Improved target illumination at Ludvika mines of Sweden through seismic-interferometric surface-wave suppression

In mineral exploration, new methods to improve the delineation of ore deposits at depth are in demand. For this purpose, increasing the signal-to-noise ratio through suitable data processing is an important requirement. Seismic reflection methods have proven to be useful to image mineral deposits. However, in most hard rock environments, surface waves constitute the most undesirable source-generated or ambient noise in the data that, especially given their typical broadband nature, often mask the events of interest like body-wave reflections and diffractions. In this study, we show the efficacy of a two-step procedure to suppress surface waves in an active-source reflection seismic dataset acquired in the Ludvika mining area of Sweden. First, we use seismic interferometry to estimate the surface-wave energy between receivers, given that they are the most energetic arrivals in the dataset. Second, we adaptively subtract the retrieved surface waves from the original shot gathers, checking the quality of the unveiled reflections. We see that several reflections, judged to be from the mineralization zone, are enhanced and better visualized after this two-step procedure. Our comparison with results from frequency-wavenumber filtering verifies the effectiveness of our scheme, since the presence of linear artefacts is reduced. The results are encouraging, as they open up new possibilities for denoising hard rock seismic data and, in particular, for imaging of deep mineral deposits using seismic reflections. This approach is purely data driven and does not require significant judgment on the dip and frequency content of present surface waves, which often vary from place to place.     

Regional improvement of global geopotential models using GPS/Leveling data

Studia Geophysica et Geodaetica - Global geopotential models are widely used in the remove-compute-restore technique for local gravity field modeling. In this paper, a method for regional...     

Paleopedology and magnetic properties of Sari loess-paleosol sequence in Caspian lowland,northern Iran

The objective of this study was to characterize the morphological and magnetic properties of Sari loess-paleosol section in northern Iran for paleopedologic and paleoenvironmental interpretation. The section consisted of a modern soil(MS) and three paleosols(PS_1, PS_2, PS_3) separated by loess layers(LS_1, LS_2 and LS_3). Based on particle size distribution, clay mineralogy, carbonates distribution and size of secondary carbonates, pedogenic development of the soils was in order of PS_3PS_2PS_1=MS. Presence of redoximorphic features in PS_3 was attributed to alternate stagnic saturation due to local water or high precipitation. Dominance of smectite and vermiculite as well as large carbonated dolls in PS_3 indicated suitable environment and sufficient time for pedogenic development. Magnetic properties(χ~(lf) and χ~(fd)%) were distinctly higher in MS, PS_1 and PS_2 when compared to loess layers. The Lowest magnetic properties values were observed in PS_3 which can be the result of ferrimagnetic minerals destruction under hydromorphic conditions. The highest Fe_d content occurred in PS_3, however, low χ~(lf)/Fe_d ratio indicated that majority of the iron minerals in PS_3 are not magnetic. In conclusion, the particle size distribution, clay mineralogy and carbonates features were indicative of pedogenesis intensity, whereas, magnetic properties were useful to characterize the pedogenic environment.     

A Hybrid Particle Swarm Optimization and Genetic Algorithm for Model Updating of A Pier-Type Structure Using Experimental Modal Analysis

China Ocean Engineering - Conventional design of pier structures is based on the assumption of fully rigid joints. In practice, the real connections are semi-rigid that cause changes in dynamic...     

Dynamic mechanism of turbulent flow in meandering channels: considerations for deflection angle

To find turbulent flow structure inside meandering channels, three physical models of river meanders representing strongly curved bend, mild bend and elongated symmetrical meander loop were tested in this paper. Instantaneous velocity data in three dimensions were measured using Micro-ADV at different cross sections of these models. Depth averaged velocity vectors, streamwise velocity, secondary currents, turbulent and mean flow kinetic energy were investigated with respect to the sediment deposition pattern. In order to gain more regarding the force acting the sediment particles, three dimensional velocity fluctuations were analyzed in detailed inside the elongated symmetrical meander loop. Occurrence frequency, transition probability and angle of attack for different events were also computed for the points close to the bed. Of the present results, the importance of sweeps and ejections on sediment deposition can be detected. Further, distribution of bursting events is presented through the water column and compared the results with the previous works. Importantly, occurrence of fluctuating velocities in three dimensions at different locations inside the river meanders in addition to the effect of mean flow and turbulent components is responsible for sediment transport. Streamwise velocity distribution through the depth is also compared with some previous mathematical models. Researchers seeking the better control over the river morphology can apply this method without sacrificing much time and cost. This study is also included some insights to be pursued by future works.     

Physical modeling into outflow hydrographs and breach characteristics of homogeneous earthfill dams failure due to overtopping

The main objective of the present study is to introduce new empirical equations for the determination of breach geometrical dimensions and peak outflow discharge(Q_p).Therefore,a historic failure database of 109 embankments was collected and examined.The most important factors that affect the breach evolution,including grading size,hydraulic,and outflow characteristics are also studied.Some of the parameters used for the determination of Q_p and average breach width(Bave)have a significant effect on the erosion process,but they are less reflected in the technical literature.To study the behavior of noncohesive soils during overtopping,15 physical tests were performed at the laboratory,and the effects of interfering parameters were investigated.The experimental output hydrograph was used to simulate the hydrographs resulting from the failure of real dams,and recent artificial intelligence techniques along with linear and nonlinear regression models were employed.The area-time analysis of the laboratory hydrographs shows that the soil particle size and the characteristics of reservoir-basin significantly affect the rate of breach formation and outflow discharge.New relationships are introduced,based on the breach characteristics,by a combination of historical and experimental data,as well as case studies conducted on the hypothetical failure of 10 operational dams.The mathematical model is also used to simulate the process of breach evaluation.Based on statistical indices,comparison of the results,and sensitivity analysis,the developed equations can better express the susceptibility of materials to erosion and their application can minimize downstream vulnerabilities.     

Kerman Clay Improvement by Lime and Bentonite to Be Used as Materials of Landfill Liner

Kerman province, located in the south eastern Iran, is dominated with clays which can be used in different projects. The liner system within a landfill is constructed to control leachate migration and can be constructed by low permeable natural soils or plastic lining materials, environmentally however, natural materials is preferred that usually need to be amended in order to meet requirements recommended by environmental agencies. This research examines the possibility of using the Kerman collapsible clay as a liner layer material. A set of laboratory test was conducted on pure soil samples and additive treated samples. The moderate collapse potential of the used soil is decreased with wet compaction and under the effect of additive-soil reactions. Laboratory investigations showed that lime and bentonite treatment improved the hydraulic conductivity. The results revealed hydraulic conductivities on the order of 10^?8 m/s. The obtained values met the 1.0E?07 m/s criterion required by Iranian standards. Unconfined compression tests were also performed on pure soil and additive amended samples. The unconfined compression strength values demonstrated gradual decreases with the addition of bentonite and considerable increases with adding lime such that with adding 1% lime the unconfined compression strength increased by 75%. This study verified that the Kerman collapsing clay can be used as a liner material using lime and bentonite as additives.     

Titanium‐in‐biotite thermometry in porphyry copper systems: Challenges to application of the thermometer

Empirical geothermometer dealing with Ti solubility in the Fe‐Mg biotites was originally proposed for biotites in graphitic, peraluminous metapelites containing ilmenite or rutile that equilibrated roughly at 4–6 kbar. Given that biotites are abundant in the porphyry copper systems, this geothermometer has frequently been used for the determination of magmatic–hydrothermal temperatures in the porphyry copper systems. Common associations of porphyry copper deposits (PCDs), that is, low Al content of biotite, biotite chloritization (causes the biotite to become more magnesian and to lose Ti), and biotite formation by amphibole replacement, as well as disequilibrium, local equilibrium, or re‐equilibration of biotites, especially through potassic alteration, may provide significant uncertainty in the temperatures estimated a by Ti‐in‐biotite geothermometer. In addition, besides the calibration range of thermometer for pressure (400–600 MPa), the temperatures of major sulfide precipitation in PCDs (>~400°C) does not fit with the temperature range of thermometer calibration (480–800°C). Worth noting, as confirmed by fluid inclusion data in the Sarkuh PCD, regardless of presence of mineralogical requirements, obtained temperatures of sulfide mineralization using Ti in biotite thermometer could be overestimated. This may be due to the difference between general conditions of sulfide mineralization and calibration range of Ti in the biotite thermometer for pressure and temperature, as well as the metaluminous nature of biotites in PCDs.     

Effect of Microbial Siderophore DFOB on Pb, Zn, and Cd Sorption Onto Zeolite

Recent studies suggest that siderophores form stable complexes with divalent metals and affect their mobility. In this work, effects of trihydroxamate microbial siderophores and desferrioxamine-B (DFOB) on Pb(II), Zn(II), and Cd(II) sorption by two kinds of synthesized zeolites (13X and Na?CY) as a function of pH were investigated. Results showed that 13X zeolite has a higher sorption affinity for studied metals than Na?CY. DFOB strongly affected metal sorption on both zeolites. Under slightly acidic to neutral condition, DFOB increased the metal sorption on zeolites due to the sorption of positively charged heavy metal?CDFOB complexes. Whereas by increasing pH (>7), the mobilizing effect of DFOB was observed for Pb, Zn, and Cd. DFOB drastically decreased (80?%) Zn sorption in alkaline condition. As a result, siderophores can weaken the treatment efficiency of zeolites and increase the bioavailability of metals in soils. Surface complexation modeling revealed that the effects of DFOB on metal sorption by 13X and Na?CY zeolites can be explained by the differences in their surface charge. In general, the result shows the influence of DFOB on metal sorption by zeolites over the pH range 4?C9 and decreasing in the sequence Zn?>?Pb?>?Cd.     

Granite- and gabbrodiorite-associated skarn deposits of NW Iran

Field and laboratory studies show that there are two types of skarn deposits in NW Iran: granite-associated (type I) and gabbrodiorite-associated (type II). Granite-associated deposits are accompanied by Cu and Fe mineralisation, whereas Mn and Fe are the main ore metals in gabbrodiorite-associated skarn deposits. There are some differences in the mineralogy of these skarn deposits. Bixbyite, piemontite and Cr-bearing garnet are found only in gabbrodiorite-associated skarns, whereas idocrase occurs only in granite-associated deposits. Type II skarns show exoskarn features, whereas some type I skarns have developed endoskarn as well. Evidence of boiling of hydrothermal fluid can be seen in both types and seems to be a common mechanism of mineral deposition. Gabbrodiorite-associated skarns show higher fO₂ than granite-associated deposits. Based on mineralogical and textural evidence, mineralisation in both groups has started from about 550 °C. Early formed anhydrous minerals have begun to be replaced by hydrous minerals from about 400 °C.It seems that due to low fluid content in the gabbrodioritic magma, heated meteoritic water in the surrounding volcanoclastic and tuffaceous rocks was the main source of hydrothermal solution in the gabbrodiorite-associated skarn system.