Detailed architecture of a compound incised valley system and correlation with forced regressive wedges: Example of Late Quaternary Têt and Agly rivers,western Gulf of Lions,Mediterranean Sea,France

Quaternary incised valley systems are usually characterized by the preservation of a single valley-fill attributed to the last post-glacial period. Moreover, there are very few cases of correlation between incised valley system developed on inner shelf and sedimentary units observed on the mid to outer shelf, mainly forced regressive wedges. The Roussillon shelf, in the western part of the Gulf of Lion, is a particular example of preserved Quaternary compound incised valley system also characterized by a direct correlation with the forced regressive lowstand wedges on the mid-outer shelf. High-resolution seismic data and a borehole, 60 m deep, located on the beach barrier permit an accurate study of the geometry and lithology of the system. Six imbricated and more or less preserved incised valleys and valley-fills are observed up to the inner to mid-shelf. The key surfaces associated to the incised valleys are correlated to the boundaries of the forced regressive wedges. They are assumed to be reworked surfaces. At the borehole location, only few thin layers, less than 1 m thick, of coarse grain and/or floating pebbles, are observed and should correspond to preserved fluvial lowstand deposits reworked under marine influence. The valley fills are mainly composed of estuarine muddy silts. From AMS ¹⁴C age dating it is inferred that the uppermost incised valley system is younger than 45 ky cal BP. Based on those observations, the six preserved incised valley systems are assumed to be controlled by the last six 4th order sea-level cycles — 100 ky — of the middle to late Quaternary. The paleo-topography of the underlying Plio-Quaternary deposits controls the compound incised valley system location. The deep topography of the Messinian Erosionnal Surface is a controlling factor at a lower degree. The partial preservation of the successive valley fill is attributed not only to the differential subsidence but also to the lateral migration of each incision and to the hydrodynamic regime.     

Effect of Soil Parameters on Dynamic Cone Penetration Indices of Laterite Sub-grade Soils from India

The focus of this study was on correlating the effect of grain-size, maximum dry-density (MDD), field moisture content, and the void ratios on penetration measured using the dynamic cone penetrometer (DCP) for laterite soils blended with fines. Tests were performed on soil samples compacted to MDD for moulding water contents set to the optimum moisture content (OMC), dry of OMC, and wet of OMC un-soaked condition. The results indicated that an increase in the fines-content caused a decrease in the MDD, and an increase in the OMC and the DCP penetration. Regressions were developed correlating various parameters.     

Geoecological investigations of the Ob-Irtysh River Basin in the Khanty-Mansi Autonomous region: Yugra in 2006–2007

This paper reports the results of the investigations of 2006–2007 on the distribution and migration forms of artificial radionuclides and chemical elements in the Ob-Irtysh water system. Three regions were studied. One of them is a local segment of the Ob River upstream from the confluence with the Irtysh River; its investigation allowed us to estimate the general radioecological state of the aquatic environment affected by the activity of the Tomsk 7 plant. The second region is a local segment of the Irtysh River upstream from its confluence with the Ob River, where the influence of emissions from the NPO Mayak could be estimated. The third region is the water area of the Ob River after its confluence with the Irtysh River. It characterizes the real level of radioactive and chemical contamination of the middle reaches of the Ob River.In order to explain horizontal variations in the distribution of radionuclides in the upper layer of bottom sediments collected at various sites, the results of sorption-kinetic experiments with radioactive tracers in the precipitate-solution system were used. The investigation of the migration forms of trace elements and radionuclides occurring in river water was based on the method of tangential-flow membrane filtration.Chemical element contents were determined in 400-ml water samples. A set of Millipore polysulfone membranes with pore sizes of 8, 1.2, 0.45, 0.1, and 0.025 μm was employed. Taking into account the ultralow specific concentrations of radionuclides in the water, they were analyzed in 300–500 litre samples using Millipore polysulfone membranes with pore sizes of 0.45 μm and 15 kDa. This allowed us to estimate the percentages of cesium-137 and plutonium-239, 240 in the suspended particulate fraction, colloids, and dissolved species.     

XMCD at Fe L<Subscript>2,3</Subscript> edges,Fe and S K edges on Fe<Subscript>7</Subscript>S<Subscript>8</Subscript>

Pyrrhotite (Fe₇S₈) is a natural iron sulphide that can participate in rock magnetisation. Its electronic structure is not yet surely described. X-ray magnetic circular dichroism (XMCD) at Fe L_2,3 edges on Fe₇S₈, coupled with multiplet calculations, shows that iron is present only as Fe²⁺ in this magnetic iron sulphide. It reveals a strong magnetic orbital moment. XMCD at Fe and S K edges shows the quite strong polarization of both Fe and S in Fe₇S₈.     

Wave climate in a groin field

Wave records at seven different locations within a groin field have been analysed by both statistical and spectral approaches to study the general wave climate. The wave heights and periods from the wave records were obtained by both upcross and downcross methods for the statistical approach. The variation of different wave height and wave period parameters with respect to the time of measurement at a particular location and its variation at different locations within the groin field at a particular instant of time are presented and discussed in detail in this paper. It is generally found that the wave heights follow the Weibull distribution.     

Weak GPS signal tracking using FFT discriminator in open loop receiver

An open loop tracking architecture, which tracks GPS signals under weak and challenging conditions, is analyzed. The in-phase and quadrature-phase integration pair is regarded as a single tone complex signal. An FFT-based method is used as a frequency discriminator to estimate the Doppler frequency residual of the single tone signal. Another FFT-based method applies complex squaring to eliminate the effect of the navigation data bits polarities. The performance of the FFT-based discriminators is assessed in three criteria. Those criteria are the signal strength and dynamic range that can be tracked and the accuracy of the estimated Doppler frequency. In addition, the performance of the discriminators is analyzed to provide the theoretical and simulated peak detection probability. The results indicate that the FFT discriminator can track signals about 5 dB weaker than the signals that can be tracked by the complex squared FFT discriminator. In a quasi-static environment, the Doppler frequency residual can be assumed to be around zero, which can enable the FFT-based discriminators to track signals with approximately 2 dB less power. Moreover, the performance of the FFT-based discriminators is compared with the performance of two other frequency discriminators, namely the fast–slow and power-based. The comparison results indicate that these two frequency discriminators give higher frequency estimation accuracy, but they have a narrower dynamic range.     

Seismic profile analysis of the Kangra and Dehradun re-entrant of NW Himalayan Foreland thrust belt,India: A new approach to delineate subsurface geometry

In the NW Sub-Himalayan frontal thrust belt in India, seismic interpretation of subsurface geometry of the Kangra and Dehradun re-entrant mismatch with the previously proposed models. These procedures lack direct quantitative measurement on the seismic profile required for subsurface structural architecture. Here we use a predictive angular function for establishing quantitative geometric relationships between fault and fold shapes with ‘Distance–displacement method’ (D–d method). It is a prognostic straightforward mechanism to probe the possible structural network from a seismic profile. Two seismic profiles Kangra-2 and Kangra-4 of Kangra re-entrant, Himachal Pradesh (India), are investigated for the fault-related folds associated with the Balh and Paror anticlines. For Paror anticline, the final cut-off angle \(\beta =35{^{\circ }}\) was obtained by transforming the seismic time profile into depth profile to corroborate the interpreted structures. Also, the estimated shortening along the Jawalamukhi Thrust and Jhor Fault, lying between the Himalayan Frontal Thrust (HFT) and the Main Boundary Thrust (MBT) in the frontal fold-thrust belt, were found to be 6.06 and 0.25 km, respectively. Lastly, the geometric method of fold-fault relationship has been exercised to document the existence of a fault-bend fold above the Himalayan Frontal Thrust (HFT). Measurement of shortening along the fault plane is employed as an ancillary tool to prove the multi-bending geometry of the blind thrust of the Dehradun re-entrant.     

Experimental study on the instability mechanism of the major-defect fractured rock

Based on calculations of rock fracture surface and angle, incremental-load creep experiments were conducted on two groups of major-defect fractured rock specimens in an RLW-2000 rheology test system. The research investigated the fracture type and the creep properties of major-defect fractured rock and analyzed the relationships between failure load and horizontal or vertical projection distance, and between each of theme and fracture area or angle. The results showed that rock fracture was divided into three types according to the distribution, including I, II, and III types. I, II, and III types were respectively an internal fracture running through neither the upper nor lower end, one through the upper or lower end and one through both upper and lower ends, and a III type was further sub-divided into III_I and III_II types. The instantaneous strain was larger than the creep strain under the same creep loading stage. As the creep loading increased on two groups of major-defect fractured rock, the instantaneous strain decreased abruptly and then increased abruptly, while the creep strain decreased rapidly at first and later increased near-linearly. When the failure angle was larger than the friction angle, failure load was positively correlated with failure angle yet was negatively correlated with vertical projection distance. Vertical projection distance and fracture angle, which decided fracture type, controlled rock failure load. Failure load increased in turn from I type to III type, and low-type fracture determined mainly failure load in multiply-fracture specimen.     

Wavefield analysis of crosswell seismic data

Despite the numerous advantages of crosswell seismic data over surface seismic data, crosswell seismic geophysics is still underutilized and underdeveloped. The factors limiting the full utilization of crosswell data include the lack of standardized methods for processing and imaging the data. This is because crosswell data is not completely understood. To improve the understanding of crosswell data, we performed acoustic and elastic modeling of a west Texas carbonate oilfield data using finite difference methods and crosswell geometry. To account for the different wave modes in the field data, we decomposed the full data into its constituent wave modes. Results of the forward modeling show that elastic synthetic data is a better representation of crosswell field data than the popular acoustic synthetic data. Wavefield decomposition gave insight into the time-space kinematics behavior of the different wave modes that constitute the full data. Overall, the study improved our understanding of crosswell field data. The learning from this study has been utilized to perform data-driven reflection enhancement processing where the discerned characteristic of different seismic arrival is utilize to suppress unwanted and enhanced the desired wave modes. The processing reduced the complex data to only up-going P-P reflections that can be imaged to reveal the subtle geological structures of the oilfield.