Behavior of soil plugs in open‐ended model piles driven into sands

Calibration chamber tests were conducted on open‐ended model piles driven into dried siliceous sands with different soil conditions in order to clarify the effect of soil conditions on load transfer mechanism in the soil plug. The model pile used in the test series was devised so that the bearing capacity of an open‐ended pile could be measured as three components: outside shaft resistance, plug resistance, and tip resistance. Under the assumption that the unit shaft resistance due to pile‐soil plug interaction varies linearly near the pile tip, the plug resistance was estimated. The plug capacity, which was defined as the plug resistance at ultimate condition, is mainly dependent on the ambient lateral pressure and relative density. The length of wedged plug that transfers the load decreases with the decrease of relative density, but it is independent of the ambient pressure and penetration depth. Under several assumptions, the value of earth pressure coefficient in the soil plug can be calculated. It gradually reduces with increase in the longitudinal distance from the pile tip. At the bottom of the soil plug, it tends to decrease with increase in the penetration depth and relative density, and to increase with the increase of ambient pressure. This may be attributed to (1) the decrease of friction angle as a result of increase in the effective vertical stress, (2) the difference in the dilation degree of the soil plug during driving with ambient pressures, and (3) the difference in compaction degree of soil plug during driving with relative densities. Based on the test results, an empirical equation was suggested to compute the earth pressure coefficient to be used in the calculation of plug capacity using one‐dimensional analysis, and it produces proper plug capacities for all soil conditions.     

Midlittoral polychaete communities in the Eastern Mediterranean Sea: new information from the implementation of the Natural Geography in Shore Areas (NaGISA) protocol and comparisons at local and regional scales

The aim of this study was to attempt to fill current knowledge gaps on midlittoral Mediterranean biodiversity at local and regional scales, by using benthic polychaetes as a model taxon. Two different data sets were analysed: (i) a quantitative data set from the two Natural Geography in Shore Areas (NaGISA) study sites in Crete and (ii) a qualitative data set from multiple sites across the Mediterranean. At the local scale, the results provide evidence that (i) discrete species communities are formed in midlittoral Mediterranean habitats, which vary by geographical location and year, depending on the scale of observation; (ii) macrophyte coverage and Chl‐a are the only environmental variables associated, albeit weakly, with the above pattern; (iii) although naturally disturbed, the Cretan NaGISA sites do not seem to experience any anthropogenic stress; (iv) environmental heterogeneity and history seem to be much less important in shaping the polychaete communities than inter‐specific interactions; however, it is not possible to specify at this stage whether local or regional processes or even their interactions may shape the polychaete communities. At the regional scale, the results indicate that (i) the only factor that seems to be involved in the regional pattern is the identity of the study providing the data sets, which implies variability and bias in how research projects are carried out, from the sampling design through to data collection and analysis; (ii) the Cretan NaGISA sites may be considered as representative of the habitat in the Mediterranean, under certain conditions.     

Environmental factors influencing aggregation of manta rays (Manta birostris) off the northeastern coast of the Yucatan Peninsula

Manta rays inhabit tropical, subtropical and temperate waters. Aggregation sites of manta rays have been recognized worldwide, but the reasons for this behavior are still poorly understood. This study describes environmental factors influencing aggregation sites of the giant manta ray (Manta birostris) off the northeastern coast of the Yucatan Peninsula. Observations of manta rays were obtained from scientific surveys conducted during 2006–2011. Environmental data were obtained from satellite imagery. The maximum entropy (Maxent) method for habitat modeling was used to determine the effects of environmental conditions on the species and predict suitable habitat for manta rays in this region. Primary productivity and distance to the coast were the most influential variables, suggesting that aggregation occurs in highly productive coastal waters. The distribution of manta rays predicted by the Maxent model showed that the most suitable habitat within the study area is located off the northeastern coast of the Yucatán Peninsula, more precisely, northeast of Isla Holbox and northwest of Isla Contoy. Seasonal patterns of distribution suggest that the most suitable conditions are present from July through September.     

Integrative taxonomic description of Plakina kanaky,a new polychromatic sponge species from New Caledonia (Porifera: Homoscleromorpha)

Four similar sponges of different colors, all unknown to science, were collected in submarine caves of New Caledonia. We aimed at determining whether the four chromotypes represented different species or phenotypic variations of a unique new species. We used an integrative taxonomic approach combining morphologic, molecular and metabolomic analyses. The main traits that define these specimens are a skeleton made of monolophose, trilophose and tetralophose calthrops only, high chemical diversity and a high abundance and diversity of prokaryotic symbionts. The symbiotic community includes two unique prokaryote morphotypes, which are described for the first time in Homoscleromorpha, and appeared to be vertically transmitted. Although several features slightly differ among chromotypes, the most parsimonious conclusion was to propose a single new species Plakina kanaky sp. nov. Our phylogenetic analysis indicated the paraphyly of the Plakina genus, with P. kanaky sp. nov. belonging to a clade that includes Plakina jani and Plakina trilopha. The present work demonstrates that integrative taxonomy should be used in order to revise the entire Plakinidae family and especially the non‐monophyletic genus Plakina.     

Anthropogenic impacts on nitrogen fixation rates between restored and natural Mediterranean salt marshes

To test the effects of site and successional stage on nitrogen fixation rates in salt marshes of the Venice Lagoon, Italy, acetylene reduction assays were performed with Salicornia veneta‐ and Spartina townsendii‐vegetated sediments from three restored (6–14 years) and two natural marshes. Average nitrogen fixation (acetylene reduction) rates ranged from 31 to 343 μmol C₂H₄·m^?2·h^?1 among all marshes, with the greatest average rates being from one natural marsh (Tezze Fonde). These high rates are up to six times greater than those reported from Southern California Spartina marshes of similar Mediterranean climate, but substantially lower than those found in moister climates of the Atlantic US coast. Nitrogen fixation rates did not consistently vary between natural and restored marshes within a site (Fossei Est, Tezze Fonde, Cenesa) but were negatively related to assayed plant biomass within the acetylene reduction samples collected among all marshes. Highest nitrogen fixation rates were found at Tezze Fonde, the location closest to the city of Venice, in both natural and restored marshes, suggesting possible site‐specific impacts of anthropogenic stress on marsh succession.     

Fracture mechanics analysis of multiple cracks in anisotropic media

This paper presents a single‐domain boundary element method (BEM) for linear elastic fracture mechanics analysis in the two‐dimensional anisotropic material. In this formulation, the displacement integral equation is collocated on the un‐cracked boundary only, and the traction integral equation is collocated on one side of the crack surface only. A special crack‐tip element was introduced to capture exactly the crack‐tip behavior. A computer program with the FORTRAN language has been developed to effectively calculate the stress intensity factors of an anisotropic material. This BEM program has been verified having a good accuracy with the previous researches. Furthermore, by analyzing the different anisotropic degree cracks in a finite plate, we found that the stress intensity factors of crack tips had apparent influence by the geometry forms of cracks and media with different anisotropic degrees. Copyright © 2010 John Wiley & Sons, Ltd.     

A new model for the vibration isolation via pile rows consisting of infinite number of piles

In this study, on the basis of the Floquet transform method, a numerical model for the simulation of the vibration isolation via multiple periodic pile rows with infinite number of piles is established. By means of the fictitious pile method due to Muki and Sternberg, the second kind of Fredholm integral equations for the pile rows are developed by using the fundamental solutions for the half‐space and the compatibility conditions between the piles and half‐space. Employing the Floquet transform method, integral equations for the pile rows in the wavenumber domain are then derived. Solution of the integral equations yields the wavenumber domain solution for the pile rows. The space domain solution can then be retrieved by inversion of the Floquet transform. Numerical results show that the proposed model with the Floquet transform method is in a good agreement with those of the conventional direct superposition method. On the basis of the new model, influences of the spacing between neighboring piles, the Young's modulus of the piles, and the pile length on the vibration isolation effect of the pile rows are investigated. Numerical simulations conducted in this study show that compared with the direct superposition method, the efficiency of the proposed model for simulation of the vibration isolation via pile rows is very high. Copyright © 2012 John Wiley & Sons, Ltd.     

The history of water salinity in the Pearl River estuary,China, during the Late Quaternary

This research reconstructed the Late Quaternary salinity history of the Pearl River estuary, China, from diatom records of four sedimentary cores. The reconstruction was produced through the application of a diatom–salinity transfer function developed based on 77 modern surface sediment samples collected across the estuary from shallow marine environment to deltaic distributaries. The statistical analysis indicates that the majority of sediment samples from the cores has good modern analogues, thus the reconstructions are reliable. The reconstructed salinity history shows the older estuarine sequence formed during the last interglacial was deposited under similar salinity conditions to the younger estuarine sequence, which was formed during the present interglacial. Further analysis into the younger estuarine sequence reveals the interplays between sea level, monsoon‐driven freshwater discharge, and deltaic shoreline movement, key factors that have influenced water salinity in the estuary. In particular, a core from the delta plain shows the effects of sea‐level change and deltaic progradation, while cores from the mouth region of the estuary reveal changes of monsoon‐driven freshwater discharge. This study demonstrates the advantages of quantitative salinity reconstructions to improve the quality of reconstruction and allow direct comparison with other quantitative records and the instrumentally observed values of salinity. Copyright © 2010 John Wiley & Sons, Ltd.