Ripple formation in combined transdirectional steady and oscillatory flow

Measurements are described of the geometry of ripples formed on beds of sand exposed to a steady current at right angles to an oscillatory flow. Four different sands were studied. The oscillation was produced by an oscillating tray set into the bed of a steady-flow flume. It was observed that straight-crested ripples formed by oscillatory flow would usually develop a ‘serpentine’ form when the superimposed steady current exceeded a certain limit. For amplitudes of the tray velocity U_∞ less than about 0.38 m s^-1 this limit corresponded to U_∞/ū_*c>31, where ū_*c is the shear velocity measured just upstream of the oscillating tray. It is suggested that the serpentine form is caused by the interaction of vortices carried back and forth between adjacent ripples. On this assumption, the wavelength of the serpentine form would be proportional to the product of period of oscillation and near-bed steady current velocity. The present measurements appear to support this hypothesis although there is also evidence that the wavelength is influenced by preferred spacing patterns between vortices. The measurements also show the ratio of the amplitude of the serpentine form to its wavelength to be approximately constant. Empirical relationships are derived relating ripple geometry to flow and sediment properties. It is observed that the influence of Reynolds number and sediment properties on the geometry is very weak. It is suggested that this is typical of ripples formed with relatively low sediment transport rates. It is also found that, under the present experimental conditions, the ripple spacing in the direction of oscillation is almost independent of the magnitude of the steady current and in close agreement with the wavelengths previously measured in an oscillating water tunnel. This suggests that the additional inertia effects associated with oscillating tray rigs were not sufficient to affect bed geometry under the present test conditions.     

Sheetflow fluvial processes in a rapidly subsiding basin, Altiplano plateau, Bolivia

Although facies models of braided, meandering and anastomosing rivers have provided the cornerstones of fluvial sedimentology for several decades, the depositional processes and external controls on sheetflow fluvial systems remain poorly understood. Sheetflow fluvial systems represent a volumetrically significant part of the non‐marine sedimentary record and documented here are the lithofacies, depositional processes and possible roles of rapid subsidence and arid climate in generating a sheetflow‐dominated fluvial system in the Cenozoic hinterland of the central Andes. A 6500 m thick succession comprising the Late Eocene–Oligocene Potoco Formation is exposed continuously for >100 km along the eastern limb of the Corque syncline in the high Altiplano plateau of Bolivia. Fluvial sandstone and mudstone units were deposited over an extensive region (>10 000 km²) with remarkably few incised channels or stacked‐channel complexes. The Potoco succession provides an exceptional example of rapid production of accommodation sustained over a prolonged period of time in a non‐marine setting (>0·45 mm year⁻¹ for 14 Myr). The lower ≈4000 m of the succession coarsens upward and consists of fine‐grained to medium‐grained sandstone, mudstone and gypsum deposits with palaeocurrent indicators demonstrating eastward transport. The upper 2500 m also coarsens upward, but contains mostly fine‐grained to medium‐grained sandstone that exhibits westward palaeoflow. Three facies associations were identified from the Potoco Formation and are interpreted to represent different depositional environments in a sheetflow‐dominated system. (i) Playa lake deposits confined to the lower 750 m are composed of interbedded gypsum, gypsiferous mudstone and sandstone. (ii) Floodplain deposits occur throughout the succession and include laterally extensive (>200 m) laminated to massive mudstone and horizontally stratified and ripple cross‐stratified sandstone. Pedogenic alteration and root casts are common. (iii) Poorly confined channel and unconfined sheet sandstone deposits include laterally continuous beds (50 to >200 m) that are defined primarily by horizontally stratified and ripple cross‐stratified sandstone encased in mudstone‐rich floodplain deposits. The ubiquitous thin‐sheet geometry and spatial distribution of individual facies within channel sandstone and floodplain deposits suggest that confined to unconfined, episodic (flash) flood events were the primary mode of deposition. The laterally extensive deposition and possible distributary nature of this sheetflow‐dominated system are attributed to fluvial fan conditions in an arid to semi‐arid, possibly seasonal, environment. High rates of sediment accumulation and tectonic subsidence during early Andean orogenesis may have favoured the development and long‐term maintenance of a sheetflow system rather than a braided, meandering or anastomosing fluvial style. It is suggested here that rapidly produced accommodation space and a relatively arid, seasonal climate are critical conditions promoting the generation of sheetflow‐dominated fluvial systems.     

Time and space distribution of megaripples and associated bedforms, Middle Atlantic Bight, North American Atlantic Shelf

Three genetically distinct size classes of lower regime transverse bedforms have long been known from laboratory studies, and from studies of the intertidal zone; ripples, megaripples, and sand waves. These features are also present on the subtidal shelf surface of the Middle Atlantic Bight, and their distribution in time and space allows us to draw inferences concerning the time and space pattern of sediment transport. Transverse bedforms in the Middle Atlantic Bight occur in response to tidal flows at estuary and inlet mouths and on tide-dominated banks; on the shelf surface, however, they are primarily responses to wind-driven flows. Ripples are the most widespread of the three classes. They are current-formed during peak storm flows, but are probably remade as oscillatory wave ripples as the flow wanes. Megaripples are found primarily on the inner shelf, also as responses to peak storm flows. Sand waves of several metres amplitude occur on the inner shelf in the vicinity of topographic highs; low amplitude sand waves (< 2m), solitary or in trains, are widespread on the inner shelf. They survive through many seasons of storm flows. Megaripples are especially interesting as records of specific flow events. They are widespread on the inner shelf during the winter, occurring in fields up to several kilometres in diameter. On a portion of the Long Island inner shelf during December 1976, megaripple fields covered approximately 15% of the shelf surface. They tend to be erased during the succeeding summer months. Both megaripples (short-term response elements) and sand waves (long-term response elements) indicate that sand transport in the Middle Atlantic Bight is directed to the southeast, parallel with the regional trend of the isobaths.     

Sediment suspension under waves and currents: time scales and vertical structure

Field measurements of the vertical structure of near-bed suspended sediment concentrations were obtained from arrays of fast response optical backscatter suspended solids sensors to examine the time-dependent response of sediment resuspension to waves and currents and the constraints imposed by bedforms. Data were recorded from both a nonbarred, marine shoreface and a barred lacustrine shoreface, under both shoaling and breaking waves (significant heights of 0·25–1·50m; peak periods of 3 and 8 s) and in water depths of 0·5–5·0 m. Sediment concentrations are positively correlated with increasing elevation above the bed, but lagged in time. The time lag varies directly with separation distance between measurement locations and inversely with the horizontal component of the near-bed oscillatory velocity. Both the presence of wave groups and the settling velocities of the sediment particules in suspension influence the temporal changes in concentration at a given elevation. Sediment concentrations appear to respond more slowly to the incident wind-wave forcing with distance away from the bed as a result of two factors: (1) the sequential increase in concentration induced by a succession of large waves in a group; and (ii) the relative increase in finer sediments with smaller settling velocities. Bedforms interact with the near-bed horizontal currents to impose a distinct constraint upon the timing of suspension events relative to the phase of the fluid motion, and, therefore, the vertical structure of the suspended sediment concentration at a range of time scales. The near-bed concentrations appear to be strongly dependent upon the vertical convection of sediment associated with the ejection from the wave boundary layer of separation vortices generated in the lee of ripple crests. Concentration gradients in the presence of vortex ripples are large, as are the correlation between concentrations measured at different elevations within the fluid.     

Middle and late Cenomanian oceanic anoxic events in shallow and deeper shelf environments of western Morocco

The response of shallow‐water sequences to oceanic anoxic event 2 and mid‐Cenomanian events 1a and 1b was investigated along the west African margin of Morocco north of Agadir (Azazoul) and correlated with the deep‐water sequence of the Tarfaya Basin (Mohammed Beach) based on biostratigraphy, mineralogy, phosphorus and stable isotopes. In the deeper Mohammed Beach section results show double peaks in δ¹³C_org for mid‐Cenomanian events 1a and 1b (Rotalipora reicheli biozone, lower CC10a biozone), the characteristic oceanic anoxic event 2 δ¹³C excursion (Rotalipora cushmani extinction, top of CC10a biozone) and laminated (anoxic) black shale. In the shallow environment north of Agadir, a fluctuating sea‐level associated with dysoxic, brackish and mesotrophic conditions prevailed during the middle to late Cenomanian, as indicated by oyster biostromes, nannofossils, planktonic and benthonic foraminiferal assemblages. Anoxic conditions characteristic of oceanic anoxic event 2 (for example, laminated black shales) did not reach into shallow‐water environments until the maximum transgression of the early Turonian. Climate conditions decoupled along the western margin of Morocco between mid‐Cenomanian event 1b and the Cenomanian–Turonian boundary, as also observed in eastern Tethys. North of Agadir alternating humid and dry seasonal conditions prevailed, whereas in the Tarfaya Basin the climate was dry and seasonal. This climatic decoupling can be attributed to variations in the Intertropical Convergence Zone and in the intensity of the north‐east trade winds in tropical areas.     

Bedload transport of mud as pedogenic aggregates in modern and ancient rivers

Abundant sand-sized mud aggregates in the Cooper and Diamantina Rivers, Lake Eyre Basin, Australia are attributed to bedload transport of aggregates formed in deeply-cracked floodplain soils. The conditions required for formation of pedogenic mud aggregates are: (i) abundant clay containing at least minor swelling clay, and (ii) a climate with at least seasonally hot dry periods. The worldwide distribution of these soils (Vertisols) suggests that a significant amount of mud is transported as pedogenic aggregates by modern rivers. Ancient analogues in which mud aggregates and Vertisol profiles have been recognized are the Jurassic East Berlin Formation (Connecticut, USA) and the Carboniferous Maringouin Formation (New Brunswick and Nova Scotia, Canada). The dominant red mudstones of these formations are interpreted as mainly bedload sediments deposited by sheet floods in semi-arid palaeoclimates. The Triassic Hawkesbury Sandstone (NSW, Australia) also contains sand-sized mudstone aggregates, thought to be pedogenic, but its paleosol and other facies point to formation in a wetter palaeoclimate. The indications are that bedload transport of mud as pedogenic aggregates was as significant a process in ancient rivers as it is at present.     

Early Cambrian reefs, reef complexes, and associated lithofacies of the Shackleton Limestone, Transantarctic Mountains

The Shackleton Limestone formed a carbonate platform that bordered part of the Greater Antarctic craton in middle and late Early Cambrian time. In the Holyoake Range of the central Transantarctic Mountains, this unit records deposition on a stable shelf on which flourished ecological reefs composed of microorganisms and archaeocyathans. Burrow-mottled lime mudstone, wackestone and packstone with patch reefs represent accumulation in shelf areas of relatively low to moderate energy. Thick ooidal grainstone units reflect deposition in higher energy shoals and as sand sheets that were associated with extensive reef complexes. The framework of these reefs was principally the product of micro-organisms, by inference mostly cyanobacteria. Archaeocyathans constitute as much as 30% of some reefs, but commonly they form less than 10% and are absent from some. On the basis of microbial composition, three reef types are recognized. The first type is a Renalcis boundstone that lacks archaeocyathans. Within these, abundant upward-directed thalii of Renalcis formed a framework that trapped fine-grained sediment. The second type, which forms the core of some larger reefs, is composed of stromatactis-bearing, microbial boundstone. The third, yet most common, reef type is variable in composition. It is characterized by the presence of abundant Epiphyton, but may include archaeocyathans, and the microbial microfossils Girvanella and Renalcis as well as cryptomicrobial clotted micrite. In this type of reef, frame-building organisms typically constructed highly porous structures that had small interparticle and fenestral pores and large growth-framework cavities, as well as rare metre-sized caverns. Within these spaces, Epiphyton and, less commonly Renalcis, encrusted framework elements, fine-grained sediments accumulated, and pervasive sea-floor cements were precipitated. Boundstone fabrics in the Shackleton Limestone are highly complex, with fabrics analogous to younger, more metazoan-rich reefs, as well as deep-water stromatactis-bearing mud-mounds. The Epiphyton-Girvanella-archaeocyathan frameworks and stromatactis-bearing boundstones, both of which seemingly first appeared in the middle Early Cambrian, are regarded as the precursors, in structure, composition, and preferred hydrologic setting, of the more extensive reefs and complex framework styles of later Phanerozoic time.     

Petrography and textural development of inorganic and biogenic lithotypes in a relict barite tufa deposit at Flybye Springs, NT, Canada

A relict mound of Holocene barite (BaSO₄) tufa underlies the Flybye Springs, a small, barium‐rich, cold sulphur spring system in the Northwest Territories of Canada. The tufa is composed of relatively pure barite with ≤0·34 wt% Ca²⁺ and ≤0·77 wt% Sr²⁺. The mound is made up of coated bubble, raft, undulatory sheet, stromatolitic, coated grain and detrital conglomerate barite tufa. Although previously unreported in barite, these lithotypes are akin to facies found in many carbonate spring deposits. Raft and ooid‐coated grain tufa was formed via ‘inorganic’ barite precipitation in spring water ponds and tributaries where rapid oxidation of sulphide to sulphate established barite supersaturation. Undulatory sheet tufa may have formed by the reaction of dissolved barium with sulphate derived from the oxidation of extracellular polysaccharide‐rich colloidal sulphur films floating in oxygenated, barite‐saturated spring water ponds. Coated bubble, oncoid‐coated grain and stromatolitic tufa with filamentous microfossils was formed in close association with sulphur‐tolerant microbes inhabiting dysoxic and oxygenated spring water tributaries and ponds. Adsorption of dissolved barium to microbial extracellular polysaccharide probably facilitated the development of these ‘biogenic’ lithotypes. Detrital conglomerate tufa was formed by barite cementation of microdetrital tufa, allochthonous lithoclasts and organic detritus, including caribou hair. Biogenic textures, organic artefacts and microfossils in the Flybye barite tufa have survived diagenetic aggradational recrystallization and precipitation of secondary cements, indicating the potential for palaeoecological information to be preserved in barite in the geological record. Similarities between the Flybye barite tufa and carbonate spring deposits demonstrate that analogous textures can develop in chemical sedimentary systems with distinct mineralogy, biology and physiochemistry.     

A REVIEW OF THE EARLY TERTIARY FORMATIONS OF CHINA~1

INTRODUCTION The Early Tertiary formations in China have not been studied systematically for a long time, since they are less well exposed and less fossilifer, ous than the Pliocene or Pleistocene beds in the same areas. No further re-