The radio luminosity function and the luminosity diameter function of extragalactic radio sources

On the basis of a radio index-surface brightness diagram recently published, the luminosity function and the luminosity diameter function are obtained. The uncertainties due to the incompleteness of the sample are of the same order as the statistical uncertainties. The luminosity function differs considerably from a simple power law and supports the distinction of two populations. The density of the weak population (P<10³⁵ W Hz⁻¹ ster⁻¹ at 1400 MHz) follows nearly a power law in P and increases towards small diameters at least down to I kpc. The density of the strong population (the high luminosity and small diameter part of which is occupied by the quasars) has a maximum between 10²⁵ and 10²⁸ W Hz⁻¹ ster⁻¹ and around 100 kpc. A strong evolution effect is clearly present and is in a good agreement with the models obtained from the log N-log S counts.     

Extraction and recovery of precious metals from electronic waste printed circuit boards by bioleaching acidophilic fungi

Printed circuit boards contain precious metals. They are produced in large volumes, rendering them an important component of the electronic waste. In view of the heterogeneity of the metals present, reprocessing of electronic waste is a heinous task. The present study focused on leaching of valuable metals from electronic waste printed circuit boards using Aspergillus niger DDNS1. The adaptation phases began at 0.1, 0.5 and 1.0% of fine powder of printed circuit boards with 10% inoculum and were optimized with three effective factors, viz. initial pH, particle size and pulp density, to achieve the maximum simultaneous recovery of the valuable metals. The interactions of these metals were also deciphered using scanning electron microscopy, energy-dispersive X-ray spectroscopy, X-ray diffraction, Fourier transform infrared spectrum and atomic absorption spectroscopy. The results indicated that extraction of the precious metals was accomplished mainly through the unique organic acids originating from A. niger DDNS1. The initial pH played an important role in the extraction of the precious metals and the metals precipitate formation. The leaching rate of the metals was generally higher at low powder dosage of printed circuit boards. The toxicity of the printed circuit boards had little effect on two-step bioleaching at the pulp density of 0.1% compared to one-step bioleaching. The two-step bioleaching process was followed under organic acid-forming conditions for the maximum mobilization of metals. Thus, the precious metals from printed circuit boards could be mobilized through fungal bioleaching which promises an important industrial application in recycling of electronic wastes.     

Rare earth elements in the clay fraction of coaliferous sediments of the Arkagalinskoe (Magadan district) and Dolinskoe (Sakhalin Island) coalfields

The study of REE distribution in the clay fraction of sedimentary rocks from two coalfields made it possible to distinguish several types of REE distribution, which correlate with their mineral composition. It is shown that the REE fractionation was related to the mineral reconstruction of the primary clay fraction and some detrital minerals in the course of postsedimentary transformations of rocks during diagenesis, early catagenesis, and beginning of late catagenesis. These transformations were governed by several factors, such as the composition of sediments; hydrochemical features of accumulation environment; the chemical composition, dynamics, and feeding sources of pore solutions; the porosity and permeability of sediments and rocks; and the content of organic matter and its reaction ability.     

A 2D finite volume model for bebris flow and its application to events occurred in the Eastern Pyrenees

FLATModel is a 2D finite volume code that contains several original approaches to improve debris-flow simulation. Firstly, FLATModel incorporates a ＂stop-and-go＂ technique in each cell to allow continuous collapses and remobilizations of the debris-flow mass. Secondly, flow velocity and consequently yield stress is directly associated with the type of rheology to improve boundary accuracy. Thirdly, a simple approach for entrainment is also included in the model to analyse the effect of basal erosion of debris flows. FLATMODEL was tested at several events that occurred in the Eastern Pyrenees and simulation results indicated that the model can represent rather well the different characteristics observed in the field.     

Rock-weathering rates as functions of time

The scarcity of documented numerical relations between rock weathering and time has led to a common assumption that rates of weathering are linear. This assumption has been strengthened by studies that have calculated long-term average rates. However, little theoretical or empirical evidence exists to support linear rates for most chemical-weathering processes, with the exception of congruent dissolution processes. The few previous studies of rock-weathering rates that contain quantitative documentation of the relation between chemical weathering and time suggest that the rates of most weathering processes decrease with time. Recent studies of weathering rinds on basaltic and andesitic stones in glacial deposits in the western United States also clearly demonstrate that rock-weathering processes slow with time. Some weathering processes appear to conform to exponential functions of time, such as the square-root time function for hydration of volcanic glass, which conforms to the theoretical predictions of diffusion kinetics. However, weathering of mineralogically heterogeneous rocks involves complex physical and chemical processes that generally can be expressed only empirically, commonly by way of logarithmic time functions. Incongruent dissolution and other weathering processes produce residues, which are commonly used as measures of weathering. These residues appear to slow movement of water to unaltered material and impede chemical transport away from it. If weathering residues impede weathering processes then rates of weathering and rates of residue production are inversely proportional to some function of the residue thickness. This results in simple mathematical analogs for weathering that imply nonlinear time functions. The rate of weathering becomes constant only when an equilibrium thickness of the residue is reached. Because weathering residues are relatively stable chemically, and because physical removal of residues below the ground surface is slight, many weathering features require considerable time to reach constant rates of change. For weathering rinds on volcanic stones in the western United States, this time is at least 0.5 my.     

On the eigenvalues of kinematic α-effect dynamos

The kinematic α-effect dynamo problem is investigated in the case of an exterior perfect conductor. It is shown that certain approximate symmetries discovered in the numerical analysis of ROBERTS (1972) are exact for this case. As an illustration, an exact solution is given in a cylindrical geometry, where the equations can be written in terms of one variable. The implications for the earth's dynamo are discussed.     

A new semi-quantitative Surface-Enhanced Raman Spectroscopy (SERS) method for detection of maleimide (2,5-pyrroledione) with potential application to astrobiology

Nitrogen-containing heterocyclic compounds are fundamental biochemical components of all life on Earth and, presumably, life elsewhere in our solar system. Dete...     

Geotechnical assessment of the bearing capacity of coal mine floors

Summary This investigation concerns 3 longwall faces having variable strata and mining conditions, but supported by 202 tonnes hydraulic 6-leg chocks. Bearing capacity tests along the faces were conducted to evaluate the factors influencing floor deformation and failure. The effect of size, shape and perimeter of the base plates, thickness of the floor layer, time and moisture on the ultimate bearing capacity of the floor was measured and discussed. Application of this work is the prediction of stability and support performance of face ends, as well as the design of support systems and ground control on production faces.