Thermal stability of a layer with permeable boundaries and variable gravitational field

The aim of this paper is to investigate the thermal stability of a fluid layer with permeable boundaries and a variable gravitational field. It is observed that the principle of exchange of stabilities is valid when the layer is heated form below and the complex growth rate of an arbitrary oscillatory mode exists outside of a circle whose radius depends upon the permeability parameter, Prandtl number and wavelength of the mode. In the case of a layer heated from below, gravity increasing upward has a destabilizing effect whereas the permeability parameter has a stabilizing effect.     

Radiative and free-convection effects on the oscillatory flow past a vertical plate

The interaction of free convection with thermal radiation of the oscillatory flow past a vertical plate is studied. The Rosseland approximation is used to describe the radiative heat flux in the energy equation.     

Physical parameters of near-Earth asteroid 1982 DV

Visual and infrared observations were made of Amor asteroid 1982 DV during its discovery apparition. Broadband visual and near-infrared photometry shows that it is an S-class asteroid. Narrowband spectrophotometry shows an absorption feature due to olivine or pyroxene or both centered at 0.93 μm. Applying a nonrotating thermal model to 10-μm photometry, the geometric albedo is calculated to be approximately 0.27. The geometric albedo for a slowly rotating, rocky surface was calculated for 1 night to be 0.15, consistent with S-class asteroid albedos. Thus, 1982 DV is either one of the most reflective S-class asteroids known, or a significant amount of bare rock is exposed on the asteroid's surface. For the nonrotating model, ellipsoidal dimensions for 1982 DV are 3.5 × 1.4 × 1.4 km.     

OTEC cold-water pipe research

Shelf-mounted Ocean Thermal Energy Conversion (OTEC) plants require installation of cold-water pipes (CWP) on slopes of40degto depths of 1000 m. In addition, tower platforms containing OTEC power systems may be located on lesser sloped terrain near shore and exposed to special environmental loading problems affecting foundation design. Shelf-mounted installations require careful attention to site selection and geotechnical considerations for foundation integrity on sloped surfaces. This paper primarily discusses research associated with cold-water pipe and foundation installations on steep slopes, although research continues on tower platforms located on the shelf. At least five nations are in various stages of development of OTEC systems for island applications. Each of their systems is either shelf mounted or land based and requires that a large diameter cold-water pipe be installed on a steep slope to provide cold water from 1000-m depths. In addition to the installation and deployment of the large cold-water pipe, the most significant problem is the design and installation of suitable foundations that will last for several decades. To date there is very little experience in the offshore industry for large installations on steep slopes. A major scale-model research project is underway on the slopes of the island of Hawaii. A section of pipe 2.4 m in diameter and 24 m long was installed using combination concrete foundations and joints. The pipe and foundations are fully instrumented to measure environmental loading forces due principally to currents and waves. Environmental measurements will also be taken in the test area. The measurement data will be used to validate available analytical models for subsequent use in aiding industry in providing more cost-effective designs for OTEC pipes and foundations.     

Three dimensional simulation of fluid flow in X‐ray CT images of porous media

A numerical scheme is developed in order to simulate fluid flow in three dimensional (3‐D) microstructures. The governing equations for steady incompressible flow are solved using the semi‐implicit method for pressure‐linked equations (SIMPLE) finite difference scheme within a non‐staggered grid system that represents the 3‐D microstructure. This system allows solving the governing equations using only one computational cell. The numerical scheme is verified through simulating fluid flow in idealized 3‐D microstructures with known closed form solutions for permeability. The numerical factors affecting the solution in terms of convergence and accuracy are also discussed. These factors include the resolution of the analysed microstructure and the truncation criterion. Fluid flow in 2‐D X‐ray computed tomography (CT) images of real porous media microstructure is also simulated using this numerical model. These real microstructures include field cores of asphalt mixes, laboratory linear kneading compactor (LKC) specimens, and laboratory Superpave gyratory compactor (SGC) specimens. The numerical results for the permeability of the real microstructures are compared with the results from closed form solutions. Copyright © 2004 John Wiley & Sons, Ltd.     

A comparison of theoretical Sv emission line strengths with extreme ultraviolet observations of a sunspot

Electron impact excitation rates for transitions in the S v ion, calculated with theR-matrix code, are used to derive the electron temperature sensitive emission line ratiosR ₁ =I(854.8 Å)/I(786.9 Å),R ₂ =I(852.2 Å)/I(786.9 Å),R ₃ =I(849.2 Å)/I(786.9 Å), andR ₄ =I(1199.1 Å)/I(786.9 Å), which are found to be significantly different from previous estimates. A comparison of the present results with observational data for a sunspot obtained with the Harvard S-055 spectrometer on boardSkylab reveals generally good agreement between theory and experiment, except in the case ofR ₁, which is probably due to blending in the 854.8 Å feature. The possible effects of Lyman continuum absorption on the observed line ratios is briefly discussed.