清代地理学家魏源及其《海国图志》──纪念魏源诞生200周年

本文阐述我国清代中期思想家、地理学家魏源的思想及共《海国图志》的特点及历史意义。     

Structural similarity and variety at the tips in a wide range of strike–slip faults: a review

Strike–slip faults are often accompanied by a variety of structures, particularly at their tips. The zones of additional fracturing are classified as tip‐damage zones. These zones can be subdivided into several different damage patterns based on the nature and orientation of faults and fractures developed. Damage zones at the ends of small strike–slip faults (mode II tips) develop wing cracks, horsetail splays, antithetic faults, synthetic branch faults and solution surfaces. Similar tip‐damage patterns are also commonly observed at larger (regional) scales, but with a dominance of faulting over tensile cracks and solution surfaces. Wing cracks and horsetail splays developed at small‐scale faults are replaced by normal faults in large‐scale faults. Antithetic faults and synthetic branch faults are observed at small and large scales. Thrust faults are developed at large scales, in a similar pattern to solution surfaces at a small scale. All these structures may show slightly different angular relationships to the master fault at small and large scale, but develop in response similar stress distribution and mechanics around the fault. Thus, mode II tip‐damage zones show similar patterns over a wide range of fault scales.     

Food Deserts in the Prairies? Supermarket Accessibility and Neighborhood Need in Edmonton,Canada*

The U.S. and U.K. literatures have discussed “food deserts,” reflecting populated, typically urban, low‐income areas with limited access to full‐service supermarkets. Less is known about supermarket accessibility within Canadian cities. This article uses the minimum distance and coverage methods to determine supermarket accessibility within the city of Edmonton, Canada, with a focus on high‐need and inner‐city neighborhoods. The results show that for 1999 both of these areas generally had higher accessibility than the remainder of the city, but six high‐need neighborhoods had poor supermarket accessibility. We conclude by examining potential reasons for differences in supermarket accessibility between Canadian, U.S., and U.K. cities.     

南极三块（L3）陨石球粒结构类型及其矿物学物征

我国第16次南极考察队回收到6块稀少种类陨石-L3型,GRV99001,GRV99019,GRV99020,GRV99021, GRV99022,GRV99026。本文对其中3块陨石进行研究,研究它们的球粒结构和矿物化学成分．它们虽然都属于非平衡普通球粒陨石(L3),但它们的亚类不同,GRV 99001为L3．4,GRV99026为L3．5,GRV99019为L3．6．它们的球粒结构和球粒内的矿物晶体完整性和矿物组合变化比较大,橄榄石和辉石以高镁为特征．这三块陨石的球粒结构种类比较多,有班状的、炉条状的、扇形的和隐晶质的等．在GRV99001陨石中班状结构的球粒内能见到一个或两个以上完整的单晶橄榄石构成的球粒,也能见到多个细小的或是破碎橄榄石,被包裹在辉石晶体内．而在GRV99019和GRV99026陨石中只能见到多个细小单晶体或是破碎的橄榄石晶体．GRV99001陨石的炉条状结构,好象是由一条带状长石矿物,穿插在单个橄榄石晶体中构成．扇形和伞形结构的球粒,以一个点为中心,向外放射呈扇形．如GRV99019陨石中扇形结构球粒,它们是以辉石为主,陨硫铁充填在低钙辉石缝隙中,形成扇形．另一种是以多个点为中心,如GRV99001陨石,它们是由橄榄石、低钙辉石和长石质的玻璃,构成多个小伞形,形状类似三维立体的球,裂缝中也充填有金属矿物．隐晶质的球粒在GRV99026陨石中有两种,一种是在一厘米等于 100un时呈现隐晶质矿物,而放大到一厘米等于5un时,就可以清楚看到两种低钙辉石矿物,在低钙辉石中还有金属矿物．另一种隐晶质结构球粒由极细小破碎的橄榄石和辉石矿物构成．这三块陨石中的橄榄石和辉石都以高镁为特征．班状结构球粒,在GRV99001陨石中橄榄石的MgO-33．37-51．21,辉石为35．9-36．61;GRV99019陨石中橄榄石23．33-56．58,辉石 21．38-33．07;GRV99026陨石中橄榄石45．91-52．63,辉石34．48-37．35．扇形结构球粒,在GRV99001陨石中橄榄石29．94 -46．22,辉石28．17-30．36;GRV99019陨石中橄榄石29．17-34．38,辉石23．11-27．79．炉条状结构的球粒,在GRV99001 陨石中橄榄石51．84-56．03．隐晶质结构球粒,在GRV99026陨石中辉石20．17-21．54,橄榄石30．84-32．66．由此看出矿物晶体完整性越好镁的含量越高．     

Structural damage detection using the optimal weights of the approximating artificial neural networks

This work presents a novel neural network‐based approach to detect structural damage. The proposed approach comprises two steps. The first step, system identification, involves using neural system identification networks (NSINs) to identify the undamaged and damaged states of a structural system. The partial derivatives of the outputs with respect to the inputs of the NSIN, which identifies the system in a certain undamaged or damaged state, have a negligible variation with different system errors. This loosely defined unique property enables these partial derivatives to quantitatively indicate system damage from the model parameters. The second step, structural damage detection, involves using the neural damage detection network (NDDN) to detect the location and extent of the structural damage. The input to the NDDN is taken as the aforementioned partial derivatives of NSIN, and the output of the NDDN identifies the damage level for each member in the structure. Moreover, SDOF and MDOF examples are presented to demonstrate the feasibility of using the proposed method for damage detection of linear structures. Copyright © 2001 John Wiley & Sons, Ltd.     

A mathematical hysteretic model for elastomeric isolation bearings

An analytical model for high damping elastomeric isolation bearings is presented in this paper. The model is used to describe mathematically the damping force and restoring force of the rubber material and bearing. Ten parameters to be identified from cyclic loading tests are included in the model. The sensitivity of the ten parameters in affecting the model is examined. These ten parameters are functions of a number of influence factors on the elastomer such as the rubber compound, Mullins effect, scragging effect, frequency, temperature and axial load. In this study, however, only the Mullins effect, scragging effect, frequency and temperature are investigated. Both material tests and shaking table tests were performed to validate the proposed model. Based on the comparison between the experimental and the analytical results, it is found that the proposed analytical model is capable of predicting the shear force–displacement hysteresis very accurately for both rubber material and bearing under cyclic loading reversals. The seismic response time histories of the bearing can also be captured, using the proposed analytical model, with a practically acceptable precision. Copyright © 2002 John Wiley & Sons, Ltd.     

Tests on low‐ductility RC frames under high‐ and low‐frequency excitations

The response of low‐ductility reinforced concrete (RC) frames, designed typically for a non‐seismic region, subjected to two frequencies of base excitations is studied. Five half‐scaled, two‐bay, two‐storey, RC frames, each approximately 5 m wide by 3.3 m high, were subjected to both horizontal and/or vertical base excitations with a frequency of 40 Hz as well as a lower frequency of about 4 Hz (close to the fundamental frequency) using a shake table. The imposed acceleration amplitude ranged from 0.2 to 1.2g. The test results showed that the response characteristics of the structures differed under high‐ and low‐frequency excitations. The frames were able to sustain high‐frequency excitations without damage but were inadequate for low‐frequency excitations, even though the frames exhibited some ductility. Linear‐elastic time‐history analysis can predict reasonably well the structural response under high‐frequency excitations. As the frames were not designed for seismic loads, the reinforcement detailing may not have been adequate, based on the crack pattern observed. The effect of vertical excitation can cause significant additional forces in the columns and moment reversals in the beams. The ‘strong‐column, weak‐beam’ approach for lateral load RC frame design is supported by experimental observations. Copyright © 2001 John Wiley & Sons, Ltd.     

Optimal design of passive energy dissipation systems based on H∞ and H2 performances

Passive energy dissipation devices (EDDs), such as viscous dampers, viscoelastic dampers, etc., have been used to effectively reduce the dynamic response of civil infrastructures, such as buildings and bridges, subject to earthquakes and strong winds. The design of these passive energy dissipation devices (EDDs) involves the determination of the optimal locations and the corresponding capacities. In this paper, we present two optimal design methodologies for passive EDDs based on active control theories, including H_∞ and H₂ performances, respectively. The optimal design methodologies presented are capable of determining the optimal locations and the corresponding capacities of EDDs. Emphasis is placed on the application of linear matrix inequality (LMI) for the effective design of passive EDDs using the popular MATLAB toolboxes. One important advantage of the proposed approaches is that the computation of the structural response is not needed in the design process. The proposed optimal design methodologies have been applied to: (i) a 10‐storey building and a 24‐storey building both subject to earthquake excitations, and (ii) a 76‐storey wind‐excited benchmark building, to demonstrate the advantages of the proposed design methodologies over the conventional equal capacity design. Copyright © 2002 John Wiley & Sons, Ltd.     

Study on effects of damping in laminated rubber bearings on seismic responses for a ⅛ scale isolated test structure

The effects of damping in various laminated rubber bearings (LRB) on the seismic response of a ?‐scale isolated test structure are investigated by shaking table tests and seismic response analyses. A series of shaking table tests of the structure were performed for a fixed base design and for a base isolation design. Two different types of LRB were used: natural rubber bearings (NRB) and lead rubber bearings (LLRB). Three different designs for the LLRB were tested; each design had a different diameter of lead plug, and thus, different damping values. Artificial time histories of peak ground acceleration 0.4g were used in both the tests and the analyses. In both shaking table tests and analyses, as expected, the acceleration responses of the seismically isolated test structure were considerably reduced. However, the shear displacement at the isolators was increased. To reduce the shear displacement in the isolators, the diameter of the lead plug in the LLRB had to be enlarged to increase isolator damping by more than 24%. This caused the isolator stiffness to increase, and resulted in amplifying the floor acceleration response spectra of the isolated test structure in the higher frequency ranges with a monotonic reduction of isolator shear displacement. Copyright © 2002 John Wiley & Sons, Ltd.     

Use of Chemotaxonomy To Study the Influence of Benzalkonium Chloride on Bacterial Populations in Biodegradation Testing

Contradictory results are reported for the behaviour of quaternary ammonium compounds (QACs) in sewage treatment plants (STPs). QACs may sorb onto activated sludge. Only little information is available with respect to effects of QACs against bacteria in STPs. Only 5 to 15 % of bacteria present in sewage sludge can be detected by means of culture dependent microbiological methods. The shift of the bacterial populations due to effects of test compounds have not been studied up to now with culture independent methods. The microbial populations shift was studied in situ using culture independent chemotaxonomy profiling ubiquinones and polyamines. Additionally, toxic effects of QACs against bacteria present in the test vessels of the Zahn‐Wellens test (OECD 302 B) were assessed with a toxicity control in the test. The ubiquinone profiles representing changes in Gram‐negative populations mainly showed that the activated sludge was affected only in test vessels containing benzalkonium chloride. According to chemotaxonomy Acinetobacter or/and some members of Pseudomonas spp. have been selected by benzalkonium chloride after some adaptation period (8 to 12 days).