Microseismic events enhancement and detection in sensor arrays using autocorrelation‐based filtering

Passive microseismic data are commonly buried in noise, which presents a significant challenge for signal detection and recovery. For recordings from a surface sensor array where each trace contains a time‐delayed arrival from the event, we propose an autocorrelation‐based stacking method that designs a denoising filter from all the traces, as well as a multi‐channel detection scheme. This approach circumvents the issue of time aligning the traces prior to stacking because every trace's autocorrelation is centred at zero in the lag domain. The effect of white noise is concentrated near zero lag; thus, the filter design requires a predictable adjustment of the zero‐lag value. Truncation of the autocorrelation is employed to smooth the impulse response of the denoising filter. In order to extend the applicability of the algorithm, we also propose a noise prewhitening scheme that addresses cases with coloured noise. The simplicity and robustness of this method are validated with synthetic and real seismic traces.     

Comparative Assessment of Sludge Pre‐Treatment Techniques to Enhance Sludge Dewaterability and Biogas Production

Effectiveness of ultrasonication, microwave technologies, and enzyme addition prior to anaerobic digestion is investigated using sludge samples taken from the secondary settling tank of a domestic wastewater treatment plant to improve methane production, enhance dewaterability characteristics of the sludge, and to reduce excess sludge. Microwave pre‐treatment (1500 W, 10 min at 175 °C) results in better extra digester performance (compared to the control reactor) in terms of methane production (25 m³ ton^?1 suspended solids (SS)) than ultrasound (no improvement) and enzyme pre‐treatment (11 m³ ton^?1 SS). While methane production is not improved as a result of ultrasonication pre‐treatment (15 000 kJ kg^?1 SS), a noticeable increase (19%) is observed in the case of microwave pre‐treatment. Higher compactibility values are obtained after ultrasonication and microwave application compared to the control (i.e., from 7.1 to 8.7 and 9.2%, respectively) before anaerobic digestion. Although ultrasonication and microwave application decrease the dewaterability of the raw sludge (capillary suction time (CST) from 827 to 1364 and 2290 s, respectively), similar dewaterability results are obtained at the end of the anaerobic digestion process for all pre‐treated sludge samples. An economic assessment of this study shows that pre‐treatment with microwave results in more than 10‐fold less net cost compared to the enzyme application.     

Types and nature of fracture associated with Late Ordovician paleochannels of glaciofluvial Sarah Formation,Qasim region,Central Saudi Arabia

This study evaluates the Late Ordovician glaciofluvial deposits of the Sarah Formation and equivalent outcroppings in north, central, and southwestern Saudi Arabia. The Sarah Formation also covers a wide area in the subsurface and is considered as an important target for unconventional tight gas reservoir. Defining the fracture types, nature, and distribution in outcrop scale might help to establish a successful fracture simulation model and behavior for the Sarah tight gas reservoir in the subsurface. This study investigates fracture characteristics for the Sarah Formation at Sarah paleochannel outcrops. The study revealed three sets of fractures, which have EW, NS, and SE-NW directions, and these fractures vary from open, resistive, and filled to resistive fractures. The closed fractures are filled with ferruginated iron oxides and gypsum. The filled fractures (the thrust boundary) are found in the study area at the SE-NW strike fracture set, while open and resistive fractures are found mainly at S-N and E-W fracture sets, respectively. The syn-depositional filled fractures (iron oxides) are considered as the younger fracture sets while the open and resistive fractures are post-depositional fractures which may have resulted from uplift or tectonic movement. A general model representing the fracture pattern and the thrusting boundaries due to glacial movement was constructed. It has been noticed that the systematic occurrence of filled fractures (thrust boundaries) described the boundaries between different glacial events, which act as a fluid barrier (filled fractures) and decrease the reservoir quality. The finding of this study might be utilized as a guide and lead for exploration in the subsurface Sarah glacial deposits. It will also help to understand and speculate the nature pattern and distribution of fractures with the Sarah Formation.     

Composition,radioactivity, and possible applications of kaolin deposits of Sinai,Egypt

This work discusses the composition, radioactivity, and possible utilization of the kaolin resources in Sinai which are hosted in thick sandstone sequences belonging to the Carboniferous (Wadi Khaboba) and Early Cretaceous (Wadi Iseila and Abansakar) ages. The characterization of kaolin was done by microscopic and SEM examination, supported by XRD and ICP-MS analyses. The studied kaolin resources consist of kaolinite, as the main constituent, associated with subsidiary dickite and halloysite, and minor contribution of smectite and illite. The most dominant non-clay mineral is quartz, besides minor gypsum, dolomite, and hematite. Ferrugination dominates, in most cases, at the upper boundaries of the kaolin lenses, suggesting possible supergene activity. The high Al₂O₃/SiO₂ ratio for the Cretaceous kaolin (0.54, in average) specifies its better grade relative to the Carboniferous kaolin (0.43, in average). The kaolin of the middle part of lens C in Wadi Iseila contains Si/Al molecular ratio of about unity, suggesting high-grade kaolin. The Carboniferous kaolin has enriched the radionuclides: U, Th, and Ra (at disequilibrium state due to leaching of eU relative to Ra) and the REE, relative to that of the Cretaceous age. The Carboniferous kaolin is characterized by a higher contribution of HREE (zircon signature), whereas LREE seems to be more influential for the Early Cretaceous kaolin (monazite signature). In spite of the very high CIA index (93 to 99), none of the analyzed kaolin deposits displays Ce abnormality. The high radioactivity of some Carboniferous kaolin can be a serious impediment for its utilization or its exportation. The kaolin of Sinai does not satisfy the international standards for paperwork industries and refractory manufacturing, but beneficiation may overcome this challenge. However, some lenses have high-grade kaolin with a low percentage of oxides of iron, magnesium, calcium, sodium, and potassium and a low radioactivity, hence nominated for the local refractory industry. The high-grade kaolin of Sinai fulfills the standards required for ceramics manufacturing in the global market. Grade 3 kaolin (< 30%, Al₂O₃) can be used in the manufacturing of white Portland cement and red glaze manufacturing on both local and global markets.     

Sedimentology and facies analysis of Miocene mixed siliciclastic–carbonate deposits of the Dam Formation in Al Lidam area,eastern Saudi Arabia

The Burdigalian mixed siliciclastic–carbonate deposits of the Dam Formation are well-exposed in Al Lidam area, in the eastern province of Saudi Arabia. They represent a shallow part of the Arabian plate continental margin. The Dam Formation is correlatable to the Miocene reservoirs in both Iran and Iraq. Therefore, studying the Dam Formation lithologic heterogeneity in a small distance with high resolution could help in further work related to pattern prediction of the Miocene reservoir properties. High-resolution sedimentological investigation was carried out through six outcrops. The facies parameters (lithology, sedimentary structures, main fossils, paleocurrent patterns and geometries of the sedimentary bodies) were described. The results revealed 15 lithofacies that have been further grouped into 7 lithofacies associations 5 of which are carbonates and include (1) interbedded dolostone and evaporates, (2) microbialite buildup, (3) ooid-dominated grainstones, (4) burrowed skeletal peloidal wackestone–packstone and (5) mollusc-dominated wackestone–packstone. The remaining two associations are of siliciclastics and include (6) intertidal siliciclastics and (7) wave-dominated siliciclastics. These lithofacies were interpreted to reflect deposition in a mixed siliciclastic–carbonate ramp system that includes subtidal, shoreface, intertidal, foreshore, supratidal and estuarine deposits in a shallowing-upward succession. Each one of these lithofacies association has distinct geometry and architecture pattern. Oolites and heterozoan lithofacies occur as sheets and show great continuity along the strike direction. Oolites pass laterally in the dip direction into more skeletal- and peloid-dominated zones, whereas heterozoan lithofacies stay continuous in the dip directions and change from siliciclastic to carbonate heterozones. In contrast, microbialite lithofacies lack continuous beds and occur as localised bioherms and biostroms. Channelised lithofacies are restricted laterally into isolated channel bodies and vertically in the contact boundary between siliciclastic and carbonate lithofacies, whereas the interbedded dolostone and evaporite lithofacies form distinct, relatively thick continuous layers. With continuous exposures in both strike (1.2 km) and dip (0.15 km) directions, the outcrops in the Al Lidam area provide unique opportunity to study the heterogeneity among lithofacies of the mixed siliciclastic–carbonate system of the Dam Formation. Such study may provide insights to predict occurrence and distribution of lithofacies bodies in their equivalent reservoirs which are important for reservoir characterisation.     

Groundwater modeling in semiarid Central Sudan: adequacy and long-term abstraction

The present study assesses groundwater resources in the semiarid central Sudan, where 20 deep productive wells were installed to supply a major city in the region, El Obeid. The wells, which has an average 20 L/s discharge each, are taping a deep semiconfined to confined aquifer of fluvial silisiclastics deposited in the Tertiary–Pleistocene. Groundwater modeling was used as a technique to interpret the hydrologic system in arid to semiarid central Sudan and to simulate the future influence of the project on the hydrogeologic system. The simulation confirmed that steady-state flow conditions have been currently reached as indicated by consistency of computed heads. It also calibrated the values of the conductivity and recharge and ensured the sustainability of the El Obeid water supply project. A total of 3.5 × 10⁷ m³/year can be continually extracted from the deep aquifer to supply El Obeid city without endangering the groundwater resources in the region. The decline in water level will not exceed 25 m during the first 10 years, while indefinite continuous pumping will affect only the vicinity of the wells in a circle of 30 km diameter. Therefore, aquifer storage capacity and hydraulic properties encourage further groundwater exploitation. The present use of groundwater is extremely lower than the present demand, and it can potentially cover future demands without introducing significant changes to the system. The increase of pumping cost due to the decline in head subsequent to project operation was found to be minimal and of local effect.     

Mobility of rare earth elements in the system soils–plants–groundwaters: a case study of an arid area (Oman)

Groundwater samples from six wells and various species of plants from soils developed on ophiolites were collected from an arid area (AlKhod area, Oman) and analyzed for trace elements including rare earth elements (REEs). The distribution patterns of REEs in plants indicated an enrichment in middle REEs (MREEs?=?Sm to Dy) and heavy REEs (HREEs?=?Ho to Lu), when they are normalized to the REE composition of the Post Archean Australian Shale (PAAS), with a significant negative anomaly in Ce and a positive anomaly in Eu. Compared to Oman ophiolites, the REEs in different species of plants are depleted in Ce and enriched in MREEs and slightly enriched in light REE (LREE?=?from La to Nd). Relative to PAAS, the distribution of REEs in groundwaters revealed similar patterns to the REE distribution in plants. The distribution patterns of REEs in plants relative to those in waters are nearly flat. These patterns suggest that the transfer of REEs from soil solutions to the groundwaters in Oman occurs without any significant fractionation.     

Occurrence of Phthalates in Sewage Sludge from Three Wastewater Treatment Plants in Istanbul,Turkey

Phthalates are considered priority pollutants because of their potential adverse effects on ecosystems and human health. The objectives of this study were to determine the occurrence of five phthalates (DMP, DEP, DBP, BBP, and DEHP) in sewage sludge and to determine the seasonal variability of these contaminants at three (Bahçe?ehir, Pa?aköy, and Tuzla) full‐scale municipal and domestic wastewater treatment plants (WWTP) in Istanbul, Turkey. Mass balance was also calculated for DEHP at Tuzla WWTP sludge treatment units. DMP, DEP, DBP, BBP, and DEHP concentrations in sewage sludge ranged from 1.4 to 2.7 mg/kg dry weight (dw), 1.1 to 2.8, 0.6 to 4.6, 2.8 to 6.2, 18 to 490 mg/kg dw, respectively. Phthalate concentrations from the Bahçe?ehir and Pa?aköy WWTPs met the limit (100 mg/kg dw) of Turkey national sludge regulation and the Europe Union draft of sludge directive for land application, whereas phthalate concentrations from Tuzla WWTP exceeded the maximum permissible concentration. Phthalate concentrations did not show seasonal variations for Bahçe?ehir and Pa?aköy WWTPs, which receive mainly household wastewater while some fluctuations were observed DEP, DBP, and DEHP at Tuzla WWTP which has a lot of industrial wastewater contribution. The mass balance showed that approximately 17% of DEHP in the primary and secondary sludge was removed by anaerobic digestion, while 43% returned back to the beginning of the WWTP and 40% remained in the dewatered sludge. This study suggests that phthalates in sludge from WWTPs with industrial wastewater contribution may limit the use of sludge for land application.     

Early Triassic potassic volcanism in the Afyon Zone of the Anatolides/Turkey: implications for the rifting of the Neo-Tethys

Afyon Zone, which was derived from the Anatolide–Tauride platform during closure of the Neo-Tethys, is made up of pre-Mesozoic basement and unconformably overlying Triassic–Early Tertiary cover series. The Afyon Zone contains widespread metavolcanic rocks, which are dominated by rhyolite, dacite, and trachyandesite. They form a distinct volcanic succession, which is separated from the underlying Silurian–Lower Carboniferous metacarbonates and meta-siliciclastics by a regional unconformity. Trachyandesitic metavolcanics are made up of massive lava flows, pyroclastics and epiclastics, less frequently, domes and dikes, which were developed on a deeply eroded subaerial landmass. U/Pb and Pb/Pb zircon geochronology yielded Lower Triassic (~250 Ma) ages, which are interpreted as extrusion age of trachyandesitic volcanics. Based on the stratigraphic, geochronological, and geochemical data, we suggest that these Lower Triassic magmatic rocks represent an extensional tectonic setting on the northern active margin of the Gondwana, which led to the development of the northern branch of the Neo-Tethys.     

Optimal design of superelastic‐friction base isolators for seismic protection of highway bridges against near‐field earthquakes

The seismic response of a multi‐span continuous bridge isolated with novel superelastic‐friction base isolator (S‐FBI) is investigated under near‐field earthquakes. The isolation system consists of a flat steel‐Teflon sliding bearing and a superelastic NiTi shape memory alloy (SMA) device. The key design parameters of an S‐FBI system are the natural period of the isolated bridge, the yielding displacement of the SMA device, and the friction coefficient of the sliding bearings. The goal of this study is to obtain optimal values for each design parameter by performing sensitivity analysis of a bridge isolated by an S‐FBI system. First, a three‐span continuous bridge is modeled as two‐degrees‐of‐freedom with the S‐FBI system. A neuro‐fuzzy model is used to capture rate‐ and temperature‐dependent nonlinear behavior of the SMA device. Then, a set of nonlinear time history analyses of the isolated bridge is performed. The variation of the peak response quantities of interest is shown as a function of design parameters of the S‐FBI system and the optimal values for each parameter are evaluated. Next, in order to assess the effectiveness of the S‐FBI system, the response of the bridge isolated by the S‐FBI system is compared with the response of the non‐isolated bridge and the same bridge isolated by pure‐friction (P‐F) sliding isolation system. Finally, the influence of temperature variations on the performance of the S‐FBI system is evaluated. The results show that the optimum design of a bridge with the S‐FBI system can be achieved by a judicious specification of design parameters. Copyright © 2010 John Wiley & Sons, Ltd.