Iron isotopic analyses of geological reference materials on MC-ICP-MS with instrumental mass bias corrected by three independent methods

Here we report iron (Fe) isotopic data of three pure Fe solution standards (IRMM-014, GSB Fe, and NIST 3126a) and five widely used geological reference materials (RMs) from the United States Geological Survey and Geological Survey of Japan obtained on a Neptune Plus multi-collector–inductively coupled plasma–mass spectrometer (MC-ICP-MS) in our laboratory over the past 3 years. The instrumental mass bias was corrected by three independent methods: sample-standard bracketing (SSB), Ni doping?+?SSB, and ⁵⁷Fe–⁵⁸Fe double spike?+?SSB. Measurements reveal that both the Ni doping and double spike methods helped calibrate short-term fluctuations in mass bias. Collectively, almost all measurements of RMs yielded δ⁵⁶Fe within?±?0.05 of recommended values, provided that each sample was measured four times on MC-ICP-MS. For the first time, new recommended values for NIST SRM3126a are reported (δ⁵⁶Fe?=?0.363?±?0.006, 2SE, 95% CI; and δ⁵⁷Fe?=?0.534?±?0.010, 2SE).     

The effect of annealing on the luminescence decay-time of synthetic calcite:Mn

Calcite was synthesized by four methods, and the luminescence decay-time was measured for nine samples before and after heating hydrothermally in the temperature range 200–400°C. Decay-time data were collected between room temperature and approximately 15 K. The decay time at room temperature is approximately 50 ms, with little difference between a given calcite before and after hydrothermal treatment. The decay time at 15 K is always greater than at room temperature as the effect of thermal quenching diminishes. Differences in decay time before and after heating are more apparent at low temperature owing to this reduction in thermal quenching. The decay time decreased significantly in two samples, and an increase in decay time was observed in the remaining seven samples following heating. Among the latter group, the change in decay time was insignificant in three samples. The results are compared with previous data in which it was shown that the effect of heating is to increase the intensity of luminescence.     

An Overview of Dissolved and Suspended Matter Fluxes in the Loire River Basin: Natural and Anthropogenic Inputs

The spatial and temporal distributions of major elements were investigated in the surface waters and in associated suspended matter at two sites of the upper Loire basin (Orleans and Brehemont) between 1995 and 1998.According to geochemical and isotopic patterns, the dissolved load appears to result from a process of mixing rainwater inputs, weathering processes of carbonate and silicate bedrock, and agricultural and urban inputs. Natural inputs influence 60% of water chemical composition at both sites. Annual dissolved fluxes were estimated to be 1300 10³ t/y at Orleans and 1620 10³ t/y at Brehemont. Major elements are transported mainly in the dissolved fraction. After correcting for atmospheric and anthropogenic inputs, the silicate specific export rate was calculated to be 11 t/y/km² throughout the basin and the carbonate specific export rate to be from 47 t/y/km² at Orleans to 23 t/y/km² at Brehemont.The suspended load appears to result from at least two particle reservoirs: a silicate reservoir and a carbonate reservoir. The silicate reservoir has a detrital origin, mainly during periods of high flow, while the carbonate reservoir has a detrital origin during periods of high flow and an authigenic origin during periods of low flow. Of the total annual flow of suspended matter, this authigenic material represents 16% at Orleans, 25% at Brehemont and 37% in the fluvial part of the estuary. After correcting authigenic inputs, the specific export rate due to mechanical weathering was estimated to be 8 t/y/km² throughout the Loire basin.     

Citizens as sensors: the world of volunteered geography

In recent months there has been an explosion of interest in using the Web to create, assemble, and disseminate geographic information provided voluntarily by individuals. Sites such as Wikimapia and OpenStreetMap are empowering citizens to create a global patchwork of geographic information, while Google Earth and other virtual globes are encouraging volunteers to develop interesting applications using their own data. I review this phenomenon, and examine associated issues: what drives people to do this, how accurate are the results, will they threaten individual privacy, and how can they augment more conventional sources? I compare this new phenomenon to more traditional citizen science and the role of the amateur in geographic observation.     

Assessing the vulnerability of social–environmental system from the perspective of hazard,sensitivity, and resilience: a case study of Beijing,China

Despite a recent increase in the number of vulnerability analyses there has been relatively little discussion of vulnerability assessment of social–environment system, especially when they face multiple hazards. In this study, we developed an applicable and convenient method to assess vulnerability of social–environment system at a regional scale. Vulnerability is quantified by measuring three critical elements (i.e. hazards, sensitivity, and resilience) through some key variables. The results showed that vulnerability is high in Miaofeng Mountain in Mengtougou District, the hills of Pinggu County and the riparian zones of the lower courses of the Beiyun and Yongding Rivers; but low in the city of Beijing and the southwestern part of the Fangshan District. Areas of very high, high, medium, and low-vulnerability account for 6.19, 25.48, 33.06, and 35.27% of the total area, respectively. The degree of vulnerability decreases in a northwest direction in mountainous areas and declines from watercourses to riparian zones along a lateral direction in the plain. Some adaptive strategies are also proposed.     

Structural improvement of age-hardened gypsum-treated bauxite red mud waste using readily decomposable phyto-organics

Several years (7) after incidental lithification by added gypsum, the effect of crushing and phyto-organics on some physical properties of red mud wastes (RMW) was examined under laboratory conditions. It was hypothesized that mechanically breaking up the hardened masses would increase their permeability. However, on the contrary, crushing these rock-hard masses into <2-mm particles did not increase permeability. A phyto-organic treatment on the other hand greatly improved permeability of the crushed entities such that infiltration rates increased from 0 to 10 cm/h. After 24 weeks of incubation, the structure of the newly formed phyto-organically treated gypsum-hardened RMW aggregates was also substantially improved over that of the controls, as a >3-fold increase in resistance to disintegration during wet sieving was exhibited by the phyto-organically treated samples. The increase in water infiltration by combining crushing with phyto-organic applications was ascribed to a decrease in particle dispersion, creating more stable clay clusters, which in turn stabilized channels and pores. Conversely, it was concluded that the singular crushing of gypsum-hardened bauxite waste in the waste dumps is potentially wasteful and ineffective.     

Bristen granite: a highly differentiated,fluorite-bearing A-type granite from the Aar massif,Central Alps,Switzerland

Bristen granite is a body of fine-grained leucogranite occurring in the Gotthard rail base tunnel in the Central Alps. During construction of the tunnel, Bristen granite (Brgr) has been drilled along a 600 m long section. The aplite-granite belongs to the suite of Variscan granitoid intrusions of the Aar massif and contains a variety of accessory minerals typical of highly differentiated granites. Rock forming fluorite, partly enriched in yttrium (Y) and rare earth elements (REE), is intergrown with the late Y- and REE-bearing carbonate mineral synchysite. The granite contains a variety of Ti- and Y-REE-niobates, thorite, and zircon. Compared with the calc-alkaline central Aar granite (cAgr), Bristen granite is strongly depleted in Ti, P, Mg, Sr, and Ba and shows a remarkable enrichment in incompatible elements such as Rb, Th, U, Nb, Y, HREE and F. Bristen granite is the most evolved granitoid rock of the Aar massif. The composition of Brgr is typical of post-collisional reduced (ferroan) A-type granites. The Brgr melt formed in the lower crust and crystallized from a highly differentiated melt at the cotectic point in the quartz-feldspar system close to 100 MPa and 700 °C. The Brgr intruded as a small isolated stock pre-Variscan gneisses with sharply discordant contacts. The primary igneous host of Nb, Ta, Y, U, Th and REE is biotite in addition to minor amounts of allanite, and zircon. The presence of Y-REE-fluorite, synchysite, parisite and Y- and Ti-niobates and other REE-minerals can be related to reaction of igneous biotite and primary fluorite with hydrothermal fluids. The reaction is associated with alpine metamorphism, because Y-bearing fluorite and synchysite have been reported from Alpine fissures. The transformation of primary biotite to chlorite and muscovite released the heavy metal oxides under lower greenschist facies conditions that formed the Alpine diagnostic mineral stilpnomelane at about 300 °C.     

Chemical composition of rock-forming minerals and crystallization physicochemical conditions of the Middle Eocene I-type Haji Abad pluton,SW Buin-Zahra,Iran

The Haji Abad intrusion is a well-exposed Middle Eocene I-type granodioritc pluton in the Urumieh–Dokhtar magmatic assemblage (UDMA). The major constituents of the investigated rocks are K-feldspar, quartz, plagioclase, pyroxene, and minor Fe–Ti oxide and hornblende. The plagioclase compositions fall in the labradorite, andesine, and oligoclase fields. The amphiboles range in composition from magnesio-hornblende to tremolite–hornblende of the calcic-amphibole group. Most pyroxenes principally plot in the field of diopside. The calculated average pressure of emplacement is 1.9 kbar for the granodioritic rocks, crystallizing at depths of about 6.7 km. The highest pressure estimated from clinopyroxene geobarometry (5 kbar) reflects initial pyroxene crystallization pressure, indicating initial crystallization depth (17.5 km) in the Haji Abad granodiorite. The estimated temperatures using two-feldspar thermometry give an average 724 °C. The calculated average temperature for clinopyroxene crystallization is 1090 °C. The pyroxene temperatures are higher than the estimated temperature by feldspar thermometry, indicating that the pyroxene and feldspar temperatures represent the first and late stages of magmatic crystallization of Haji Abad granodiorite, respectively. Most pyroxenes plot above the line of Fe³⁺?=?0, indicating they crystallized under relatively high oxygen fugacity or oxidized conditions. Furthermore, the results show that the Middle Eocene granitoids crystallized from magmas with H₂O content about 3.2 wt%. The relatively high water content is consistent with the generation environment of HAG rocks in an active continental margin and has allowed the magma to reach shallower crustal levels. The MMEs with ellipsoidal and spherical shapes show igneous microgranular textures and chilled margins, probably indicating the presence of magma mixing. Besides, core to rim compositional oscillations (An and FeO) for the plagioclase crystals serve as robust evidence to support magma mixing. The studied amphiboles and pyroxenes are grouped in the subalkaline fields that are consistent with crystallization from I-type calc-alkaine magma in the subduction environment related to active continental margin. Mineral chemistry data indicate that Haji Abad granodiorites were generated in an orogenic belt related to the volcanic arc setting consistent with the subduction of Neo-Tethyan oceanic crust beneath the central Iranian microcontinent.     

Fragmentation during Rock Falls: Two Italian Case Studies of Hard and Soft Rocks

In recent years, rock fall phenomena in Italy have received considerable attention for risk mitigation through in situ observations and experimental data. This paper reports the study conducted at Camaldoli Hill, in the urban area of Naples, and at Monte Pellegrino, Palermo, Italy. The rocks involved are volcanic Neapolitan yellow tuff (NYT) in the former area and dolomitic limestone in the latter. Both rocks, even though with different strength characteristics, have shown a significant tendency towards rock fragmentation during run out. This behavior was first investigated by comparing the volumes of removable blocks on the cliff faces (V ₀) and fallen blocks on the slopes (V _f). It was assumed that the ratio V _f/V ₀ decreases with the distance (x _f) from the detachment area by an empirical law, which depends on a coefficient α, correlated with the geotechnical properties of the materials involved in the rock fall. Finally, this law was validated by observation of well-documented natural rock falls (Palermo) and by in situ full-scale tests (Naples). From the engineering perspective, consideration of fragmentation processes in rock fall modeling provides a means for designing low-cost mitigation measures.     

Raman spectroscopic study of K-lingunite at various pressures and temperatures

K-lingunite is a high-pressure modification of K-feldspar that possesses the tetragonal hollandite structure. Variations of the Raman spectra of K-lingunite were studied up to ~31.5 GPa at room temperature, and in the range 79–823 K at atmospheric pressure. The Raman frequencies of all bands were observed to increase with increasing pressure, and decrease with increasing temperature for K-lingunite. This behavior is in line with those observed for most of other materials. New sharp Raman bands appear at pressures greater than 13–15 GPa, suggesting a phase transition in K-lingunite with increasing pressure. The transition is reversible when pressure was released. The appearance of these new Raman bands may correspond to the phase transition revealed earlier at around 20 GPa by X-ray diffraction studies. Instead of transforming back to its stable minerals, such as orthoclase, microcline or sanidine, K-lingunite became amorphous in the temperature range 803–823 K at atmospheric pressure.