A numerical comparison of 2D resistivity imaging with 10 electrode arrays

Numerical simulations are used to compare the resolution and efficiency of 2D resistivity imaging surveys for 10 electrode arrays. The arrays analysed include pole‐pole (PP), pole‐dipole (PD), half‐Wenner (HW), Wenner‐α (WN), Schlumberger (SC), dipole‐dipole (DD), Wenner‐β (WB), γ‐array (GM), multiple or moving gradient array (GD) and midpoint‐potential‐referred measurement (MPR) arrays. Five synthetic geological models, simulating a buried channel, a narrow conductive dike, a narrow resistive dike, dipping blocks and covered waste ponds, were used to examine the surveying efficiency (anomaly effects, signal‐to‐noise ratios) and the imaging capabilities of these arrays. The responses to variations in the data density and noise sensitivities of these electrode configurations were also investigated using robust (L₁‐norm) inversion and smoothness‐constrained least‐squares (L₂‐norm) inversion for the five synthetic models. The results show the following. (i) GM and WN are less contaminated by noise than the other electrode arrays. (ii) The relative anomaly effects for the different arrays vary with the geological models. However, the relatively high anomaly effects of PP, GM and WB surveys do not always give a high‐resolution image. PD, DD and GD can yield better resolution images than GM, PP, WN and WB, although they are more susceptible to noise contamination. SC is also a strong candidate but is expected to give more edge effects. (iii) The imaging quality of these arrays is relatively robust with respect to reductions in the data density of a multi‐electrode layout within the tested ranges. (iv) The robust inversion generally gives better imaging results than the L₂‐norm inversion, especially with noisy data, except for the dipping block structure presented here. (v) GD and MPR are well suited to multichannel surveying and GD may produce images that are comparable to those obtained with DD and PD. Accordingly, the GD, PD, DD and SC arrays are strongly recommended for 2D resistivity imaging, where the final choice will be determined by the expected geology, the purpose of the survey and logistical considerations.     

Fouling assemblages on offshore wind power plants and adjacent substrata

A significant expansion of offshore wind power is expected in the near future, with thousands of turbines in coastal waters, and various aspects of how this may influence the coastal ecology including disturbance effects from noise, shadows, electromagnetic fields, and changed hydrological conditions are accordingly of concern. Further, wind power plants constitute habitats for a number of organisms, and may locally alter assemblage composition and biomass of invertebrates, algae and fish. In this study, fouling assemblages on offshore wind turbines were compared to adjacent hard substrate. Influences of the structures on the seabed were also investigated. The turbines differed significantly from adjacent boulders in terms of assemblage composition of epibiota and motile invertebrates. Species number and Shannon–Wiener diversity were, also, significantly lower on the wind power plants. It was also indicated that the turbines might have affected assemblages of invertebrates and algae on adjacent boulders. Off shore wind power plant offer atypical substrates for fouling assemblages in terms of orientation, depth range, structure, and surface texture. Some potential ecological implications of the addition of these non-natural habitats for coastal ecology are discussed.     

Resolution of 2D Wenner resistivity imaging as assessed by numerical modelling

Modelling of 2D resistivity imaging was done in order to understand the principle resolution of the technique in different geological situations, and for assessing the behaviour of the interpretation methods under controlled circumstances. The Wenner array was used throughout. The results show that the 1D approximation only provides reasonable results in environments with very gradual lateral resistivity changes, otherwise the result may be strongly misleading. Inversion using the 2D quasi-Newton technique results in adequate resolution of the structures in moderately complex environments, but the Gauss–Newton method holds a significant advantage in some complicated cases. The data density can also be of crucial importance for the resolution capability, notably of narrow structures.     

Comparison of geoelectrical imaging and tunnel documentation at the Hallandsås Tunnel, Sweden

For construction in rock a thorough pre-investigation is important in order to avoid unforeseen conditions which may delay the work. It is crucial to remember the results from this investigation in the further work, and use the experience from the construction to update the geological prognosis and reduce the uncertainties. Different geophysical methods have proved valuable tools in such investigations. In this work the electrical imaging is evaluated with regards to the method's applicability. The evaluation is done qualitatively by comparing the electrical imaging with tunnel documentation from a tunnel in Southern Sweden. By evaluating the result continuously when making the tunnel a more detailed geological prognosis can be compiled and used in the continued work with the tunnel. The parameters used for the comparison are lithology, Q, RQD, weathering and water leakage. The result was that virtually every change in electrical resistivity image coincides with a change in rock conditions. The general trend was that high resistivity corresponded with good quality gneiss whereas low resistivity corresponds to poor quality rock e.g., high weathering, low RQD, low Q and/or several lithological contacts. The intermediate resistivity is often amphibolites or rock with water bearing fractures. The results were supported by in-situ resistivity measurements inside the tunnel and resistivity logging in a core drilling. Geoelectrical imaging proved to give valuable information for a detailed geological model, which could be compiled for a section where the tunnel had not yet been drilled as a help for planning of the continued tunnel work. As is the case other geophysical methods it is clear that for the interpretation of data a priori information about the geological setting is necessary.     

Improving the groundwater-well siting approach in consolidated rock in Nampula Province,Mozambique

Vertical electrical sounding was used for assessing the suitability of the drill sites in crystalline areas within a water supply project in Nampula Province in Mozambique. Many boreholes have insufficient yield (<600 L/h). Electrical resistivity tomography (ERT) was carried out over seven boreholes with sufficient yield, and five boreholes with insufficient yield, in Rapale District, in an attempt to understand the reason for the failed boreholes. Two significant hydrogeological units were identified: the altered zone (19–220 ohm-m) with disintegrated rock fragments characterized by intermediate porosity and permeability, and the fractured zone (>420 ohm-m) with low porosity and high permeability. In addition to this, there is unfractured nonpermeable intact rock with resistivity of thousands of ohm-m. The unsuccessful boreholes were drilled over a highly resistive zone corresponding to fresh crystalline rock and a narrow altered layer with lower resistivity. Successful boreholes were drilled in places where the upper layers with lower resistivity correspond to a well-developed altered layer or a well-fractured basement. There are a few exceptions with boreholes drilled in seemingly favourable locations but they were nevertheless unsuccessful boreholes for unknown reasons. Furthermore, there were boreholes drilled into very resistive zones that produced successful water wells, which may be due to narrow permeable fracture zones that are not resolved by ERT. Community involvement is proposed, in choosing between alternative borehole locations based on information acquired with a scientifically based approach, including conceptual geological models and ERT. This approach could probably lower the borehole failure rate.     

Time-lapse resistivity investigations for imaging saltwater transport in glaciofluvial deposits

Five intersecting resistivity sections have been measured in glaciofluvial deposits hosting an aquifer of regional importance situated along a heavy traffic highway in Sweden. The winter salt spreading has caused a regular salinity increase through the years. For imaging the transport of saltwater in the aquifer, the sections were measured exactly in the same location before and after winter, and interpreted using a time-lapse inverse procedure. Some auger drilling and RCPT data were available for correlation. After winter, the resistivity had generally decreased under the water table and increased above it. The decrease in resistivity in the saturated zone is interpreted as a plume of more saline groundwater created by de-icing salt from the road. The increase in the upper layer can be explained by changes in temperature and soil moisture. The study shows that time-lapse resistivity investigations has potential for imaging hydraulic pathways in complex hydrogeological environments.     

Platforms in the akalche at E1 Mirador,Peten, Guatemala and their implications

Late Preclassic Period platforms were surveyed and test-excavated in a seasonal swamp or akalche, at the large ancient lowland Maya site of El Mirador in Peten, Guatemala. Pedological, hydrological, and archaeological evidence suggest that the climatic and hydrological regimes were drier than they are today to permit habitation and warrant the investment in labor. Nevertheless, observations of present conditions, including the clayey soils, indicate that the akalche was almost as inhospitable in antiquity as it is today, that it had the same extremely poor agricultural potentials and that intensive wetland cultivation would have necessitated sizeable investments in dams to dampen the extreme seasonal fluctuations in water levels. Dams are not observed, and evidence is elicited to indicate that they would be readily observable today had they been emplaced here in antiquity. We offer evidence suggesting that these platforms had domestic functions, but we are forced to conclude that intensive wetland cultivation did not sustain them nor this large regional center as a whole. We argue, instead, that these habitations constitute evidence for population pressures on urban upland resources, especially building sites and perhaps agricultural land. Akalche households appear to have sustained themselves, at least in part, by foraging for animal and plant foods, cordage products, building materials, and firewood. The data are inadequate to decide if these structures housed full or part time specialists, or if they were self-sufficient in subsistence. © 1994 John Wiley & Sons, Inc.     

Delimiting a saline water zone in Quaternary fluvial–alluvial deposits using transient electromagnetic: a case study in Punata,Bolivia

The semiarid Punata alluvial fan is located in the central part of Bolivia. The main activity of this region is the extensive agriculture, and groundwater is the main water supply. Local villagers who use groundwater reported that in some places groundwater has a salty taste. In order to investigate the origin of this problem, several TEM soundings were performed in the study area, and they were complemented with ERT surveys. The results show top layers with resistivity values ranging from 30 to 200 Ωm and a bottom layer with resistivity values ranging from 1 to 20 Ωm, which might be interpreted as the main aquifer and a layer with high clay content, respectively. Between the top and bottom layer, a transition zone with saline water has been identified, with resistivity values ranging from 0.1 to 1 Ωm. The origin of this closed-basin brine might be a product of the evaporation of paleolakes during the lower Pliocene, where saline clays were deposited. This study demonstrated the effectiveness of TEM sounding for mapping very low resistivity zones such as saline water.     

The relationship between regional stress field,fracture orientation and depth of weathering and implications for groundwater prospecting in crystalline rocks

In a uniform granite gneiss study area in central Zimbabwe, lineaments oriented parallel to the maximum regional compressive stress orientation exhibit the thickest regolith development, while lineaments oriented perpendicular to the maximum compressive stress show the shallowest development of weathered regolith. The principal fracture set orientations were mapped using aerial imagery. The regional stress field, estimated from global stress maps, was used to determine the stresses acting on each principal lineament orientation. Multi-electrode resistivity profiling was carried out across fractures with different orientations to determine their subsurface regolith conditions. The results indicate that the 360 and 060° lineaments, which are sub-parallel to the principal compressive stress orientation (σ₁) exhibit maximum development of the regolith, while 130° lineaments perpendicular to σ₁ do not exhibit significant regolith development. Since regolith thickness has been positively correlated with groundwater resources, it is suggested that fractures with orientations sub-parallel to the principal compressive stress direction constitute favourable groundwater targets. Knowledge of the regional stress field and fracture set orientations can be used as an effective low cost tool for locating potentially higher yielding boreholes in crystalline rock terrains.     

Hydrogeological and hydrochemical features of an area polluted by heavy metals in central Nicaragua

Geophysical and hydrochemical surveys were used to investigate the hydrogeological conditions in one of the Río Sucio microbasins, in central Nicaragua. Zones of vertical structures (i.e. fractures and quartz veins) and weathering were mapped using Continuous Vertical Electrical Soundings (CVES), as such zones are of major importance for groundwater transport. Water from the springs was analysed to determine concentrations of major ions and heavy metals. Low ion concentrations and ¹⁸O analyses indicate that the springs occur close to their recharge areas and there is a relatively rapid groundwater circulation. Mercury (Hg) content in the springs was low, while comparatively high amounts of lead (Pb) were found. The results presented here demonstrate the important function of weathering and tectonics in the occurrence of groundwater systems in the basin. Hg and Pb found in the springs’ water reveal the existence of an increase in pollution sources disseminating in the area. More than 100 years of using mercury in the gold-mining industry and releasing wastes into rivers has affected water quality and ecosystems. Further investigations are needed in this area to determine the groundwater vulnerability to this pollution as this resource may be needed in the future.