基于TerrSolid对机载雷达DEM重提取方法研究

DEM的提取是激光雷达数据采集的重要用途之一,但由于目前算法的局限性,无法高精度地自动分类,如何在算法分类的基础上重新进行人工分类,以一定的原则和标准进行重提取从而得到更高精度的DEM,仍然是专业领域的一大难题。本文对某.LAS数据重提取,极大提高了其DEM的精度,为今后相关单位和个人使用TerrSolid软件对机载雷达DEM重提取提供一些经验。     

木本植被覆盖岸坡上波浪爬升过程的数值模拟研究

近岸木本植物构成的生态缓冲带作为新型的海岸软防护结构,兼具功能性和生态友好性,在沿海工程建设中愈发受到关注,如何深入开展其防护效果的机理研究是目前亟待解决的问题。本文采用数值模拟方法,在N-S方程中分别考虑树枝和树干的拖曳力影响,提出了木本植被作用下波浪沿斜坡爬升的表面波衰减的连续介质等效模型,并采用MAC法来跟踪自由曲面上的水颗粒轨迹。本文以波浪沿1/30的斜坡爬升为算例,对比讨论了有无植被作用下波浪的传播过程,并将算例结果与以往试验结果规律进行对照,验证了数值模型的有效性。最后,分别讨论了植物枝干的高度、密度、树枝倾斜角度等植被特性和波浪因素对植被消浪效果的影响,得到植被消浪的基本规律。文中的计算结果也可为实际的护岸工程和生态景观设计提供参考。     

基于拉格朗日拟序结构的吕宋海峡表层水交换研究

黑潮通过吕宋海峡入侵南海呈现明显的瞬态特征。以往的研究通常将黑潮在吕宋海峡附近的流态分为几种不同类型。本文基于表层地转流计算得到的有限时间李雅普诺夫指数场（FTLE）,展示了拉格朗日视角下的吕宋海峡上层水交换特征。从FTLE场提取的拉格朗日拟序结构（LCSs）很好地识别了吕宋海峡附近的典型流态和旋涡活动。此外,这些LCSs还揭示了吕宋海峡周围复杂的输运路径和流体域,这些特征得到了卫星跟踪浮标轨迹的验证,且从流速场中是无法直接识别的。FTLE场显示,吕宋海峡附近表层水体的输运形态主要可分为四类。其中,黑潮直接向北流动的“跨越”形态和顺时针旋转的“流套”形态的发生频次明显高于直接进入南海的黑潮分支“渗入”形态和南海水流出至太平洋的“外流”形态。本文还进一步分析了黑潮在吕宋海峡处的涡旋脱落事件,突出强调了LCSs在评估涡旋输运方面的重要性。反气旋涡旋的脱落个例表明,这些涡旋主要源自黑潮“流套”,涡旋脱落之前可有效地俘获黑潮水。LCS所指示的输运通道信息有助于预测最终被反气旋涡所挟卷水体在上游的位置。而在气旋涡的形成过程中,LCS的分布特征表明,大部分气旋涡并未与黑潮水的输运路径相连通。因此,气旋涡对从太平洋到南海的上层水交换的贡献较小。     

Analysis of resistance factors for LRFD of soil nail pullout limit state using default FHWA load and resistance models

Abstract

Resistance factors for load and resistance factor design (LRFD) of pullout limit state of both permanent and temporary soil nails are calibrated against a wide design space using the current Federal Highway Administration (FHWA) nail load and resistance models. The calculated resistance factors were shown to scatter broadly among design scenarios that differ in wall face batter, soil friction angle, nail ultimate bond strength, and surcharge live load. An important lesson learned from the analysis results is that the current practice of using a single resistance factor for LRFD of nail pullout limit state could not result in uniform reliabilities across different design scenarios. Simple artificial neural network (ANN) models were developed for computation of resistance factors. Design examples demonstrated the ability of the ANN models in providing resistance factors that yield satisfactory and consistent reliabilities in different nail pullout designs.     

Effect of different registration methods on precision of orientation based on RTK registration/georeferencing mode

Abstract

Compared with traditional methods, the three-dimensional laser-scanning (3D-LS) technique can efficiently acquire many high-quality geometric properties of rock discontinuities. In practice, engineers usually prefer to simplify the processing by using single-station point data and roughly orienting owing to the complexity of registration/georeferencing multi-station point data. However, prior published studies have paid little attention to the accuracy and reliability when determining discontinuity orientations using 3D-LS. We propose a reliable and accurate method with robust on-site applicability. As part of an ongoing effort, we are evaluating the precision of the commonly used coarse registration method and the fine registration method, and promoted the optimized coarse- and fine-registration methods and evaluated their precision. It is found that: (1) the common and the optimized registration method can meet our project’s engineering requirements, and the optimized registration method improved accuracy in the dip direction by approximately 1°; (2) fine registration using an iterative closest point (ICP) algorithm can correct both dip direction and dip angle; and (3) the orientation is of high precision with commonly used coarse and fine registration, whereas the optimization effect to correct the orientation is slightly limited.     

Dynamic characteristics of marine soft clay under variable phase difference and initial static shear stress

Abstract

Under seismic loading, the soil layer is subjected to multidirectional cyclic shear stress with different amplitudes and frequencies because of the coupling of multiple shear waves and the soil element within a slope or behind a retaining wall is subjected to initial static shear stress before subjected to cyclic loading. Due to the complexity of seismic loading propagation, a phase difference exists between the initial static shear stress and cyclic shear stress. To investigate the influence of the phase difference and initial static shear stress on cyclic shear strain, cyclic modulus, and cyclic strength, a series of laboratory tests are performed on Wenzhou marine soft clay by multi-directional simple shear system, which can simulate the actual state better by controlling the horizontal cyclic stress in the x and y directions simultaneously. As the phase difference varies from 0° to 90°, the dynamic shear modulus increases and cyclic strain accumulation decreases with an increasing number of cycles. The shear strain increases with the initial shear stress.     

基于蛇模型的等深线化简质量定量调控方法

针对当前等深线的化简过程未考虑化简后等深线质量的问题,以基于蛇模型的等深线化简方法为基础,引入航海图等深线化简质量的定量评估方法,对化简后等深线的质量进行定量评估,并将评估结果作为蛇模型算法的总能量,实现了等深线化简过程的定量调控,提出了基于蛇模型的等深线化简质量定量调控方法。实验结果表明:该方法能够根据等深线的化简质量定量调控等深线的化简过程,不仅能够提高航海图等深线的化简质量,而且为后续等深线化简算法的研究提供了新的思路。     

中国大陆结构地震反应观测系统布设研究

本文简要介绍了结构地震反应观测研究的意义。并以中国地震局防灾大楼和北京市人大办公大楼结构地震反应观测系统为布设实例,阐述了中国大陆地区结构地震反应观测系统的两种布设方式。对两种方式进行了分析,指出简化布设中存在的问题,并提出了布设原则,用于指导结构地震反应观测系统的布设。     

尺度政治视角下的新安江流域生态补偿政府主体博弈

流域生态补偿是中国跨区域生态治理和自然区域保护的一项重要经济、社会、环境政策,涉及区域利益主体权益差异与协调、区域生态协同发展和合作模式构建等方面,是一个典型的地理学研究命题。本文将制度粘性引入到尺度政治理论中,剖析新安江流域生态补偿政府主体的博弈行为,探究不同政府主体的博弈特征和博弈机制。结果表明:中央政府、省级政府、市级政府等不同层级政府主体经历了竞争博弈、合作博弈和竞合博弈3个阶段,构建政府利益共同体能够推进流域生态补偿建设,中央政府的“适度介入”是开展跨省流域生态补偿的关键;流域生态补偿制度从“垂直”模式向“垂直—水平”模式的变迁过程中存在明显的制度粘性,政府主体利用政策革新和社会参与等制度约束稀释制度粘性,重塑流域生态补偿制度;尺度转换是推动新安江流域生态补偿的核心机制,政府主体通过重新分配权力和资本、嵌入非正式约束塑造流域生态补偿话语体系,推动新安江流域生态补偿由“强国家—弱社会”向“强国家—强社会”结构模式的转变。研究结果能够为构建跨区域流域生态补偿机制提供理论支撑,为合理评价和指导流域生态补偿实践、促进流域经济社会协调可持续发展提供科学依据。     

Influence of Stress on Void Ratios of Compacted Crushed Rock Masses in Coal Mine Gobs

The transfer and evolution of stress among rock blocks directly change the void ratios of crushed rock masses and affect the flow of methane in coal mine gobs. In this study, a Lagrange framework and a discrete element method, along with the soft-sphere model and EDEM numerical software, were used. The compaction processes of rock blocks with diameters of 0.6, 0.8, and 1.0 m were simulated with the degrees of compression set at 0%, 5%, 10%, 15%, 20%, and 25%. This study examines the influence of stress on void ratios of compacted crushed rock masses in coal mine gobs. The results showed that stress was mainly transmitted downward through strong force chains. As the degree of compression increased, the strong force chains extended downward, which resulted in the stress at the upper rock mass to become significantly higher than that at the lower rock mass. It was determined that under different degrees of compression, the rock mass of coal mine gobs could be divided, from the bottom to the top, into a lower insufficient compression zone (ICZ) and an upper sufficient compression zone (SCZ). From bottom to top, the void ratios in the ICZ sharply decreased and those in the SCZ slowly decreased. Void ratios in the ICZ were 1.2–1.7 times higher than those in the SCZ.