A Computational Model for Velocity Separation in Shallow Sea

Based on the hydrodynamical feature and the theoretical velocity profiles of tidal flow and vvind-induced flow in shal-low sea, a computational model is established for the first time, which can separate observed velocity into tidal velocity and wind-induced velocity by use of the least square method. With the model, not only the surface velocities of tidal flow and vvind-induced flow are obtained, but also the bed roughness height is determined and the wind velocity above the wa-ter surface is estimated. For verification of the model, the observed velocity in the Yellow River Estuary and the laborato-ry test is separated, then it is applied to the Yangtze River Estuary. All the results are satisfactory. The research results show that the model is simple in method, feasible in process and reasonable in result. The model is a valid approach to analysis and computation of field dala, and can be applied to separate the observed velocity in shallow sea; at the same time, reasonable boundary conditions of th     

Wave Loads and Protective Techniques of An On-Shore Wave Power Device

In this paper, the extreme wave loads on an on-shore wave power device are investigated. First, boundary element method is applied to solve the three dimensional potential problem based on the small amplitude wave assumption. Then the motion of the Oscillating Water Column (OWC) inside the device and its laods on the device are calculated in time domain. Several protective techniques often applied are simulated by changing the constraint of the upper end of the chamber of the device. Numerical results are used to judge the effectiveness of these techniques. The investigation shows that damping can not effectively restrain the motion of OWC when the period of incident wave is long, which may cause dangerous loads on the structure. The shut chamber can effectively restrain the motion of OWC, but alternatively cause high pressure in the chamber. A Contracting opening with a Taper (CT) can exhaust a great amount of kinetic energy of OWC, and significantly decrease the loads. It is a promising protective tec     

Numerical Analysis of Wave Forces on Arbitrarily Shaped Multi-Pillars Over Varying Topography

The modified hybrid element method (MHEM) is utilized to predict and analyze wave forces on arbitrarily shaped multiple bodies. This method can be applied to waves of all water depths, i. e. shallow, intermediate, and deep waters, on slowly varying seabed. The MHEM employs the ICCG method to save CPU and storage, thus the computation of wave forces for large multi-body systems can be carried out on microcomputers. Numerical results of the present method are compared with experimental data and other solutions. It is shown that the MHEM provides more accurate solutions of the wave forces than other numerical methods do. Therefore, the methodology presented herein can be used in the design of coastal and ocean structures.     

分潮波模型多资料数值计算方法研究 Ⅱ.有限差分最小二乘方法

对含多资料的分潮波模型的超定问题进行探讨，建立一种有限差分—最小二乘方法，该方法使得岸边资料直接进入了计算方程，并保证岸界法向流速为零条件。通过对渤海的四大分潮的试算，证实本方法可行。     

Wave-Current Forces on Small Square Cylinders (Part I)

-Based on the extended Morison Equation and model tests, the in-line forces on small square cylinders caused by waves (regular and irregular) and currents are analyzed in detail in this paper. The hydrodynamic coefficient CD and Cu related to KC number and the effect of direction of wave incidence are also given, which can be used in engineering practice.     

Model Test of Sand Restraining Force on Pipeline

This paper describes the model tests for determining the axial friction and the lateral resistance of sand to pipeline by using fine sand and prototype pipeline, and the calculation method based on limit analysis theory is verified. The effect of cyclic loading is considered in the test.     

Shear Failure of a Clamped Dented Tubular Beam Under Lateral Impact

- The shear failure of a rigid-plastic dented clamped tubular beam under the lateral impact of a mass is investigated. Both the denting and the impact point are in the middle span of the beam. It is assumed that denting does not spread during the shear sliding. Numerical results show that the axial force and lateral deflection of the beam are very small at the moment of the occurence of shear failure, which means that the finite deformation effect can be neglected in the shear failure analysis. Also, some aspects of the initial impact energy are investigated.     

Optimal Design for Main Dimensions of a 75000t Floating Production and Storage Vessel

The basis, process and results of the demonstration of the main dimensions of a 75000t floating production and storage vessel are discussed in this paper. A simple but reliable orthogonal design method is applied in the main dimension optimization. The ideas of gradual approximation and feedback from various aspects are put into effect. During the demonstration, in order to make the model tally with the actual situation, the draft design is closely related to the computational analysis, so that the demonstration model can be verified at any time; the handling of the overall system is closely related to the research of each item, which is beneficial not only to the mastery of various regularities, but also to the balance of decisions. Finally, according to the computational results and the regularities obtained from analysis, the main dimensions are determined.     

Dynamic Analysis of a Single-Column Platform (II)

This paper describes the study of a single-column structure used as well-head platform. In order to check the reliability of computation theory and programme, model tests have been carried out. The paper introduces the conclusion of tests and the dynamic properties of single-column platform are obtained.     

Elasto-Plastic Analysis of Tubular Joints of Offshore Platforms by Finite Element Method

The plastic node method is reformulated by the variational principle and is applied to elasto-plastic finite element analysis of tubular joints, eventually including the effect of internal and external gussets, stiffener rings, etc., if necessary. Four different joints are studied here in detail for the elasto-plastic behavior, the strain at the hot spot, the strain concentration factor around the intersection line, and the propagation of the plastic region with loading up to collapse in order to determine the ultimate strength, safety factor, and development of the plastic field. The present results are in good agreement with the experimental results.