西北太平洋柔鱼冬春生群体栖息地的变化研究

柔鱼（Ommastrephes bartramii）是短生命周期鱼种,其适宜栖息地范围受海洋水温条件的显著影响。本文根据2006-2015年7-11月中国鱿钓技术组提供的西北太平洋柔鱼冬生群体的捕捞数据以及海表温度（SST）数据,利用捕捞努力量与SST的频率分布关系,估算柔鱼各月适宜温度范围（PFSST）,对1985-2015年柔鱼PFSST进行估算,同时分析柔鱼PFSST的年代际变化规律,并评估不同强度厄尔尼诺和拉尼娜事件对柔鱼栖息地的影响。研究表明,2006-2015年柔鱼各月适宜的SST具有明显变化,7-11月对应适宜的SST范围分别为16~19℃、17~21℃、15~19℃、14~16℃和12~13℃。单位捕捞努力量渔获量大小随PFSST变动而发生相应变化,两者具有显著正相关关系,这说明了柔鱼渔场范围内适宜温度面积增加,对应柔鱼资源丰度上升。1985-2015年柔鱼PFSST呈现显著的月间和年际变化,7-11月PFSST具有先增加后递减的变化规律,且7-9月PFSST年际波动相似,10和11月PFSST年际变化相似。同时,柔鱼PFSST与渔场内SST具有显著正相关关系。柔鱼渔场内PFSST受厄尔尼诺和拉尼娜事件调控,其面积随气候事件的强度发生变化,具体表现为:弱拉尼娜事件和正常气候条件下,柔鱼渔场范围内水温最高,适宜栖息面积显著增长;中等强度和高强度拉尼娜条件下,柔鱼渔场内平均水温较高,但适宜栖息面积较前两者显著减小;弱强度、中等强度和超高强度厄尔尼诺条件下,柔鱼渔场内水温均较低,但弱强度和超高强度厄尔尼诺条件下柔鱼适宜栖息面积均大于中等强度厄尔尼诺条件。     

基于熵权TOPSIS模型的海岛地区资源环境承载力研究——以舟山普陀区、定海区为例

随着海洋强国、"一带一路"、生态文明建设等国家战略的不断推进,海岛在国家政治、军事、经济、社会、生态中的地位不断提高,海岛开发、利用的规模越来越大,其生态保护也面临着新的挑战。本文依据资源环境承载力内涵,兼顾海岛资源环境特点,研究形成海岛地区资源环境承载力评价指标体系,综合应用熵权法、TOPSIS(逼近理想解排序方法)模型评价了典型海岛地区——普陀区与定海区2009-2015年间的资源环境承载力状况,结果表明:普陀和定海资源环境承载力水平呈稳步提升趋势,各个时期的环境保护政策和节能减排相关措施在环境保护与污染治理等方面起到了较为积极的作用。最后,在基于生态系统的海岛综合管理框架内提出了对策建议。     

潮流界以下河段航道整治水位确定方法研究——以长江江阴以下河段为例

在总结分析现有整治水位确定方法的基础上,根据潮流界以下河段的水沙运动特性,本文提出一种基于输沙能力的航道整治水位确定方法。考虑上游来水、下游潮汐为独立事件,统计潮流界以下河段上游来水、下游潮汐不同等级组合出现的频率,采用数学模型计算相应组合下河段沿程的潮位、流速过程,以流速四次方代表水流的输沙能力,统计不同潮位等级对应的综合净输沙能力,确定最大综合净输沙能力对应的水位为(最优)航道整治水位。以长江下游白茆沙水道和福姜沙水道为例,计算了所在河段的航道整治水位,并探讨了起动流速对整治水位计算的影响和最高整治水位概念对工程的意义。     

基于UDF的水平轴潮流能水轮机被动旋转水动力性能研究

针对水平轴潮流能水轮机被动旋转问题,基于Fluent 17.0,运用UDF(User Defined Function)控制滑移网格对网格进行动态调整,仿真研究水轮机在不同安放角下被动旋转的水动力特性。通过仿真分析,结果表明:潮流能水轮机随着叶片安放角度的增加,尖速比、输出功率、捕能系数都是先增大后减小,叶片安放角为6°时,叶轮前后速度差最大,对潮流能利用充分,且各项性能均达到最佳;通过分析叶片受力,叶尖叶素在安放角为2°时阻力最大,3°时升力最大,升阻比在6°时最大,此时叶尖叶素升阻比C_L/C_D=6.27、攻角α=3.06°。由仿真结果可知水平轴潮流能叶轮的自启动过程由5个阶段组成,即加速度增大的加速运动段—加速度减小的加速运动段—加速度反向增大的减速运动段—加速度反向减小的减速运动段—稳定运行段,这对潮流能水轮机的设计具有重要的指导意义。     

深水海底管道铺设安全辅助系统

此次研发的铺管安全辅助系统是一套自动化、简易化、旨在提高安装经济性和安全性的实时运行安全辅助系统,通过实时数据采集及处理,达到对安装期海管强度进行实时监测目的。系统组成包括设备系统和监测软件两部分。设备为系统提供辅助决策数据源;监测软件采用C++语言编写,用于数据接收、解析,并通过OrcaFlex API调用商业有限元软件OrcaFlex为分析内核进行实时分析计算,以可视化界面输出管道应力、应变、触地点等信息,给予船上作业人员安全指导,及时作出决策。     

Establishment and application of an intelligent treating method for oil spill identification

In the identifying process of an oil spill accident, manual integral and artificial visual comparison are commonly used at present to determine the oil spill sources, these methods are time-consuming and easily affected by human factors. Therefore, it is difficult to achieve the purpose of rapid identification of an oil spill accident. In this paper, an intelligent method of automatic recognition, integration and calculation of diagnostic ratio of Gas Chromatography-Mass Spectrometer (GC/MS) spectrum are established. Firstly, four hundreds of samples collected around the world were analyzed using a standard method and Retention time locking technology (RTL) was applied to reduce the change of retention time of GC/MS spectrum. Secondly, the automatic identification, integration of n-alkanes, biomarker compounds, polycyclic aromatic hydrocarbons and calculation of the diagnostic ratios were realized by MATLAB software. Finally, a database of oil fingerprints were established and applied successfully in a spill oil accident. Based on the new method and database, we could acquire the diagnostic ratios of an oil sample and find out the suspected oil within a few minutes. This method and database can improve the efficiency in spilled oil identification.     

系缆损伤对绷紧式系泊系统动力响应的影响

探究合成纤维系缆损伤对绷紧式系泊系统响应的影响,具有重要的工程意义。通过高强聚乙烯(HMPE)缆绳损伤动刚度实验,获得其动刚度随损伤的演变规律。在数值计算上,借鉴并合理简化了前人提出的动刚度经验公式,通过处理实验结果确定动刚度经验公式的参数并进行验证。在此基础上,以一座采用高强聚乙烯缆绳为主体系缆的FPSO为例,将所得动刚度经验公式导入系泊分析软件,结合水动力分析,计算得到在相同海洋环境中,系缆发生不同程度损伤时,各系缆张力和平台偏移响应的结果。通过处理、分析所得的计算结果,获得合成纤维缆绳损伤演变对绷紧式系泊系统响应的影响规律,并据此为系缆更换提供了建议。这些成果既有利于把握绷紧式系泊系统的非线性动力响应,也对安全、经济、合理地运用合成纤维系缆具有重要意义。     

10MW级海上浮式风机运动特性研究

以DTU 10 MW基准风机为研究对象,单柱式平台作为基础支撑结构,使用FAST软件计算分析,考虑单独风、单独波浪以及风浪组合三种环境条件,对10 MW级海上浮式风机的运动特性进行研究。研究发现:系统摇荡是风激励的低频运动和波浪激励的波频运动的合成,气动阻尼削弱系统的波频运动;系统纵荡和纵摇运动存在明显的耦合现象,而垂荡运动和其他方向的运动没有耦合关系;受纵摇影响,转动的风轮产生陀螺惯性力矩,激励首摇运动;随着风机单机容量的增加,风激励的低频运动比例增大,波浪激励的波频运动比例减小。     

Experimental Study on Cross-Flow Induced Vibrations in Heat Exchanger Tube Bundle

Vibration in heat exchangers is one of the main problems that the industry has faced over last few decades. Vibration phenomenon in heat exchangers is of major concern for designers and process engineers since it can lead to the tube damage, tube leakage, baffle damage, tube collision damage, fatigue, creep etc. In the present study, vibration response is analyzed on single tube located in the centre of the tube bundle having parallel triangular arrangement (60°) with P/D ratio of 1.44. The experiment is performed for two different flow conditions. This kind of experiment has not been reported in the literature. Under the first condition, the tube vibration response is analyzed when there is no internal flow in the tube and under the second condition, the response is analyzed when the internal tube flow is maintained at a constant value of 0.1 m/s. The free stream shell side velocity ranges from 0.8 m/s to 1.3 m/s, the reduced gap velocity varies from 1.80 to 2.66 and the Reynolds number varies from 44500 to 66000. It is observed that the internal tube flow results in larger vibration amplitudes for the tube than that without internal tube flow. It is also established that over the current range of shell side flow velocity, the turbulence is the dominant excitation mechanism for producing vibration in the tube since the amplitude varies directly with the increase in the shell side velocity. Damping has no significant effect on the vibration behavior of the tube for the current velocity range.     

Investigation on the Effect of Geometrical and Geotechnical Parameters on Elongated Offshore Piles Using Fuzzy Inference Systems

Among numerous offshore structures used in oil extraction, jacket platforms are still the most favorable ones in shallow waters. In such structures, log piles are used to pin the substructure of the platform to the seabed. The pile’s geometrical and geotechnical properties are considered as the main parameters in designing these structures. In this study, ANSYS was used as the FE modeling software to study the geometrical and geotechnical properties of the offshore piles and their effects on supporting jacket platforms. For this purpose, the FE analysis has been done to provide the preliminary data for the fuzzy-logic post-process. The resulting data were implemented to create Fuzzy Inference System (FIS) classifications. The resultant data of the sensitivity analysis suggested that the orientation degree is the main factor in the pile’s geometrical behavior because piles which had the optimal operational degree of about 5° are more sustained. Finally, the results showed that the related fuzzified data supported the FE model and provided an insight for extended offshore pile designs.