, morphology, land cover/use and rainfall erosivity. The second is obtained by the first adding a fifth factor, rock infiltration. High infiltration can reflect high recharge, therefore decreasing the potential of surface runoff and hence the quantity of transported materials. Infiltration is derived as a function of lithology, lineament density, karstification and drainage density, all of which can be easily extracted from satellite imagery. The influence of these factors is assessed by a weight/rate approach sharing similarities between quantitative and qualitative methods and depending on pair-wise comparison matrix.The main outcome was the production of factorial maps and erosion susceptibility maps (scale 1:100,000). Spatial and attribute comparison of erosion maps indicates that the model that includes a measure of rock infiltration better represents erosion potential. Field investigation of rills and gullies shows 87.5% precision of the model with rock infiltration. This is 17.5% greater than the precision of the model without rock infiltration. These results indicate the necessity and importance of integrating information on infiltration of rock outcrops to assess soil erosion in Mediterranean karst landscapes.     

Evidence for crustal degassing of CF4 and SF6 in Mojave Desert groundwaters

Dissolved tetrafluoromethane (CF₄) and sulfur hexafluoride (SF₆) concentrations were measured in groundwater samples from the Eastern Morongo Basin (EMB) and Mojave River Basin (MRB) located in the southern Mojave Desert, California. Both CF₄ and SF₆ are supersaturated with respect to equilibrium with the preindustrial atmosphere at the recharge temperatures and elevations of the Mojave Desert. These observations provide the first in situ evidence for a flux of CF₄ from the lithosphere. A gradual basin-wide enhancement in dissolved CF₄ and SF₆ concentrations with groundwater age is consistent with release of these gases during weathering of the surrounding granitic alluvium. Dissolved CF₄ and SF₆ concentrations in these groundwaters also contain a deeper crustal component associated with a lithospheric flux entering the EMB and MRB through the underlying basement. The crustal flux of CF₄, but not of SF₆, is enhanced in the vicinity of local active fault systems due to release of crustal fluids during episodic fracture events driven by local tectonic activity. When fluxes of CF₄ and SF₆ into Mojave Desert groundwaters are extrapolated to the global scale they are consistent, within large uncertainties, with the fluxes required to sustain the preindustrial atmospheric abundances of CF₄ and SF₆.