考虑弱层置换的岩石边坡稳定性分析

锦屏一级水电站左岸边坡地质结构复杂,岩体存在大量深部裂隙、低波速松弛岩体、煌斑岩脉X及f2、f5断层,严重影响边坡的稳定性。采用基于强度折减法的岩石破裂过程分析RFPA方法对边坡典型部位在开挖后以及其对应弱层置换工况下的破坏全过程进行计算和分析,计算结果表明,f5断层在进行置换加固处理后,边坡安全系数较未置换弱层前提高了0.403,说明在岩质边坡开挖和支护前优先进行深部软弱结构置换处理,可以大大提高工程结构的安全储备。同时,RFPA强度折减法不仅能直观再现边坡潜在滑裂面从萌生到扩展直至贯通导致边坡整体失稳的全过程,而且可以得出边坡安全系数。研究结果对于边坡工程实施前稳定性评价和施工工序具有一定的参考价值。     

单轴条件下层状盐岩的表面裂纹扩展分析

利用荧光法和细观分析技术对单轴条件下层状盐岩表面裂纹扩展及分布进行了研究,并简要分析了国内外盐岩物理力学性质的差异。试验结果表明：纯盐岩表面裂纹以盐晶粒间错动裂纹为主,晶间裂纹扩展贯通形成破坏性主裂纹,裂纹分布受盐晶粒大小及分布均匀性的影响,国外细晶粒盐岩的强度和变形能力均大于国内粗晶粒纯盐岩;纯夹层表面裂纹多产生在几种矿物交杂沉积处,裂纹分布由夹层矿物成分和组成结构决定;含夹层盐岩表面裂纹扩展分布受夹层与盐岩界面过渡形式影响,一般锯齿型交界面裂纹由盐岩部分主裂纹向夹层扩展而成,而过渡分明并含有薄泥层的交界面裂纹由盐岩部分主裂纹和泥层碎散型裂纹汇集扩展而成     

Soft‐sediment deformation structures in Cretaceous non‐marine deposits of southeastern Gyeongsang Basin,Korea: Occurrences and origin

A variety of soft‐sediment deformation structures formed during or shortly after deposition occurs in the Cretaceous Seongpori and Dadaepo Formations of the southeastern Gyeongsang Basin exposed along coastal areas of southeastern Korean Peninsula for 0.5–2 km. These are mostly present in a fluvial plain facies, with interbedded lacustrine deposits. In this study, the features of different kinds of soft‐sediment deformation structures have been interpreted on the basis of sedimentology of structure‐bearing deposits, comparison with normal sedimentary structures, timing and mechanism of deformation, and triggering mechanisms. The soft‐sediment deformation structures can be classified into four morphological groups: (i) load structures (load casts, ball‐and‐pillow structures); (ii) soft‐sediment intrusive structures (dish‐and‐pillars, clastic dykes, sills); (iii) ductile disturbed structures (convolute folds, slump structures); and (iv) brittle deformation structures (syndepositional faulting, dislocated breccia). The most probable triggering mechanisms resulting in these structures were seismic shocks. These interpretations are based on the following field observations: (i) location of the study area within tectonically active fault zone reactivated several times during the Cretaceous; (ii) deformation structures confined to single stratigraphic levels; (iii) lateral continuity and occurrences of various soft‐sediment deformation structures in the deformed level over large areas; (iv) absence of depositional slope to indicate gravity sliding or slumping; and (v) similarity to the structures produced experimentally. The soft‐sediment deformation structures in the study areas are thus interpreted to have been generated by seismic shocks with an estimated magnitude of M > 5, representing an intermittent record of the active tectonic and sedimentary processes during the development and evolution of two formations from the late Early Cretaceous to the Late Cretaceous.     

Dual inexact fuzzy chance-constrained programming for planning waste management systems

This study develops a dual inexact fuzzy chance-constrained programming (DIFCCP) method for planning municipal solid waste (MSW) management systems. The concept of random boundary interval (RBI) is introduced to address the high uncertain parameters in the studied system. Fuzzy flexible programming and chance-constrained programming are also introduced to take into account the uncertainties of RBIs and various uncertainties in MSW management system. Compared with the existing methods, the developed method could deal with the uncertainty without simplification and thus is more robust. Moreover, the potential system-failure risks in MSW management system due to the existing uncertainties could be quantified by means of violation levels and satisfaction levels in DIFCCP. The developed method then is applied to a MSW management system. The obtained solutions could be used for generating efficient management schemes. The values of violation and satisfaction levels could help decision makers understand the tradeoffs between system cost and system-failure risk, and identify desired strategy according to the practical economic and environmental situation.     

Influence of aquatic plants on the hydrogen isotope composition of sedimentary long-chain n-alkanes in the Lake Qinghai region,Qinghai-Tibet Plateau

The hydrogen isotopic composition(δD) of leaf wax long-chain n-alkanes(C27, C29, and C31) from lacustrine sediments has been widely applied to reconstruct terrestrial paleoclimatic and paleohydrological changes. However, few studies have addressed whether the aquatic-derived n-alkanes can affect the δD values of lake sedimentary long-chain n-alkanes, which are usually regarded as a recorder of the terrestrial hydrological signals. Here we systematically investigated δD values of long-chain n-alkanes from modern aquatic plants, both near-shore and off-shore surface sediments, surrounding terrestrial plant litters, as well as river water and lake water in Lake Qinghai and its satellite lakes on the northeastern Qinghai-Tibet Plateau. Our data showed that(i) δD values of long-chain n-alkanes from aquatic plants varied from-184‰ to-132‰ for n-C27, from-183‰ to-138‰ for n-C29, and from-189‰ to-130‰ for n-C31, respectively, with no significant differences among the three n-alkanes homologues;(ii) δD values of long-chain n-alkanes from aquatic plants were generally more positive than those from surrounding terrestrial plants, possibly because that they recorded the D-enrichment of lake water in this semi-arid region;(iii) δD values of long-chain n-alkanes from surface sediments showed significant differences among the three n-alkanes homologues, due to the larger aquatic input of n-C27 to the sedimentary lipid pool than that of n-C31, and(iv) n-C27 δD values of near-shore aquatic plants and near-shore sediments are more negative than those from off-shore as a result of lower δD values of near-shore lake water. Our findings indicate that in this region(i) the offset between sedimentary n-C27 and n-C31 δD values(ΔδDC27-C31) could potentially be used to evaluate if sedimentary long-chain n-alkanes are derived from a single source;(ii) while δD values of n-C27 may be influenced by lake water hydrological changes, sedimentary n-C31 is derived predominantly from terrestrial plants and thus its δD can serve as a relatively reliable indicator for terrestrial paleoclimatic and paleohydrological reconstructions.     

南堡凹陷南部沙一段控砂模式

南堡凹陷盆地内部构造特征复杂,砂体时空分布差异较大。为了明确砂体分布规律,首先对南部缓坡带构造-沉积背景进行研究和岩心相观察,识别了沙一段辫状河三角洲前缘砂体;进而通过对南部缓坡带层序地层格架的建立、沉积学研究和地震地质解释,发现沙一段砂体同时受到顺源和逆源两种同沉积断裂坡折带类型控制。其中,顺源坡折带控制了断槽物源通道的走向,逆源坡折带改变了水流的流向,阻止了砂体的运移。据此,建立了南堡凹陷南部缓坡带沙一段同沉积断裂的控砂模式,得出沙一段砂体具有"沙垒田凸起供砂,断槽物源通道输砂,逆源坡折带阻砂和同沉积洼槽带聚砂"的发育特点。     

挤密条件下U型地埋管换热器换热效率的理论分析及数值模拟

土层的导热系数是影响地源热泵地埋管换热器换热效率的重要因素之一,与土样的密度密切相关。为了提高地源热泵换热器换热效率,本文基于柱热源理论,建立了挤密钻进条件下换热器的传热理论模型,对换热器的换热效率进行了计算,并利用Ansys有限元软件对土层挤密条件下换热器的换热效果进行了数值分析。结果表明,与传统方法相比,土层挤密可有效降低钻孔周围的热阻,U型管换热器的换热效率可提高17%~20%。     

2000-2012年陕甘宁黄土高原区地表蒸散时空分布及影响因素

分析陕甘宁黄土高原区地表蒸散变化特征及其影响因素,可以为区域水资源规划、生态环境改善提供依据。本文利用MOD16蒸散数据,统计分析了陕甘宁黄土高原区2000-2012年地表实际蒸散量的时空变化特征,并结合国家气象站点观测数据和基于像元的相关分析法探讨了其影响因素。结果表明:(1) 2000-2002年蒸散量迅速上升,在2003年达到最高值378.6 mm, 2003-2006年蒸散量呈下降趋势,2006年之后蒸散量呈现缓慢上升趋势。(2) 近13年来,陕甘宁黄土高原区多年平均蒸散量具有明显的空间差异,蒸散量自西北至东南递增,最南部的六盘山、子午岭、黄龙山地是3个主要的高值区;年蒸散量以夏季最多,其次是春季,秋季和冬季最少,且季节蒸散的分布与年蒸散的空间分布格局基本一致。(3) 陕甘宁黄土高原区蒸散量草地和耕地的贡献率最高,密灌丛、疏灌丛次之,常绿针叶林、森林草原贡献率则较小。(4) 陕甘宁黄土高原区动力因素对地表蒸散量影响以正相关为主,风速对该区影响较大;热力因素对地表蒸散量影响以负相关为主,其中气温与蒸散在空间上呈负相关的区域较大,日照时数与蒸散在空间上的负相关区域的面积次之;水分条件(降水量、相对湿度)对蒸散的影响也以正相关为主。     

CRD法开挖对海底隧道结构内力及安全系数影响

翔安隧道是我国第一条大跨度公路海底隧道,其两端陆域段位于富水的强风化岩层中,地质条件极为复杂,设计采用分部开挖法施工,并在隧道施工期间,利用振弦式钢筋计对隧道初期支护及临时支护的钢支撑进行了应力监控。论文基于现场监测数据,并结合数值方法,分别对CRD1、CRD2部和CRD1、CRD3部超前的两种不同开挖顺序对隧道支护结构内力的影响进行了探讨。研究结果表明,采用CRD1、CRD2部超前开挖时的结构内力要略大于采用CRD1、CRD3部超前开挖时的结果,CRD3部的开挖对结构内力的影响较大,两种开挖顺序的安全系数都满足规范要求,所以结构是安全的。     

礁滩体与建设性成岩作用

礁、礁丘、丘同属碳酸盐建隆,礁、滩是重要勘探目的层。但各自在沉积组分、组构、环境和时空分布,以及油气地质条件上迥然不同,因而无论从理论还是勘探实践上,都有必要将其各成体系划分开来。礁滩自身为好储集岩,当建设性成岩作用叠加后可形成好的储层。碳酸盐岩优质储层形成,主要受沉积微相与建设性成岩作用两大因素控制。前者是基础,并以高能的礁滩相带为最好;后者主要包括破裂、白云石化和溶蚀三大类,并以白云石化或溶蚀为最优,其中的溶蚀分布最广泛、影响最深刻而对优质储层形成起决定性作用。礁滩储层中的古岩溶类型最为丰富多彩,包括同生期、准同生期、表生期和埋藏期热流体岩溶的所有类型,白云岩化礁滩体也不例外。其中,同生-准同生期岩溶的形成机制与礁滩沉积时高频层序旋回向上变浅序列的短暂暴露淋溶有关,表生期岩溶则受控于礁滩沉积后三级层序旋回Ⅰ型界面的暴露淋溶。由此,导致礁滩储层中除了可以也是(碳酸盐岩中)唯一保存原生孔隙外,还发育了次生溶蚀孔洞缝和大型溶洞。礁丘、灰泥丘尤其是丘间洼地中发育高有机质丰度烃源岩;它们自身没有有效的原生孔隙,但岩溶作用可以形成次生孔隙。