The radio luminosity function and the luminosity diameter function of extragalactic radio sources

On the basis of a radio index-surface brightness diagram recently published, the luminosity function and the luminosity diameter function are obtained. The uncertainties due to the incompleteness of the sample are of the same order as the statistical uncertainties. The luminosity function differs considerably from a simple power law and supports the distinction of two populations. The density of the weak population (P<10³⁵ W Hz⁻¹ ster⁻¹ at 1400 MHz) follows nearly a power law in P and increases towards small diameters at least down to I kpc. The density of the strong population (the high luminosity and small diameter part of which is occupied by the quasars) has a maximum between 10²⁵ and 10²⁸ W Hz⁻¹ ster⁻¹ and around 100 kpc. A strong evolution effect is clearly present and is in a good agreement with the models obtained from the log N-log S counts.     

Extraction and recovery of precious metals from electronic waste printed circuit boards by bioleaching acidophilic fungi

Printed circuit boards contain precious metals. They are produced in large volumes, rendering them an important component of the electronic waste. In view of the heterogeneity of the metals present, reprocessing of electronic waste is a heinous task. The present study focused on leaching of valuable metals from electronic waste printed circuit boards using Aspergillus niger DDNS1. The adaptation phases began at 0.1, 0.5 and 1.0% of fine powder of printed circuit boards with 10% inoculum and were optimized with three effective factors, viz. initial pH, particle size and pulp density, to achieve the maximum simultaneous recovery of the valuable metals. The interactions of these metals were also deciphered using scanning electron microscopy, energy-dispersive X-ray spectroscopy, X-ray diffraction, Fourier transform infrared spectrum and atomic absorption spectroscopy. The results indicated that extraction of the precious metals was accomplished mainly through the unique organic acids originating from A. niger DDNS1. The initial pH played an important role in the extraction of the precious metals and the metals precipitate formation. The leaching rate of the metals was generally higher at low powder dosage of printed circuit boards. The toxicity of the printed circuit boards had little effect on two-step bioleaching at the pulp density of 0.1% compared to one-step bioleaching. The two-step bioleaching process was followed under organic acid-forming conditions for the maximum mobilization of metals. Thus, the precious metals from printed circuit boards could be mobilized through fungal bioleaching which promises an important industrial application in recycling of electronic wastes.     

Snow measurement techniques for land-surface-atmosphere exchange studies in boreal landscapes

Summary  Snow has been studied widely in hydrology for many decades whereas recent meteorological interest in snow is caused by increased emphasis on high latitudes and wintertime in climate-change research as well as by the need to improve weather-forecast models during these conditions. Ground-based measurements of snow properties are needed both to improve understanding of surface-atmosphere exchange processes and to provide ground truth to new remote-sensing algorithms. This justifies a review of techniques to measure snow in combination with establishment of criteria for the suitability of the methods for process studies. This review assesses the state-of-art in ground-based snow-measurement techniques in the end of the 1990s in view of their accuracy, time resolution, possibility to automate, practicality and suitability in different terrain. Methods for snow-pack water equivalent, depth, density, growth, quality, liquid-water content and water leaving the snow pack are reviewed. Synoptic snow measurements in Fennoscandian countries are widely varying and there is no single standard on which process-related studies can build. A long-term, continuous monitoring of mass and energy properties of a snow cover requires a combination of point-measurement techniques. Areally representative values of snow properties can be achieved through a combination of automatically collected point data with repeated manual, areally covering measurements, remote-sensing data and digital elevation models, preferably in a GIS framework. Received August 27, 1999     

Improved Petrological Modal Analyses from X-ray Powder Diffraction Data by use of the Rietveld Method I. Selected Igneous, Volcanic, and Metamorphic Rocks

Mineral modes have been determined for specimens of eight rocktypes from CuK X-ray powder diffraction data using the Rietveldmethod. The samples include two granites, a granodiorite, adamellite,gabbro, basalt, trachyte, and two granulite-facies metamorphicrocks. Up to eight individual mineral components have been measuredin each sample (no glassy phases were observed), with a detectionlimit of {small tilde}1 wt.%, depending on the mineral assemblage.Marked variations in grain size (i.e., granite vs. trachyte)provide no difficulties for the X-ray method. The X-ray resultscompare very favourably with (1) optical modes determined forthe medium–coarse-grained samples by point counting, (2)normative calculations obtained using locally enhanced catanormand mesonorm software, and (3) corresponding Rietveld modesdetermined, for two samples, from neutron powder data. Wheredifferences occur, these are discussed in relation to the limitationsof each of the methods. The improved accuracy of the X-ray method is due primarily tothe incorporation of the full diffraction profile in the Rietveldanalysis calculations, and the elimination of preferred orientationby collecting the data from samples packed in glass capillaries(i.e., Debye–Scherrer mode). The good agreement of theX-ray and neutron modes shows that the usual problems encounteredwith microabsorption, extinction, and sampling are of littleconcern in these rocks. The results highlight one of the majoradvantages provided by Rietveld modal analysis over the moretraditional ‘reference intensity’ X-ray methods,namely, that the crystal chemistry (and thus the calibrationconstants) of the individual phases can be adjusted dynamicallyduring each individual analysis. This not only provides moreaccurate phase abundances, but also gives important supplementaryinformation about the mineralogy of the major components.     

A case study of warm air advection over a melting snow surface

When relatively warm, moist air moves over a snow surface, sensible heat and moisture are extracted from its lower layers and used to melt the snow. The depth of the cooled layer depends on horizontal wind speeds and the presence of high vertical wind shear. The mechanism for air mass modification appears to be turbulent mixing.     

Risk Assessment and Disaster Management for Natural and Anthropogenically Induced Geologic Hazards: Application to the Preolkhon Region,Western Lake Baikal,Siberia, Russia

In the Western Lake Baikal, recent Baikal Rift's tectonics control the topography, seismicity, climate, geomorphology, and economy. Scarps, facets, structural terraces, horsts and grabens, and trapezoid valleys can be clearly observed. They have been generated by the recent tectonic movements along the faults and represent a serious geologic hazard. The specific geological conditions predetermine a unique variety of landscapes. Thus, the main type of the economy is tourism. However, unorganized tourism leads to the degradation of the unique landscapes. It increases risk and requires disaster management. Three criteria has been used for risk assessment: (1) degree of geologic hazard; (2) degree of landscape degradation; and (3) degree of the economy's vitality. The high ecological significance and low stability to antropogeneous pressure are typical for landscapes of the Western Lake Baikal. Thus, some special activities of disaster management should be implemented based on our investigation.     

A 2D finite volume model for bebris flow and its application to events occurred in the Eastern Pyrenees

FLATModel is a 2D finite volume code that contains several original approaches to improve debris-flow simulation. Firstly, FLATModel incorporates a ＂stop-and-go＂ technique in each cell to allow continuous collapses and remobilizations of the debris-flow mass. Secondly, flow velocity and consequently yield stress is directly associated with the type of rheology to improve boundary accuracy. Thirdly, a simple approach for entrainment is also included in the model to analyse the effect of basal erosion of debris flows. FLATMODEL was tested at several events that occurred in the Eastern Pyrenees and simulation results indicated that the model can represent rather well the different characteristics observed in the field.     

Investigation of submicron volcanic aerosol-particles by photoelectron emission

Volcanic aerosol emissions have been studied for the first time by in situ photoelectric charging. Explorative studies on Mt Etna reveal large concentrations of particles below 1000 nm with the spectrum peaking in the size range of 100–1000 nm diameter. Although a large fraction of the particles is already charged upon emission, the net electrical charge carried by the aerosol turned out to be close to zero.Particles with high photoelectric yield vary greatly in their relative abundance and seem to occur mainly at active points of the volcano.     

Use of Rhodamine water tracer in the marshland upwelling system

Rhodamine water tracer (RWT) was used to characterize the migration of waste water within the saline subsurface of a marshland upwelling system (MUS), which is an alternative on-site waste water treatment system for coastal areas. Field tracer studies were performed to investigate the fresh waste water plume movement within the saline ground water. Pore velocities were calculated using first detection times and ranged from 0.68 to 10.7 x 10(-4) cm/sec for the loamy sandy soil matrix present at the site. Use of RWT in the field also allowed determination of main and preferential flowpaths. One- and two-dimensional laboratory experiments were performed using silica sand to investigate the interactions of the organically rich waste water with RWT within the zone surrounding the point of injection (one-dimensional) and the impact of background salinity on plume movement (two-dimensional). The results from these studies were used to help explain the field data. One-dimensional breakthrough curves revealed retardation factors for the RWT in the waste water mixture of 1.73 to 1.90. These results were similar to other researchers, indicating little interaction between the waste water and RWT. Variations in pore water salinity (5, 15, 25, and 35 ppt) were found to have a significant effect on pore water velocities of the fresh water plume (two-dimensional), indicating the need to incorporate background salinities into the design process for MUS.