Atmospheric tracer monitoring and surface plume development at the ZERT pilot test in Bozeman,Montana, USA

A controlled release of CO₂ was conducted at a field site in Bozeman, Montana, USA in July of 2008 in a multi-laboratory study of near surface transport and detection technologies. The development of a subsurface CO₂ plume near the middle packer section of the horizontal release was studied using soil-gas and surface flux measurements of CO₂. A perfluorocarbon tracer was added to the CO₂ released from this section of the horizontal well, and the development of atmospheric plumes of the tracer was studied under various meteorological conditions using horizontal and vertical grids of monitors containing sorbent material to collect the tracer. This study demonstrated the feasibility of using remote sensing for the ultra low level detection of atmospheric plumes of tracers as means to monitor the near surface leakage of sequestered CO₂.     

Using simulated hydrologic response to revisit the 1973 Lerida Court landslide

Hydrologically driven mass wasting in the form of landslides on steep slopes is a worldwide occurrence. High-profile events in, for example, Brazil, Chile, the Philippines, Puerto Rico, and Venezuela during the last three decades all clearly illustrate, based upon significant losses of life and property, that hydrologically driven slope instability in developed (urban) areas can be a major geologic/environmental hazard. The focus of this study is the 1973 hydrologically driven Lerida Court landslide in Portola Valley, CA, USA. Physics-based hydrologic-response simulation, with the comprehensive Integrated Hydrology Model, was employed to forensically estimate the spatiotemporal pore pressure distributions for the Lerida Court site. Slope stability, driven by the simulated pore pressure dynamics, was estimated for the Lerida Court site with the infinite slope/Factor of Safety approach. The pore pressure dynamics for the Lerida Court site were reasonably captured by the hydrologic-response simulation. The estimated time of slope failure for the Lerida Court site compares well with field observations. A recommendation is made that hydrologically driven slope stability estimates including variably saturated subsurface flow be standard protocol for development sites in steep urban settings.     

Phytoplankton diversity in a tropical bay,North Borneo,Malaysia as revealed by light microscopy and Next-Generation Sequencing

Assessments of phytoplankton diversity in Sabah waters, North Borneo, have primarily relied on morphology-based identification, which has inherent biases and can be time-consuming. Next-Generation Sequencing (NGS) technology has been shown to be capable of overcoming several limitations of morphology-based methods. Samples were collected from the Sepanggar Bay over the course of the year 2018 in different monsoon seasons. Morphology-based identification and NGS sequencing of the V8–V9 region of the 18S LSU rDNA were used to investigate the diversity of the phytoplankton community. Microscopy and NGS showed complementary results with more diatom taxa detected by microscopy whereas NGS detected smaller and rarer taxa. The harmful algal genera in the study site comprised of Skeletonema, Margalefidinium, Pyrodinium, Takayama, and Alexandrium as detected by NGS. This study showed that that an integrative approach of both morphological and molecular techniques could provide more comprehensive information about the phytoplankton community as the approach captured quantitative variability as well as the diversity of phytoplankton species.     

The water impacts of climate change mitigation measures

A variety of proposed activities to mitigate greenhouse gas emissions will impact on scarce water resources, which are coming under increasing pressure in many countries due to population growth and shifting weather patterns. However, the integrated analysis of water and carbon impacts has been given limited attention in greenhouse mitigation planning. In this Australian case study, we analyse a suite of 74 mitigation measures ranked as highest priority by one influential analysis, and we find that they have highly variable consequences for water quantity. We find: (1) The largest impacts result from land-based sequestration, which has the potential to intercept large quantities of water and reduce catchment yields, estimated to exceed 100 Mm³/MtCO₂-e of carbon mitigated (100,000 l per tonne CO₂-e). (2) Moderate impacts result from some renewable power options, including solar thermal power with a water cost estimated at nearly 4 Mm³/MtCO₂-e. However, the water impacts of solar thermal power facilities could be reduced by designing them to use existing power-related water supplies or to use air or salt-water cooling. (3) Wind power, biogas, solar photovoltaics, energy efficiency and operational improvements to existing power sources can reduce water demand through offsetting the water used to cool thermal power generation, with minor savings estimated at 2 Mm³/MtCO₂-e and amounting to nearly 100 Mm³ of water saved in Australia per annum in 2020. This integrated analysis significantly changes the attractiveness of some mitigation options, compared to the case where water impacts are not considered.     

四川盆地震旦系灯影组葡萄状白云岩成因

四川盆地震旦系灯影组发育巨厚的白云岩,其中灯影组二段和四段发育大量具有各种形态的葡萄状白云岩,其直径最长可达75cm,有的平行于层面,有的穿层。剖面资料表明,葡萄状白云岩发育多期等厚环边胶结物,中部残留大量未充填的不规则洞穴,这成为与岩溶喀斯特作用相关的地下溶蚀作用的证据。围岩泥晶白云石为早期海水中原生结晶的产物,后来的胶结物可划分为4期: (1)自泥晶化白云石(部分样品中可见)作为最早的一期胶结物,由于各种生物化学作用和生物作用的影响而紧贴着围岩发育;(2)第2期胶结物纤维状白云石可能为海水中直接沉淀的产物,经历后期成岩作用后,具有完全有序的结构,晶胞参数接近理想值;(3)细—中晶白云石为第3期胶结物,包含纤维状白云石溶蚀残余,形成于构造抬升之后的近地表大气淡水环境;(4)第4期胶结物中—粗晶白云石为埋藏环境下直接结晶的产物,充填了孔洞中心,残留部分未充填孔洞。灯影组受到了岩溶喀斯特作用、胶结作用以及白云石化作用等成岩作用的影响,其中与葡萄状白云岩有关的岩溶喀斯特作用对于灯影组储集层的发育至关重要。对灯影组葡萄状白云岩的研究,不仅有助于深入探讨灯影组储集层成因和演化及灯影组白云岩的成因,而且有助于指导四川盆地前寒武系油气勘探。     

Appraising stone column settlement prediction methods using finite element analyses

Numerous approaches exist for the prediction of the settlement improvement offered by the vibro-replacement technique in weak or marginal soil deposits. The majority of the settlement prediction methods are based on the unit cell assumption, with a small number based on plane strain or homogenisation techniques. In this paper, a comprehensive review and assessment of the more popular settlement prediction methods is carried out with a view to establishing which method(s) is/are in best agreement with finite element predictions from a series of PLAXIS 2D axisymmetric analyses on an end-bearing column. The Hardening Soil Model in PLAXIS 2D has been used to model the behaviour of both the granular column material and the treated soft clay soil. This study has shown that purely elastic settlement prediction methods overestimate the settlement improvement for large modular ratios, while the methods based on elastic–plastic theory are in better agreement with finite element predictions at higher modular ratios. In addition, a parameter sensitivity study has been carried out to establish the influence of a range of different design parameters on predictions obtained using a selection of elastic–plastic methods.     

The application of chromatographic gas ratio analysis in reservoir fluid evaluation of “Beta” field in the Congo basin

This study assessed the hydrocarbon generation potentials/timing of the Awgu source rock horizons encountered in Igbariam-1, Iji-1 and Ajire-1 wells drilled in the southern Benue Trough; using one-dimensional (1D) Genesis Zetaware basin modelling software. This software enabled the integration of burial and thermal influences on Awgu source rocks with kinetic parameters. Thermal and burial history models indicate that the Awgu source horizons encountered at 3249m in Igbariam-1 well (northern part of the basin), expelled 85mg/gtoc of oil and 12 mg/gtoc of gas and hydrocarbon generation began in early Eocene with maximum expulsion in the mid-Eocene (52my) at the rate of 7mg/gtoc/my. To the south of the basin, the Awgu source horizons were encountered at greater depths in Iji-1 and Ajire-1 wells and hydrocarbon generation began in the mid-Palaeocene and peaked in the late Palaeocene (58my) at the rate of 32–38mg/gtoc/my. This resulted in an increase in generated hydrocarbon volume to the south due to (a) increased burial depth and early maturation, and (b) changing source lithofacies -more marine. The fault system linking potential reservoirs such as the Agbani sandstone and the overlying Owelli sandstone to the source rock suggests a possible migration of the generated hydrocarbons to those reservoirs at that time.     

The thermodynamic speed limit and its violation in axisymmetric numerical simulations of tornado‐like vortices

Abstract

Processes that regulate the central pressure and maximum wind speeds of tornado‐like vortices are explored with an axisymmetric numerical model. The model consists of a rotating cylinder of fluid enclosed within rigid boundaries. The momentum diffusivity is a fixed function of height. In the rotating reference frame, relative motion is induced by a buoyancy force in the vicinity of the rotation axis, leading to the formation of a central vortex. The work done by the central buoyancy force on a parcel rising along the axis defines theoretical and empirical wind speed bounds on both the updraft and the low‐level vortex. Certain processes are found that allow for the vortex to greatly exceed this wind speed bound, or the so‐called thermodynamic speed limit; however, in most of the parameter space the vortex wind speeds are close to the thermodynamic speed limit.

The most effective limit‐breaking process involves a supercritical end‐wall vortex with an axial jet. In steady state, the supercritical vortex sustains wind speeds 2.0 times the speed limit. A transient end‐wall vortex, with the vortex breakdown travelling rapidly downwards toward the surface, is able to achieve wind speeds 5.0 times the speed limit. Warming of the subsiding vortex core past the vortex breakdown increases the maximum steady‐state azimuthal wind speed by about 20% from what it would be otherwise. Axial momentum diffusion is not found to significantly enhance the surface pressure deficit in any of the simulations.     

Spatial interpolation of snow water equivalency using surface observations and remotely sensed images of snow‐covered area

As demand for water continues to escalate in the western Unites States, so does the need for accurate monitoring of the snowpack in mountainous areas. In this study, we describe a simple methodology for generating gridded‐estimates of snow water equivalency (SWE) using both surface observations of SWE and remotely sensed estimates of snow‐covered area (SCA). Multiple regression was used to quantify the relationship between physiographic variables (elevation, slope, aspect, clear‐sky solar radiation, etc.) and SWE as measured at a number of sites in a mountainous basin in south‐central Idaho (Big Wood River Basin). The elevation of the snowline, obtained from the SCA estimates, was used to constrain the predicted SWE values. The results from the analysis are encouraging and compare well to those found in previous studies, which often utilized more sophisticated spatial interpolation techniques. Cross‐validation results indicate that the spatial interpolation method produces accurate SWE estimates [mean R² = 0·82, mean mean absolute error (MAE) = 4·34 cm, mean root mean squared error (RMSE) = 5·29 cm]. The basin examined in this study is typical of many mid‐elevation mountainous basins throughout the western United States, in terms of the distribution of topographic variables, as well as the number and characteristics of sites at which the necessary ground data are available. Thus, there is high potential for this methodology to be successfully applied to other mountainous basins. Copyright © 2010 John Wiley & Sons, Ltd.     

Observations of the evolution of the aerosol, cloud and boundary‐layer characteristics during the 1st ACE‐2 Lagrangian experiment

During the 1st Lagrangian experiment of the North Atlantic Regional Aerosol Characterisation Experiment (ACE‐2), a parcel of air was tagged by releasing a smart, constant level balloon into it from the Research Vessel Vodyanitskiy . The Meteorological Research Flight's C‐130 aircraft then followed this parcel over a period of 30 h characterising the marine boundary layer (MBL), the cloud and the physical and chemical aerosol evolution. The air mass had originated over the northern North Atlantic and thus was clean and had low aerosol concentrations. At the beginning of the experiment the MBL was over 1500 m deep and made up of a surface mixed layer (SML) underlying a layer containing cloud beneath a subsidence inversion. Subsidence in the free troposphere caused the depth of the MBL to almost halve during the experiment and, after 26 h, the MBL became well mixed throughout its whole depth. Salt particle mass in the MBL increased as the surface wind speed increased from 8 m s⁻¹ to 16 m s⁻¹ and the accumulation mode (0.1μm to 3.0 μm) aerosol concentrations quadrupled from 50 cm⁻³ to 200 cm⁻³. However, at the same time the total condensation nuclei (>3 nm) decreased from over 1000 cm⁻³ to 750 cm⁻³. The changes in the accumulation mode aerosol concentrations had a significant effect on the observed cloud microphysics. Observational evidence suggests that the important processes in controlling the Aitken mode concentration which, dominated the total CN concentration, included, scavenging of interstitial aerosol by cloud droplets, enhanced coagulation of Aitken mode aerosol and accumulation mode aerosol due to the increased sea salt aerosol surface area, and dilution of the MBL by free tropospheric air.