Identification des anomalies magnétiques sur les dorsales à faible taux d'expansion: Méthode des taux fictifs

The fit between calculated and observed magnetic anomalies from slow-spreading centers is improved when allowing for a transition zone between two inversely magnetized blocks. In this paper it is shown that these models are very easily computed by choosing a fictitious spreading rate which is slower than the real spreading rate and by changing the distance scale appropriately. With these slow fictitious spreading rates, the models are very sensitive to the relative position of the successive inversions and could be used to adjust these positions in the magnetic time scales.     

Optimal placement of dampers and actuators based on stochastic approach

A general method is developed for optimal application of dampers and actuators by installing them at optimal location on seismic-resistant structures. The study includes development of a statistical criterion, formulation of a general optimization problem and establishment of a solution procedure. Numerical analysis of the seismic response in time-history of controlled structures is used to verify the proposed method for optimal device application and to demonstrate the effectiveness of seismic response control with optimal device location. This study shows that the proposed method for the optimal device application is simple and general, and that the optimally applied dampers and actuators are very efficient for seismic response reduction.     

Pseudodynamic tests on rubber base isolators with numerical substructuring of the superstructure and strain‐rate effect compensation

A pseudodynamic testing procedure has been applied by which the seismic response of a base‐isolated building is obtained by using as specimen the isolators, while the superstructure is numerically simulated. The procedure also takes advantage of the continuous pseudodynamic testing capabilities of the ELSA laboratory, which increase the accuracy of the results and reduce the strain‐rate effect of the rubber bearings. A simple proportional correction of the measured forces compensates the remaining strain‐rate effect due to the unrealistic speed of the test. The correction factor is obtained by means of a characterizing test on the specific rubber isolators. The developed method has been successfully applied to the prediction of the seismic response of a base‐isolated four‐storey building submitted to several specified accelerograms. The results for those earthquakes as well as the effects of some changes of the parameters of the system are discussed. Copyright © 2002 John Wiley & Sons, Ltd.     

The removal of color and COD from wastewater containing water base color by coagulation process

In this study acrylic water base color was removed from synthetic wastewater using coagulation process. Experiments were conducted on the sample containing 100 mg/L and 400 mg/L of acrylic water base color. Destruction of color by means of coagulation/flocculation techniques using ferrous sulfate, alum, lime and polyelectrolyte (cationic, anionic and non ionic). The study was performed in a systematic approach searching optimum values of alum and FeSO₄ concentration, pH and temperature. All the experiments were run in a laboratory scale.The obtained results show that treatment with alum and ferrous sulfate alone proved to be very effective in removing the color (> 99 %) and part of COD (60–70 %) from aqueous solution. Lime alone did not significant change on COD and color removal.     

Controlling factors on the morphology and spatial distribution of methane-related tubular concretions – Case study of an Early Eocene seep system

Up to 10 m in length and >1 m in diameter tubular, calcite-cemented sandstone concretions are hosted by the faulted Dikilitash unconsolidated sands and sandstones. These structures document shallow subsurface pathways of Early Eocene methane seepage in the Balkan Mountains foreland (NE Bulgaria). Their exceptional exposure allowed a unique study of the factors governing the morphology and spatial distribution of such fossilized fluid conduits. The large dimensions and subvertical, cylindrical shape of the most common tube type primarily reflects the buoyancy-driven, vertical path of an ascending gas-bearing fluid through permeable, mainly unconsolidated sandy host sediments. Tube morphology was also influenced by local stratigraphic anisotropies and might as well document differences in former seepage conditions. Mapping of >800 tubular concretions showed the NNW–NNE elongation and alignment of tube clusters and massive cemented sandstone structures. This suggests that Paleogene fault systems played a major role in directing the movement of fluids. However, within a single tube cluster, tubes are preferentially aligned, over distances up to 50 m along directions at an angle between 10° and 36° with respect to the inferred NNW–NNE, cluster parallel fault traces. In addition, cylindrical tubes of analogue dimensions are aligned over distances >100 m along N15° to N25°-oriented directions. It is hypothesized that this spatial geometry of tubular concretions reflects the complex geometry of deformations structures in fault damage zones along which fluids were preferentially channelled.     

Identification of perylene in sediments: Occurrence and diagenetic evolution

Perylene and penta-aromatic hydrocarbons were determined in sediments as part of a study that was dedicated to the aquatic ecosystem of Elelenwo Creek (Southern Nigeria) in order to carry out a critical corroboration of occurrence and diagenetic evolution of perylene in the sediments of the creek. The results show that the annual mean levels of Benzo [g, h, i] Perylene ranged from 209.00–245.28 ?g/kg dry weight at the various stations sampled. Meanwhile, Station 3 recorded the highest mean level of 245.28 ?g/kg dry weight. The observed values for total penta-aromatic hydrocarbons were high (787.00–1154.36?g/kg dry weight) in all the stations sampled. In addition, the highest mean value of 1154.36?g/kg dry weight was again recorded at station 3 for the penta-aromatic hydrocarbons. One origin index or concentration ratio of Ip/Ip+BghiP was also used to evaluate the suitability of the penta-aromatic hydrocarbons as a tracer to distinguish between contaminations arising from different sources. The values for the sampling stations therefore ranged from 0.41 to 0.43. A critical appraisal of the PAH index, consequently, suggested that petroleum combustion is the major penta-aromatic hydrocarbon source in sediments of the creek. The PAH group profile shows that perylene was high in the sediments and would pose apparent effects in fauna. The high concentration of perylene in the sediments was also indicative of an in situ biogenic derivation. Furthermore, a concentration of perylene > 10 % of total penta-aromatic hydrocarbons established a credible diagenetic origin.     

Effect of trace metals on halophilic and mixed cultures in anaerobic treatment

Trace metals are known to stimulate the activity of anaerobic methanogenic bacteria involved in the degradation of organic matter. The objective of this research was to investigate the effect of three trace metals, iron, nickel and cobalt on the activity of halophilic methanogens, digester sludge and a mixed culture of halophilic bacteria and digester sludge, at various salt concentrations. Iron slightly stimulated both initial and maximum specific methanogenic activity (SMA) of halophilic methanogens at all salt concentrations. Iron addition was also able to increase both initial and maximum SMA of the mixed culture. Iron could not stimulate either initial or maximum SMA of digester sludge at salt concentrations of more than 10 g/L. Adding cobalt showed no benefit on the initial and maximum SMA of halophilic methanogens. A slight increase in the initial SMA was observed in mixed culture when cobalt was injected to the system containing sodium concentrations of 10–30 g/L. At salt concentrations above 40 g/L, cobalt could stimulate the maximum SMA of mixed culture. No benefits were found when cobalt was added to the digester sludge at sodium concentrations higher than 20 g/L. Nickel was observed to increase the initial SMA of digester sludge at all salt concentrations, and the maximum SMA of mixed culture at salt concentrations of 30–50 g/L.