Performance of activated carbon-impregnated cellulose filters for indoor VOCs and dust control

An activated carbon-impregnated cellulose filter was fabricated, and the capacity to remove dust and volatile organic compounds was evaluated in a laboratory. The adsorption capacities for benzene, toluene, ethyl benzene and m-xylene gases were compared by an adsorption isotherm test conducted as a preliminary test, showing that m-xylene and benzene were the most and least favorable for adsorption onto activated carbon, respectively. Cellulose filters were made with four levels of activated carbon contents, and dust removal was performed with all of the filters showing 99 % and higher efficiencies stable with a small variation during the experiment. Activated carbon content of 5 g in the unit filter area (125 g/m²) was found optimum for benzene, toluene, ethylbenzene and m-xylene removal, as it appeared that higher than 5 g activated carbon content was unnecessary for the improvement of its capacity. With increasing benzene, toluene, ethylbenzene and m-xylene loading, the highest removal rates were determined as 0.33–0.37 mg/cm² s for as short as 0.0046 s of air filter residence time. The rapid removal was possible because of the high surface area of the activated carbon-impregnated cellulose filter provided by powdered activated carbon, which is distinguished from the granular form in conventional activated carbon towers. As fixed within a cellulose scaffolding structure, the powdered activated carbon performed excellent benzene, toluene, ethylbenzene, and m-xylene adsorption (98.9–100 %), and at the same time, particular matters were removed in average 99.7 % efficiency after being filtered through the cellulose filter sheet.     

Discovery of Pyrrhotite-Chalcopyrite-Bearing Amphibole Megacrysts in Tongling Area, Anhui Province

Some pyrrhotite-chalcopyrite-bearing amphibole megacrysts (including pyroxene megacrysts) were discovered in Mesozoic augite diorite-porphyrite at Caoshan in Tongling area, Anhui Province. The amphibole megacrysts, belonging mainly to pargasite and magnesiohastingsite, are characteristic of the amphibole composition derived from mantle and crystallized in lower crust. In general, the aggregates of pyrrhotite-chalcopyrite take the shapes of cylinder and sphere. Three occurrences have been recognized in the amphibole megacrysts: parallel linear, bunchy and scattered. The unique cylinder-like shape of the aggregates and remarkable Ni-poor sulfides in Caoshan are distinctively different from the spherical Ni-rich sulfides in pyroxene megacrysts and any other kinds of megacrysts. In terms of composition, the amphibole megacrysts and their sulfides in Caoshan are similar to those in the pyroxenite xenoliths in Qilin, Guangdong Province. In terms of origin, the pyrrhotite-chalcopyrites as exsolution products resulted from the subsolidus re-equilibration of sulfide solid solution within amphibole megacrysts.amphibole megacrysts were first discovered inside and outside China. This discovery is important for the study of regional magma evolution and its associated mineralizations and ore sources as well.     

Pre- and syn-eruptive degassing and crystallisation processes of the 2010 and 2006 eruptions of Merapi volcano,Indonesia

The 2010 eruption of Merapi (VEI 4) was the volcano’s largest since 1872. In contrast to the prolonged and effusive dome-forming eruptions typical of Merapi’s recent activity, the 2010 eruption began explosively, before a new dome was rapidly emplaced. This new dome was subsequently destroyed by explosions, generating pyroclastic density currents (PDCs), predominantly consisting of dark coloured, dense blocks of basaltic andesite dome lava. A shift towards open-vent conditions in the later stages of the eruption culminated in multiple explosions and the generation of PDCs with conspicuous grey scoria and white pumice clasts resulting from sub-plinian convective column collapse. This paper presents geochemical data for melt inclusions and their clinopyroxene hosts extracted from dense dome lava, grey scoria and white pumice generated during the peak of the 2010 eruption. These are compared with clinopyroxene-hosted melt inclusions from scoriaceous dome fragments from the prolonged dome-forming 2006 eruption, to elucidate any relationship between pre-eruptive degassing and crystallisation processes and eruptive style. Secondary ion mass spectrometry analysis of volatiles (H₂O, CO₂) and light lithophile elements (Li, B, Be) is augmented by electron microprobe analysis of major elements and volatiles (Cl, S, F) in melt inclusions and groundmass glass. Geobarometric analysis shows that the clinopyroxene phenocrysts crystallised at depths of up to 20 km, with the greatest calculated depths associated with phenocrysts from the white pumice. Based on their volatile contents, melt inclusions have re-equilibrated during shallower storage and/or ascent, at depths of ~0.6–9.7 km, where the Merapi magma system is interpreted to be highly interconnected and not formed of discrete magma reservoirs. Melt inclusions enriched in Li show uniform “buffered” Cl concentrations, indicating the presence of an exsolved brine phase. Boron-enriched inclusions also support the presence of a brine phase, which helped to stabilise B in the melt. Calculations based on S concentrations in melt inclusions and groundmass glass require a degassing melt volume of 0.36 km³ in order to produce the mass of SO₂ emitted during the 2010 eruption. This volume is approximately an order of magnitude higher than the erupted magma (DRE) volume. The transition between the contrasting eruptive styles in 2010 and 2006 is linked to changes in magmatic flux and changes in degassing style, with the explosive activity in 2010 driven by an influx of deep magma, which overwhelmed the shallower magma system and ascended rapidly, accompanied by closed-system degassing.     

Analysis of solar radiation on the surface estimated from GWNU solar radiation model with temporal resolution of satellite cloud fraction

Preliminary analysis with a solar radiation model is generally performed for photovoltaic power generation projects. Therefore, model accuracy is extremely important. The temporal and spatial resolutions used in previous studies of the Korean Peninsula were 1 km × 1 km and 1-h, respectively. However, calculating surface solar radiation at 1-h intervals does not ensure the accuracy of the geographical effects, and this parameter changes owing to atmospheric elements (clouds, aerosol, ozone, etc.). Thus, a change in temporal resolution is required. In this study, one-year (2013) analysis was conducted using Chollian geostationary meteorological satellite data from observations recorded at 15-min intervals. Observation data from the intensive solar site at Gangneung-Wonju National University (GWNU) showed that the coefficient of determination (R²), which was estimated for each month and season, increased, whereas the standard error (SE) decreased when estimated in 15-min intervals over those obtained in 1-h intervals in 2013. When compared with observational data from 22 solar sites of the Korean Meteorological Administration (KMA), R² was 0.9 or higher on average, and over- or under-simulated sites did not exceed 3 sites. The model and 22 solar sites showed similar values of annual accumulated solar irradiation, and their annual mean was similar at 4,998 MJ m^?2 (3.87 kWh m^?2). These results show a difference of approximately ± 70 MJ m^?2 (± 0.05 kWh m^?2) from the distribution of the Korean Peninsula estimated in 1-h intervals and a higher correlation at higher temporal resolution.     

Estimation of Block Sizes for Rock Masses with Non-persistent Joints

Summary  Discontinuities or joints in the rock mass have various shapes and sizes. Along with the joint orientation and spacing, the joint persistence, or the relative size of the joint, is one of the most important factors in determining the block sizes of jointed rock masses. Although the importance of joint persistence on the overall rock mass strength has long been identified, the impact of persistence on rock strength is in most current rock mass classification systems underrepresented. If joints are assumed to be persistent, as is the case in most designs, the sizes of the rock blocks tend to be underestimated. This can lead to more removable blocks than actually exist in-situ. In addition, a poor understanding of the rock bridge strength may lead to lower rock mass strengths, and consequently, to excessive expenditure on rock support. In this study, we suggest and verify a method for the determination of the block sizes considering joint persistence. The idea emerges from a quantitative approach to apply the GSI system for rock mass classification, in which the accurate block size is required. There is a need to statistically analyze how the distribution of rock bridges according to the combination of joint orientation, spacing, and persistence will affect the actual size of each individual block. For this purpose, we generate various combinations of joints with different geometric conditions by the orthogonal arrays using the distinct element analysis tools of UDEC and 3DEC. Equivalent block sizes (areas in 2D and volumes in 3D) and their distributions are obtained from the numerical simulation. Correlation analysis is then performed to relate the block sizes predicted by the empirical equation to those obtained from the numerical model simulation. The results support the concept of equivalent block size proposed by Cai et al. (2004, Int. J. Rock Mech. Min. Sci., 41(1), 3–19).     

Effects of natural and calcined poultry waste on Cd, Pb and As mobility in contaminated soil

The reuse of waste materials as soil additives could be a welcome development in soil remediation. The mobility of Cd, Pb and As in a contaminated soil was investigated using natural and calcined poultry wastes (eggshell and chicken bone), CaCO₃ and CaO at different application rates (0, 1, 3 and 5 %). The chemical composition accompanied with mineralogical composition indicated that CaCO₃ and CaO were the major components in natural and calcined eggshells, respectively, while hydroxyapatite (HAP) dominated the natural and calcined chicken bones. The results showed that soil pH tended to increase in response to increasing application rates of all soil additives. The effectiveness of the additives in reducing Cd, Pb and As mobility was assessed by means of chemical extractions with 0.1 N HCl for Cd and Pb or 1 N HCl for As, according to Korean Standard Test (KST) method. Both calcined eggshell and chicken bone were equally effective with CaO or CaCO₃ in reducing the concentration of 0.1 N HCl-extractable Cd from 6.17 mg kg^?1 to below warning level of 1.5 mg kg^?1, especially at the highest application rate. The application of calcined eggshell, CaO and CaCO₃ also decreased the concentration of 0.1 N HCl-extractable Pb from 1,012 mg kg^?1 to below warning level of 100 mg kg^?1. The Pb concentration decreased significantly with an increasing application rate of chicken bone, but remained above warning level even at the highest application rate. On the contrary, natural and calcined chicken bones led to a significant increase in the mobility of As when compared with the control soil. These findings illustrate that calcined eggshell in particular is equally effective as pure chemical additives in stabilizing Cd and Pb in a contaminated agricultural soil. The presence of As in metal-contaminated soils should be taken into consideration when applying phosphate-containing materials as soil additives, because phosphate can compete with arsenate on adsorption sites and result in As mobilization.     

Impact of the thermal state of the tropical western Pacific on onset date and process of the South China Sea summer monsoon

Since the early or late onset of the South China Sea summer monsoon （SCSM） has a large impact on summer monsoon rainfall in East Asia, the mechanism and process of early or late onset of the SCSM are an worthy issue to study. In this paper, the results analyzed by using the observed data show that the onset date and process of the SCSM are closely associated with the thermal state of the tropical western Pacific in spring. When the tropical western Pacific is in a warming state in spring, the western Pacific subtropical high shifts eastward, and twin cyclones are early caused over the Bay of Bengal and Sumatra before the SCSM onset. In this case, the cyclonic circulation located over the Bay of Bengal can be early intensified and become into a strong trough. Thus, the westerly flow and convective activity can be intensified over Sumatra, the Indo-China Peninsula and the South China Sea （SCS） in mid-May. This leads to early onset of the SCSM. In contrast, when the tropical western Pacific is in a cooling state, the western Pacific subtropical high anomalously shifts westward, the twin cyclones located over the equatorial eastern Indian Ocean and Sumatra are weakened, and the twin anomaly anticyclones appear over these regions from late April to mid-May. Thus, the westerly flow and convective activity cannot be early intensified over the Indo-China Peninsula and the SCS. Only when the western Pacific subtropical high moves eastward, the weak trough located over the Bay of Bengal can be intensified and become into a strong trough, the strong southwesterly wind and convective activity can be intensified over the Indo-China Peninsula and the SCS in late May. Thus, this leads to late onset of the SCSM. Moreover, in this paper, the influencing mechanism of the thermal state of the tropical western Pacific on the SCSM onset is discussed further from the Walker circulation anomalies in the different thermal states of the tropical western Pacific.     

Satellite and ground observations for large-scale air pollution transport in the Yellow Sea region

Large-scale air pollution transport (LSAPT) in the Yellow Sea region and their inflow onto the Korean Peninsula were observed through satellite images and ground measurements. LSAPT includes regional continental air-masses saturated with pollutants originating from China and subsequently landing on or passing through the Korean Peninsula. It is also possible to identify the distribution and transport patterns of LSAPT over the Yellow Sea. The ground concentrations for PM10, PM2.5 and CO measured at Cheongwon, located in the centre of south Korea, were compared with NOAA satellite images. Notably, the episodes observed of the LSAPT show a PM2.5 to PM10 ratio of 74% of the daily maximum concentrations. However, cases of duststorms were clearly distinguished by much higher PM10 concentrations and a ratio of 30% of PM2.5 to PM10 for daily maximum concentrations. For the episode on January 27, 2006, the inflow of a regionally polluted continental air-mass into the central and southwestern regions of the Korean Peninsula was observed sequentially at various ground observatories as well as by satellite. The north airflow dissipated the clouds over Mt. Halla on Jeju Island and further downwind, reducing air pollution and creating a von Kármán vortex.     

Impact of vegetation feedback on the temperature and its diurnal range over the Northern Hemisphere during summer in a 2 × CO2 climate

This study examines the potential impact of vegetation feedback on the changes in the diurnal temperature range (DTR) due to the doubling of atmospheric CO₂ concentrations during summer over the Northern Hemisphere using a global climate model equipped with a dynamic vegetation model. Results show that CO₂ doubling induces significant increases in the daily mean temperature and decreases in DTR regardless of the presence of the vegetation feedback effect. In the presence of vegetation feedback, increase in vegetation productivity related to warm and humid climate lead to (1) an increase in vegetation greenness in the mid-latitude and (2) a greening and the expansion of grasslands and boreal forests into the tundra region in the high latitudes. The greening via vegetation feedback induces contrasting effects on the temperature fields between the mid- and high-latitude regions. In the mid-latitudes, the greening further limits the increase in T _max more than T _min, resulting in further decreases in DTR because the greening amplifies evapotranspiration and thus cools daytime temperature. The greening in high-latitudes, however, it reinforces the warming by increasing T _max more than T _min to result in a further increase in DTR from the values obtained without vegetation feedback. This effect on T _max and DTR in the high latitude is mainly attributed to the reduction in surface albedo and the subsequent increase in the absorbed insolation. Present study indicates that vegetation feedback can alter the response of the temperature field to increases in CO₂ mainly by affecting the T _max and that its effect varies with the regional climate characteristics as a function of latitudes.     

Climate change in the 21st century simulated by HadGEM2-AO under representative concentration pathways

We present climate responses of Representative Concentration Pathways (RCPs) using the coupled climate model HadGEM2-AO for the Coupled Model Intercomparison Project phase 5 (CMIP5). The RCPs are selected as standard scenarios for the IPCC Fifth Assessment Report and these scenarios include time paths for emissions and concentrations of greenhouse gas and aerosols and land-use/land cover. The global average warming and precipitation increases for the last 20 years of the 21st century relative to the period 1986-2005 are +1.1°C/+2.1% for RCP2.6, +2.4°C/+4.0% for RCP4.5, +2.5°C/+3.3% for RCP6.0 and +4.1°C/+4.6% for RCP8.5, respectively. The climate response on RCP 2.6 scenario meets the UN Copenhagen Accord to limit global warming within two degrees at the end of 21st century, the mitigation effect is about 3°C between RCP2.6 and RCP8.5. The projected precipitation changes over the 21st century are expected to increase in tropical regions and at high latitudes, and decrease in subtropical regions associated with projected poleward expansions of the Hadley cell. Total soil moisture change is projected to decrease in northern hemisphere high latitudes and increase in central Africa and Asia whereas near-surface soil moisture tends to decrease in most areas according to the warming and evaporation increase. The trend and magnitude of future climate extremes are also projected to increase in proportion to radiative forcing of RCPs. For RCP 8.5, at the end of the summer season the Arctic is projected to be free of sea ice.