Simultaneous operation of the Sea Beam multibeam echo-sounder andthe SeaMARC II bathymetric sidescan sonar system

An experiment aboard the Scripps Institution of Oceanography's RV Thomas Washington has demonstrated the seafloor mapping advantages to be derived from combining the high-resolution bathymetry of a multibeam echo-sounder with the sidescan acoustic imaging plus wide-swath bathymetry of a shallow-towed bathymetric sidescan sonar. To a void acoustic interference between the ship's 12-kHz Sea Beam multibeam echo-sounder and the 11-12-kHz SeaMARC II bathymetric sidescan sonar system during simultaneous operations, Sea Beam transmit cycles were scheduled around SeaMARC II timing events with a sound source synchronization unit originally developed for concurrent single-channel seismic, Sea Beam, and 3.5-kHz profile operations. The scheduling algorithm implemented for Sea Beam plus SeaMARC II operations is discussed, and the initial results showing their combined seafloor mapping capabilities are presented     

Deep-ocean vertical noise directionality

The structure of beam noise measured at the output of a vertical array in a range dependent ocean basin was investigated using the modified wide-angle parabolic equation (PE). Noise sources were distributed throughout the basin, and the field due to each noise source at an array located in the midbasin was calculated. The response of the array to the superposition of the noise sources was found by beamforming. An efficient and direct approach that superimposes the noise sources on the PE field as the field is marched toward the array was developed. Downslope calculations of the midbasin vertical directionality were made between 50 and 400 Hz with this technique. Use of a geoacoustic model shows that the bottom behaves as a low-pass filter     

Inverted echo sounder measurement of dynamic height through an ENSOcycle in the central equatorial Pacific

A four-year record from an inverted echo sounder deployed near Palmyra Island at 6°N in the central Pacific Ocean is compared with a simultaneous record of subsurface pressure from this island lagoon. A factor m, converting round-trip acoustic travel time to surface dynamic height relative to a deep pressure level, was estimated from the ratio of the spectra of the two records in the energetic synoptic oscillation band. Year-to-year variation in m was not statistically significant. For the overall record, m was found to be -70±8 dynamic m/s, where the error bounds represent a 90% confidence interval. This is consistent with first-baroclinic-mode excitation     

Magma homogenization during anatexis,ascent and/or emplacement? Constraints from the Variscan Weinsberg Granites

Recent studies have shown that melts and residues may not equilibrate during anatexis, and uncertainty exists about the scale on which magmas can be homogenized. This study of elemental and isotopic homogeneity of the South Bohemian Weinsberg granites (˜ 5000 km²) identifies three voluminous, relatively homogeneous magma batches. Each batch has different ⁸⁷Sr/⁸⁶Sr_init (0.7080, 0.7093 and 0.7106), but all equilibrated at ˜ 327–329 Ma, very similar to the time of monazite crystallization. The data cannot entirely prove melt/residue equilibration during anatexis. However, elemental and isotopic compositions imply magma generation by partial melting of heterogeneous South Bohemian crust and chemical differentiation subsequent to Sr-isotope equilibration. Assuming relatively rapid ascent and solidification rates, magma homogenization must have occurred mostly just after partial melting, during melt segregation and accumulation in the deeper crust with slow prograde heating. Models of rapid crustal heating and instantaneous melt extraction are incompatible with the data.     

A comparison of type II shock speeds

Type II radio bursts are produced by material moving outwards in the solar atmosphere. Their drift in frequency allows the calculation of the radial speed with which the shock is moving- very basic information in assessing the likelihood that the shock will reach the Earth and its time of arrival. This paper compares the shock speeds derived from radio bursts observed by the Swept Frequency Interferometric Radiometer (SFIR) equipment at the US Air Force Radio Solar Telescope Network (RSTN) of observatories with those measured with the Culgoora radiospectrograph operated by IPS Radio and Space Services. The SFIR shock speeds are found to be 1.5–3.0 times larger than the Culgoora values which are consistent with earlier results. This difference appears to originate from the incorrect interpretation of events as a result of the smaller frequency range of the SFIR equipment.     

Wooden Panel Deterioration by Tropical Marine Wood Borers

Wood destruction in test panels ofShorea leprosulawas related to the percentage of fouling, types of wood borers and the number of wood borers. The natural durability ofShorea leprosulapanels was estimated to be 4–5 months in Malaysian marine waters. A higher fouling cover resulted in lower rates of wooden panel deterioration. Larger numbers of wood borers brought about greater panel deterioration. Primary wood destruction was caused by bivalve wood borers, mainlyMartesia striata, Lyrodus pedicellatus, Bankia campanellata, Teredo furciferaandTeredo bartschi. Martesia striatawas the important wood destroying agent in the intertidal zone and, together with the shipworms, was also responsible for panel destruction in the subtidal zone.     

Simulations of a giant hybrid air shower detector

We have used Monte Carlo simulations to investigate the capabilities of a giant air shower observatory designed to detect showers initiated by cosmic rays with energies exceeding 10¹⁹ eV. The observatory is to consist of an array of detectors that will characterise the air shower at ground level, and optical detectors to measure the fluorescence light emitted by the shower in the atmosphere. Using these detectors together in a ‘hybrid’ configuration, we find that precise geometrical reconstruction of the shower axis is possible, leading to excellent resolution in energy. The technique is also shown to provide very good reconstruction below 10¹⁹ eV, at energies where the ground array is not fully efficient.     

Effect of element size on the static finite element analysis of steep slopes

The accuracy of the computed stress distribution near the free surface of vertical slopes was evaluated in this study as a function of the element size, including aspect ratio. To accomplish this objective, a parametric study was carried out comparing stresses computed using the finite element method (FEM) to those obtained from a physical model composed of photoelastic material. The results of the study indicate a reasonable agreement between a gelatin model and the FEM model for shear stresses, and an overall good agreement between the two models for the principal stresses. For stresses along the top of the slope, the height of the element tends to be more important than width or aspect ratio, at least for aspect ratios up to 4. In all cases, the greatest difference between the two models occurs in the vicinity of the slope. Specifically, if H is defined as the slope height, an element height of H/10 appears to be adequate for the study of stresses deep within the slope, such as for typical embankment analyses. However, for cases where tensile stresses in the vicinity of the slope face which are critical, such as for the stability analysis of steep slopes, element heights as small as H/32, or higher‐order elements, are necessary. Copyright © 2001 John Wiley & Sons, Ltd.