Groundwater sustainability and groundwater/surface-water interaction in arid Dunhuang Basin,northwest China

The Dunhuang Basin, a typical inland basin in northwestern China, suffers a net loss of groundwater and the occasional disappearance of the Crescent Lake. Within this region, the groundwater/surface-water interactions are important for the sustainability of the groundwater resources. A three-dimensional transient groundwater flow model was established and calibrated using MODFLOW 2000, which was used to predict changes to these interactions once a water diversion project is completed. The simulated results indicate that introducing water from outside of the basin into the Shule and Danghe rivers could reverse the negative groundwater balance in the Basin. River-water/groundwater interactions control the groundwater hydrology, where river leakage to the groundwater in the Basin will increase from 3,114?×?10⁴ m³/year in 2017 to 11,875?×?10⁴ m³/year in 2021, and to 17,039?×?10⁴ m³/year in 2036. In comparison, groundwater discharge to the rivers will decrease from 3277?×?10⁴ m³/year in 2017 to 1857?×?10⁴ m³/year in 2021, and to 510?×?10⁴ m³/year by 2036; thus, the hydrology will switch from groundwater discharge to groundwater recharge after implementing the water diversion project. The simulation indicates that the increased net river infiltration due to the water diversion project will raise the water table and then effectively increasing the water level of the Crescent Lake, as the lake level is contiguous with the water table. However, the regional phreatic evaporation will be enhanced, which may intensify soil salinization in the Dunhuang Basin. These results can guide the water allocation scheme for the water diversion project to alleviate groundwater depletion and mitigate geo-environmental problem.     

Numerical analysis of effect of baffle configuration on impact force exerted from rock avalanches

In mountainous areas, channelized rock avalanches swarm downslope leading to large impact forces on building structures in residential areas. Arrays of rock avalanche baffles are usually installed in front of rigid barriers to attenuate the flow energy of rock avalanches. However, previous studies have not sufficiently addressed the mechanisms of interaction between the rock avalanches and baffles. In addition, empirical design approaches such as debris flow (Tang et al., Quat Int 250:63–73, 2012), rockfall (Spang and Rautenstrauch, 1237–1243, 1988), snow avalanches (Favier et al., 14:3–15, 2012), and rock avalanches (Manzella and Labiouse, Landslides 10:23–36, 2013), which are applied in natural geo-disasters mitigation cannot met construction requirements. This study presents details of numerical modeling using the discrete element method (DEM) to investigate the effect of the configuration of baffles (number and spacing of baffle columns and rows) on the impact force that rock avalanches exert on baffles. The numerical modeling is firstly conducted to provide insights into the flow interaction between rock avalanches and an array of baffles. Then, a modeling analysis is made to investigate the change pattern of the impact force with respect to baffle configurations. The results demonstrate that three crucial influencing factors (baffle row numbers, baffle column spacing, and baffle row spacing) have close relationship with energy dissipation of baffles. Interestingly, it is found that capacity of energy dissipation of baffles increases with increasing baffle row numbers and baffle row spacing, while it decreases with increasing baffle column spacing. The results obtained from this study are useful for facilitating design of baffles against rock avalanches.     

Study on the deformation and failure modes of filling slope in loess filling engineering: a case study at a loess mountain airport

Lvliang airport is a typical loess filling engineering located in 20.5 km north of Lvliang City in Shanxi Province, China. By the end of March 2012, 14 fissures extending more than 7.5 m were observed in a loess-filled slope, of which the longest fissure is up to 82 m. Field monitoring and laboratory tests have been performed to investigate the slope failure modes. The test program includes wetting tests on unsaturated compacted samples and stress path tests on saturated samples. Field monitoring and observations show that differential settlement caused by non-homogeneity in compacted loess density might lead to the formation of fissures in the loess-filled slope. It was founded that the wetting deformation contributed to the development of differential settlement. Fissures are the essential factor for the loess-filled slope failure. Four deformation stages exhibit in the loess-filled slope prior final failure including development of the fissures, softening of the compacted loess, creeping of the slope leading edge and fissuring of the trailing edge and formation of the through-sliding surface. Development of the sliding surface mainly includes upward and downward expansion of the fissures. Upward expansion is a wetting failure process in loading condition, while downward expansion is a load-off wetting process. In addition, development of the sliding surface is accelerated by softening of the compacted soils as a result of water infiltration. Therefore, the key for taking countermeasures against filling landslides is to monitor and control the development of differential settlement and fissures in the slope shoulders. Digging out and extra-filling the fissures are an effective way for preventing these landslides.     

Effects of mechanical layering on hydraulic fracturing in shale gas reservoirs based on numerical models

Generally, induced hydraulic fractures are generated by fluid overpressure and are used to increase reservoir permeability through forming interconnected fracture systems. However, in heterogeneous and anisotropic rocks, many hydraulic fractures may become arrested or offset at layer contacts under certain conditions and do not form vertically connected fracture networks. Mechanical layering is an important factor causing anisotropy in sedimentary layers. Hence, in this study, with a shale gas reservoir case study in the Longmaxi Formation in the southeastern Chongqing region, Sichuan Basin, we present results from several numerical models to gain quantitative insights into the effects of mechanical layering on hydraulic fracturing. Results showed that the fractured area caused by hydraulic fracturing indicated a linear relationship with the neighboring layer’s Young’s modulus. An increase of the neighboring layer’s Young’s modulus resulted in better hydraulic fracturing effects. In addition, the contact between two neighboring layers is regarded as a zone with thickness and mechanical properties, which also influences the effects of hydraulic fracturing in reservoirs. The initial hydraulic fracture was unable to propagate into neighboring layers under a relatively low contact’s Young’s modulus. When associated local tensile stresses exceeded the rock strength, hydraulic fractures propagated into neighboring layers. Moreover, with the contact’s Young’s modulus becoming higher, the fractured area increased rapidly first, then slowly and finally became stable.     

闽赣交界武夷山南段“桃溪穹隆”形变特征及构造演化探讨

"桃溪穹隆"由内核、中间层和盖层组成,发育岩石流变,韧性、韧脆性和脆性变形(断裂)。文章以"桃溪穹隆"内核、中间层和盖层为对象,通过研究其形变特征、运动形式及相互关系,探讨穹隆上隆的运动方式,结合沉积事件、岩浆活动和构造运动,阐述穹隆的形成机制和构造演化特征。"桃溪穹隆"于加里东期(志留纪末)隆升,华力西期—印支期(晚二叠世—中三叠世)大规模上隆,燕山期及后期继承性活动,主隆升期(华力西期—印支期)为逆时针旋转上隆。穹隆长期隆升是该区古元古代结晶基底出露的主要原因。     

A study of the factors influencing the occurrence of landslides in the Wushan area

Due to the complex natural geological conditions, many slope-related geological hazards occur in the Three Gorges Reservoir area in China. This study focuses on the characteristics of landslide development and their underlying mechanisms in this area. A statistical analysis is conducted to determine the characteristics of landslide development in the Wushan area, including the landslide distribution as a function of the elevation, slope, landslide material composition, scale, lithology, boundary conditions, instability mechanism, stratigraphic age, attitude, and sliding direction. The mechanisms of slope instability and the effect on the occurrence of landslides are analyzed. This study provides important reference material for landslide research in the Three Gorges Reservoir area and similar stratigraphic areas.     

Synthesis and characterisation of a multifunctional oil-based drilling fluid additive

An oil-based drilling fluid additive H-DEA (or humic acid-cocamide diethanolamine) was synthesised using humic acid and cocamide diethanolamine as raw materials. The rheological behaviors of H-DEA showed that the synthesised product has the good properties in both decreasing the filtrate loss and improving rheology property of oil-based drilling fluids compared with other commercially available additives. Under the optimal additive amount of 3%, both API filtrate loss and yield point changed remarkably from 5.40 to 0.41 mL and 9.0 to 25.6 Pa, respectively. Furthermore, differential scanning calorimetry (DSC) showed that H-DEA has good thermal stability in a wide temperature range up to 170 °C. Infrared spectroscopy (IR) and rheological analysis revealed that the possible mechanism of the multifunctional effects may be attributed to the existing of high density of strong polar groups, hydrogen bonds, electrostatic forces, and intermolecular association on H-DEA molecular structure. The results of the study showed that the synthesised H-DEA can be potentially used as a multifunctional oil-based drilling fluid additive in oil-drilling excavation.