In situ tensile fracture toughness of surficial cohesive marine sediments

This study reports the first in situ measurements of tensile fracture toughness, K _IC, of soft, surficial, cohesive marine sediments. A newly developed probe continuously measures the stress required to cause tensile failure in sediments to depths of up to 1 m. Probe measurements are in agreement with standard laboratory methods of K _IC measurements in both potter’s clay and natural sediments. The data comprise in situ depth profiles from three field sites in Nova Scotia, Canada. Measured K _IC at two muddy sites (median grain size of 23–50 μm) range from near zero at the sediment surface to >1,800 Pa m^1/2 at 0.2 m depth. These profiles also appear to identify the bioturbated/mixed depth. K _IC for a sandy site (>90% sand) is an order of magnitude lower than for the muddy sediments, and reflects the lack of cohesion/adhesion. A comparison of K _IC, median grain size, and porosity in muddy sediments indicates that consolidation increases fracture strength, whereas inclusion of sand causes weakening; thus, sand-bearing layers can be easily identified in K _IC profiles. K _IC and vane-measured shear strength correlate strongly, which suggests that the vane measurements should perhaps be interpreted as shear fracture toughness, rather than shear strength. Comparison of in situ probe-measured values with K _IC of soils and gelatin shows that sediments have a K _IC range intermediate between denser compacted soils and softer, elastic gelatin.     

DNAPL Characterization Methods and Approaches, Part 2: Cost Comparisons

Contamination from the use of chlorinated solvents, often classified as dense nonaqueous phase liquids (DNAPLs) when in an undissolved state, pose environmental threats to ground water resources worldwide. DNAPL site characterization method performance comparisons are presented in a companion paper (Kram et al. 2001). This study compares the costs for implementing various characterization approaches using synthetic unit model scenarios (UMSs), each with particular physical characteristics. Unit costs and assumptions related to labor, equipment, and consumables are applied to determine costs associated with each approach for various UMSs. In general, the direct-push sensor systems provide cost-effective characterization information in soils that are penetrable with relatively shallow (less than 10 to 15 m) water tables. For sites with impenetrable lithology using direct-push techniques, the Ribbon NAPL Sampler Flexible Liner Underground Technologies Everting (FLUTe) membrane appears to be the most cost-effective approach. For all scenarios studied, partitioning interwell tracer tests (PITTs) are the most expensive approach due to the extensive pre-and post-PITT requirements. However, the PITT is capable of providing useful additional information, such as approximate DNAPL saturation, which is not generally available from any of the other approaches included in this comparison.     

ITERA: IDL tool for emission-line ratio analysis

We present a new software tool to enable astronomers to easily compare observations of emission-line ratios with those determined by photoionization and shock models, ITERA, the IDL Tool for Emission-line Ratio Analysis. This tool can plot ratios of emission lines predicted by models and allows for comparison of observed line ratios against grids of these models selected from model libraries associated with the tool. We provide details of the libraries of standard photoionization and shock models available with ITERA, and, in addition, present three example emission-line ratio diagrams covering a range of wavelengths to demonstrate the capabilities of ITERA. ITERA, and associated libraries, is available from http://www.brentgroves.net/itera.html.     

The Kellwasser events in the Upper Devonian Frasnian to Famennian transition in the Toc Tat Formation,northern Vietnam

Upper Devonian carbonates of the Toc Tat Formation in the Si Phai Pass area of Dong Van District, northern Vietnam were deposited in carbonate platform, slope, and basin environments. These carbonates yield abundant conodonts indicative of the Palmatolepis nasuta, Pa. linguiformis and Pa. triangularis zones, the Frasnian–Famennian stage boundary being identified by the first occurrence of Pa. triangularis. Two positive carbon isotope excursions are recognized, the lower excursion peaking in the interval of the lower to middle Pa. nasuta Zone, whilst the upper excursion peaks just above the local Frasnian–Famennian boundary. Based on the biostratigraphy, these excursions equate to the Lower and Upper Kellwasser events. Locally, tentaculitoid taxa (Nowakia, Styliolina, Homoctenus, and Metastyliolina?) are abundant in the interval of the Pa. nasuta Zone, but show a drastic decline in abundance before the Lower Kellwasser Event, and only two taxa survived into the Famennian.     

深海滑坡灾害的物质点法模拟

深海滑坡可以沿着斜坡搬运大量沉积物,是危害巨大的海洋地质灾害之一。评估深海滑坡的流滑机制并量化分析其对海底结构物的冲击对海洋资源的开发利用至关重要。采用物质点法对滑坡的滑动特性进行了总应力分析。设计了三组不同的土体、海床参数,展现了三种不同的滑动形态:延展、块体和扩张。随后复现了流滑体对部分暴露管线的冲击过程,并对冲击力的稳定值进行了分析,分析中考虑了流滑体的惯性、抗剪强度和静压力的影响。研究表明,物质点法能够用于模拟深海滑坡的流滑过程及其对海底结构物的冲击,可以为海洋工程中的实际设计工作提供服务。     

Disseminated ‘jigsaw piece’ dolomite in Upper Jurassic shelf sandstones,Central North Sea: an example of cement growth during bioturbation?

Unusual textural and chemical characteristics of disseminated dolomite in Upper Jurassic shelf sediments of the North Sea have provided the basis for a proposed new interpretation of early diagenetic dolomite authigenesis in highly bioturbated marine sandstones. The dolomite is present throughout the Franklin Sandstone Formation of the Franklin and Elgin Fields as discrete, non‐ferroan, generally unzoned, subhedral to highly anhedral ‘jigsaw piece’ crystals. These are of a similar size to the detrital silicate grains and typically account for ≈5% of the rock volume. The dolomite crystals are never seen to form polycrystalline aggregates or concretions, or ever to envelop the adjacent silicate grains. They are uniformly dispersed throughout the sandstones, irrespective of detrital grain size or clay content. Dolomite authigenesis predated all the other significant diagenetic events visible in thin section. The dolomite is overgrown by late diagenetic ankerite, and bulk samples display stable isotope compositions that lie on a mixing trend between these components. Extrapolation of this trend suggests that the dolomite has near‐marine δ¹⁸O values and low, positive δ¹³C values. The unusual textural and chemical characteristics of this dolomite can all be reconciled if it formed in the near‐surface zone of active bioturbation. Sea water provided a plentiful reservoir of Mg and a pore fluid of regionally consistent δ¹⁸O. Labile bioclastic debris (e.g. aragonite, Mg‐calcite) supplied isotopically positive carbon to the pore fluids during shallow‐burial dissolution. Such dissolution took place in response to the ambient ‘calcite sea’ conditions, but may have been catalysed by organic matter oxidation reactions. Bioturbation not only ensured that the dissolving carbonate was dispersed throughout the sandstones, but also prohibited coalescence of the dolomite crystals and consequent cementation of the grain framework. Continued exchange of Mg²⁺ and Ca²⁺ with the sea‐water reservoir maintained a sufficient Mg/Ca ratio for dolomite (rather than calcite) to form. Irregular crystal shapes resulted from dissolution, of both the dolomite and the enclosed fine calcitic shell debris, before ankerite precipitation during deep‐burial diagenesis.     

Spherically symmetric cosmological perturbations in the de Donder gauge

Cosmological perturbations on a F-R-W background are considered in a modified de Donder gauge. To guarantee the energy-momentum conservation for the perturbations in the de Donder gauge a compatibility condition is obtained. Finally we present the basic equations for the propagation of spherically symmetric perturbations. These equations are the basis for investigating the influence of cosmological epoches on the growing of density contrasts.     

Marine birds breeding in Penny Strait and Queens Channel, Nunavut, Canada

Surveys of breeding birds on small islands in Penny Strait and Queens Channel, Nunavut Territory, Canada, were conducted in July 2002 and 2003. Approximately 3600 marine birds were observed, with the most common species being Arctic terns ( Sterna paradisaea , N=2400) and common eiders ( Somateria mollissima borealis , N=620). We observed no Ross's gulls ( Rhodostethia rosed ) in either year, and we found ivory gulls ( Pagophila eburned ) only in 2003, even though these species commonly bred here in the 1970s. This previously unsurveyed region supports numerous breeding marine birds, but reproductive success on these small islands may be dependent on annual ice conditions and consequent movements of Arctic foxes ( Alopex lagopus ).     

Preparation and analysis of coal seam data utilizing paleoenvironment modeling,hazard #7 coal,Eastern Kentucky

Pennsylvanian strata of the Hazard coalfield, Eastern Kentucky, contain fluvial, upper-delta plain facies characterized by thick localized coals, bay-fill shales, levee silt- and sandstones, and channel-fill sands and gravels. Although the deltaic nature of these sediments has long been established, mining and exploration activities in the district require a thorough understanding of small areas within the delta environment. Coal quantity and quality trends in the Hazard #7 seam, the major producer in the area, have been examined in detail.The #7 coal accumulated in a peat swamp restricted laterally by a major fluvial channel. Three types of non-coal parting are recognized. Thin, tabular, fine-grained partings resulted from periods of increased terrigenous influx into the swamp. Lenticular crevasse-splay deposits locally split the coal. Wedge-shaped, fine- to coarse-grained partings, of probable levee origin, are found along the channel margin. Post-swamp deposits consist of thick bay-fill shales, thin shales, silt- and sandstones deposited on floodplains, and channel-fill sandstones and gravels.The modeling technique discussed provides guidance for mine development and regional exploration by prediction of coal seam quantity and quality trends from local geologic features. The thickest #7 coal is split by thin tabular partings and is overlain by thick shale sequences. Coal overlain by silt and sandstone is thinner and unsplit, and typically of higher heat value. Regional seam thinning due to channel scour is recognized. Factors which control the configuration of the coal seam include position within the peat swamp, proximity to the fluvial channel, swamp burial processes, and paleochannel sinuosity.