Introducing a new conceptual instantaneous unit hydrograph model based on a hydraulic approach

ABSTRACT

A novel approach is introduced for simulation of instantaneous unit hydrographs (IUHs). The model consists of a series of linear reservoirs that are connected to each other, and is referred to as the inter-connected linear reservoir model (ICLRM). By assuming the flow between two reservoirs is a linear function of the difference between the water levels in the reservoirs, a system of first-order linear differential equations is obtained as the ICLRM governing equation. By solving the equations, the discharge from the last reservoir is considered as an IUH. A small-scale laboratory device was constructed for the simulation of IUHs using the model. By studying four hydrographs extracted from the literature, and simulating them using both the ICLRM and the Nash model, it is concluded that the ICLRM can predict these hydrographs more accurately than the Nash model. Due to the simplicity of the construction and operation of the ICLRM and, more importantly, its visual aspect, the ICLRM may be considered as an effective educational tool for studying IUHs.     

Investigation of moment-rotation relation in different joint types and evaluation of their effects on segmental tunnel lining

This paper presents the results of a numerical study that has been performed to investigate the different joint types that affect the moment-rotation relation and ultimate bending moment capacity of a joint. A 3D finite element method was adapted to establish elaborate numerical models of segments. To evaluate the possible differences in moment-rotation behavior between different joint types, 10 different joint types were simulated. Additionally, the effect of different joint types on behavior of a lining ring was investigated. The validity of the peridynamic simulation was tested by comparing results obtained in this paper against the results obtained in a study performed by Hordijk and Gijsbers. Observations of the results demonstrate that in a flat joint, the expanding of joint height increased the rotation stiffness of the joint in the linear branch, and accordingly, the ultimate bending moment of the joint increased. In the ring model, it was observed that the expanding of joint height led to the decreased of ring displacement and stress concentration in the joint. Whenever there were full surface contacts (contact two segment in total cross section) in the joints, the rotation stiffness of the joints in the linear branch became equal, and, as a result, the displacement in the ring model was the same in all joint types. In addition, it was observed that using a convex joint in the ring model increases the displacement of the ring. The ultimate bending moment of bolted joints was higher than that of joints without bolts, especially in the case of a negative moment.     

Steady critical discharge rates from vertical and horizontal wells in fresh–saline aquifers with sharp interfaces

In this study, the critical (or maximum) discharge rates before saline water enters a well were determined for vertical and horizontal wells in a freshwater aquifer which is separated from a static saline aquifer by a sharp interface. Flow around the well was solved by integration of a point sink solution along the well axis, and both the critical discharge rate and critical interface rise were determined through a comparison of the heads and vertical gradients at the saline–fresh water interface. The rates were determined for vertical and horizontal wells with various lengths and depths for different aquifer salinities. Results were generalized by drawing dimensionless type curves. The results showed that the dimensionless total critical discharge rates are higher for the longer horizontal wells and longer vertical wells with a certain bottom depth, and they almost linearly decrease with well depth at rates of 0.7–0.9. For the dimensionless well length of 0.2, the dimensionless total discharge rate of a horizontal well is about 0.1 more than that of a vertical well with the same length and well-top depth. Also, the critical discharge rates per unit length of well are inversely proportional to well length and remarkably higher for shallower wells. Additionally, the critical pumping rate is proportional to the salinity difference of the aquifers. These results were confirmed by comparison to existing solutions for vertical wells with dimensionless lengths of 0.2, 0.5 and 0.6, and for critical interface rises in the range of 0.75–0.9.     

Vulnerability of Kuwait coast to sea level rise

Assessing coastal vulnerability to sea level rise (SLR) at local and regional scales is a fundamental step for designing successful long-term coastal management plans. This study was thus designed to assess Kuwait coastal vulnerability to SLR at four scenarios (.5, 1, 1.5 and 2 m). Potential inundated areas and the number of people at risk were estimated based on these SLR scenarios. A coastal vulnerability index (CVI) map of Kuwait was then computed based on the lowest scenario using eight parameters: elevation, coastal slope, geomorphology, distance to 20-m isobath, population, land use, cultural heritage and transportation. The geographic distribution of inundated areas at an SLR of .5 m revealed that the northern islands of Kuwait and coastal areas along Kuwait Bay would be highly impacted, whereas the coastal area near Shuaibah Port was the most influenced among the southern coasts. Most of the coastal area exhibited a moderate vulnerability to SLR, especially the northern islands. This study presented an initial vulnerability assessment for Kuwait coasts to SLR, which can be extended with more variables. The integrated remote sensing and geographic information system methodology demonstrated in this study can be applied in similar studies elsewhere.     

Analysis of soil nail walls performance - Case study

This study surveys the performance of temporary soil nail walls with a maximum height of 29.3 m in the Yas project, located in Tehran. Some numerical models, with various modelling approaches, were developed using finite element software and the proper modelling approaches were specified and verified.The modelling results were analysed and compared with the in situ monitored data. The results demonstrate the model’s horizontal deformations are generally greater than the in situ monitored values. To decrease the differences between models and monitored results, the effect of variations of the soil parameters had been surveyed and the limits of needed variations were specified.