Determination of phospholipid fatty acid structures and stable carbon isotope compositions of deep-sea sediments of the Northwest Pacific, ODP site 1179

Sediment samples ranging from 0.05 to 278 m below sea floor (mbsf) at a Northwest Pacific deep-water (5564 mbsl) site (ODP Leg 191, Site 1179) were analyzed for phospholipid fatty acids (PLFAs). Total PLFA concentrations decreased by a factor of three over the first meter of sediment and then decreased at a slower rate to approximately 30 mbsf. The sharp decrease over the first meter corresponds to the depth of nitrate and Mn(IV) reduction as indicated by pore water chemistry. PLFA-based cell numbers at site 1179 had a similar depth profile as that for Acridine orange direct cell counts previously made on ODP site 1149 sediments which have a similar water depth and lithology. The mole percentage of straight chain saturated PLFAs increases with depth, with a large shift between the 0.95 and 3.95 mbsf samples. PLFA stable carbon isotope ratios were determined for sediments from 0.05 to 4.53 mbsf and showed a general trend toward more depleted δ¹³C values with depth. Both of these observations may indicate a shift in the bacterial community with depth across the different redox zones inferred from pore water chemistry data. The PLFA 10me16:0, which has been attributed to the bacterial genera Desulfobacter in many marine sediments, showed the greatest isotopic depletion, decreasing from − 20 to − 35‰ over the first meter of sediment. Pore water chemistry suggested that sulfate reduction was absent or minimal over this same sediment interval. However, 10me16:0 has been shown to be produced by recently discovered anaerobic ammonium oxidizing (anammox) bacteria which are known chemoautotrophs. The increasing depletion in δ¹³C of 10me16:0 with the unusually lower concentration of ammonium and linear decrease of nitrate concentration is consistent with a scenario of anammox bacteria mediating the oxidation of ammonium via nitrite, an intermediate of nitrate reduction.     

δC of low-molecular-weight organic acids generated by the hydrous pyrolysis of oil-prone source rocks

Low-molecular-weight (LMW) aqueous organic acids were generated from six oil-prone source rocks under hydrous-pyrolysis conditions. Differences in total organic carbon-normalized acid generation are a function of the initial thermal maturity of the source rock and the oxygen content of the kerogen (OI). Carbon-isotope analyses were used to identify potential generation mechanisms and other chemical reactions that might influence the occurrence of LMW organic acids. The generated LMW acids display increasing ¹³C content as a function of decreasing molecular weight and increasing thermal maturity. The magnitudes of observed isotope fractionations are source-rock dependent. These data are consistent with δ¹³C values of organic acids presented in a field study of the San Joaquin Basin and likely reflect the contributions from alkyl-carbons and carboxyl-carbons with distinct δ¹³C values. The data do not support any particular organic acid generation mechanism. The isotopic trends observed as a function of molecular weight, thermal maturity, and rock type are not supported by either generation mechanisms or destructive decarboxylation. It is therefore proposed that organic acids experience isotopic fractionation during generation consistent with a primary kinetic isotope effect and subsequently undergo an exchange reaction between the carboxyl carbon and dissolved inorganic carbon that significantly influences the carbon isotope composition observed for the entire molecule. Although generation and decarboxylation may influence the δ¹³C values of organic acids, in the hydrous pyrolysis system described, the nondestructive, pH-dependent exchange of carboxyl carbon with inorganic carbon appears to be the most important reaction mechanism controlling the δ¹³C values of the organic acids.     

Long‐term monitoring of a mercury contaminated estuary (Ria de Aveiro,Portugal): the effect of weather events and management in mercury transport

The main aim of this research was to assess the mercury transport from an estuarine basin with a background of anthropogenic contamination during a spring tidal cycle (year 2009) and compare it with two previous tidal cycles (years 1994 and 1999), as part of a long‐term monitoring program. Results showed that effective mercury transport occurs both in the dissolved and particulate fractions (0.18 and 0.20 kg per tidal cycle, respectively), and despite an overall decrease in environmental contamination, results more than double previous findings on particulate transport in the system. These findings result essentially from changes in the tidal prism (net export of 2 million m³ of water), given that both dissolved and particulate concentrations did not increase over time. Hydrodynamic simulations were performed to evaluate the effect of physical disturbance (dredging) and weather events (increased freshwater flow) in these processes, and results suggest the increased freshwater flow into the system as the main forcing function for the mercury transport increment. These results highlight the importance of long‐term monitoring programs, since despite an overall improvement in local contamination levels, the enhancement of transport processes through hydrological changes increases environmental pressure away from the contamination source. Copyright © 2012 John Wiley & Sons, Ltd.     

A new numerical approach to the hyperstatic reaction method for segmental tunnel linings

This paper proposes a numerical approach to the hyperstatic reaction method (HRM) for the analysis of segmental tunnel linings. The influence of segmental joints has been considered directly using a fixity ratio that is determined on the basis of the rotational stiffness. The parameters necessary for the calculation are presented. A specific implementation has been developed using a FEM framework. This code is able to consider the three‐dimensional (3D) effect of segment joints in successive rings on the tunnel lining behaviour. The present HRM allows one to take an arbitrary distribution of segment joints along the tunnel boundary into consideration. In addition, the rotational stiffness of segment joints has been simulated using nonlinear behaviour, as it is closer to the true behaviour of a joint than linear or bilinear behaviour. The numerical results of three hypotheses on ring interaction, which allow the 3D effect of a segmental tunnel lining to be taken into account, have been compared with data obtained from the shield‐driven tunnel of the Bologna–Florence high‐speed railway line project. The numerical results presented in the paper show that the proposed HRM can be used to effectively estimate the behaviour of a segmental tunnel lining. Copyright © 2014 John Wiley & Sons, Ltd.     

The effect of pore water pressure on tunnel face stability

The kinematic approach in combination with numerical simulation is used to examine the effect of pore water pressure on tunnel face stability. Pore water pressure distribution obtained by numerical calculations using FLAC^3D is used to interpolate the pore water pressure on a 3D rotational collapse mechanism. Comparisons are made to check the present approach against other solutions, showing that the present approach improves the existing upper bound solutions. Results obtained indicate that critical effective face pressure increases with water table elevation. Several normalized charts are also presented for quick evaluation of tunnel face stability. At the end of the paper, the influence of anisotropic permeability on tunnel face stability is also discussed, showing that the isotropic model leads to an overestimation of the necessary tunnel face pressure for anisotropic soils. Copyright © 2016 John Wiley & Sons, Ltd.     

A model for adjustment of differential gravity measurements with simultaneous gravimeter calibration

 A mathematical model is proposed for adjustment of differential or relative gravity measurements, involving simultaneously instrumental readings, coefficients of the calibration function, and gravity values of selected base stations. Tests were performed with LaCoste and Romberg model G gravimeter measurements for a set of base stations located along a north–south line with 1750 mGal gravity range. This line was linked to nine control stations, where absolute gravity values had been determined by the free-fall method, with an accuracy better than 10 μGal. The model shows good consistence and stability. Results show the possibility of improving the calibration functions of gravimeters, as well as a better estimation of the gravity values, due to the flexibility admitted to the values of the calibration coefficients. Received: 15 November 1999 / Accepted: 31 October 2000     

Basalt magmatism along the passive continental margin of SE Brazil (Campos basin)

The SE-Brazil passive continental margin is characterized by tholeiitic magmatism that is particularly widespread in the marginal Campos basin, facing the inland flood basalts of the adjacent Paranà basin. Campos magmatism is represented by Early Cretaceous (EC; 134–122 Ma) flood basalts and minor Upper Cretaceous-Early Tertiary basalt flows and intrusives, which were emplaced in a basin with attenuated crustal thickness (20 km). Petrography, mineral chemistry, wholerock geochemistry and Sr–Nd isotope composition emphasize that the EC-Campos basalts have suffered extensive seawater interaction which caused enrichment in MgO, FeO total, K₂O, Rb and Ba, and depletion in SiO₂ and CaO, while Zr, Nb, Y and REE remained virtually constant in samples with loss-on-ignition values less than 4 wt%. In general, Campos basalts have bulkrock chemistry similar to those of the inland Parana tholeiites (140–130 Ma) with relatively low concentrations of incompatible elements and TiO₂ (<2 wt%). Batch-melting calculations suggest that Campos basalt genesis requires a garnet-peridotite source and variable degree of melting (9–25%) in order to explain the rare-earth-element (REE) patterns with chondrite normalised La/Yb_(N) ratio ranging from 0.9–1.0 to 4.4–7.1. The Sr–Nd isotopic data for the slightly altered Campos basalts, of both Early Cretaceous and Upper Cretaceous-Early Tertiary age, plot close to bulk earth, or in the enriched quadrant of the mantle array. Inter-element (La, Zr, Nb, Ba) ratios preclude for the Campos (and Paranà) basalt genesis any significant participation of N-type (Zr/Nb>16) MORB (mid-ocean-ridge basalt) mantle in simple binary mixing models. On the whole, the Early Cretaceous Campos basalts appear as an easterly, younger extension of the northern Paranà volcanism and probably erupted during early stages of the major riftingprocesses which caused continental thinning. It is notable that in the Campos marginal basin both the basalt magmatism contemporaneous with the continental break-up, as well as that which occurred after the S. America-Africa separation, appears substantially related to subcontinental lithosphere and a Dupal-like OIB (ocean-island basalt) (e.g. Tristan da Cunha) source components.     

The volcano of Capelinhos (Azores), the solar activity and the earth-tide

Bulletin of Volcanology - Correlations on the eruptive behaviour of the volcano of Capelinhos (Fayal island) in 1957–58, with (a) solar activity, and (b) earth-tide amplitudes, by way of a...