Simulation of torsional shear test results with neuro-fuzzy control system

In the first part of this study, a series of stress-controlled hollow cylinder cyclic torsional triaxial shear tests were conducted on loose to medium dense saturated samples of clean Toyoura sand to investigate its liquefaction behavior. A uniform cyclic sinusoidal loading at a 0.1 Hz frequency was applied to air-pluviated samples where confining pressure and relative density was varied. Cyclic shear stress–strain changes, the number of cycles to reach liquefaction and pore pressure variations were recorded. Results indicate that the liquefaction resistances of uniform sands are significantly affected by the method of sample preparation and initial conditions.     

Estimation of monotonic behavior of reinforced concrete columns considering shear‐flexure‐axial load interaction

Reinforced concrete columns with insufficient transverse reinforcement and non‐seismic reinforcement details are vulnerable to brittle shear failure and to loss of axial load carrying capacity in the event of a strong earthquake. In this paper, a procedure is presented after examining the application of two macro models for displacement‐based analysis of reinforced concrete columns subjected to lateral loads. In the proposed model, lateral load‐deformation response of the column is simulated by estimating flexural and shear deformation components separately while considering their interaction and then combining these together according to a set of rules depending upon column's yield, flexural and shear strengths. In addition, lateral deformation caused by reinforcement slip in beam–column joint regions and buckling of compression bars are taken into account and considered in the analysis. Implementation of the proposed procedure produces satisfactory lateral load–displacement relationships, which are comparable with experimental data. Copyright © 2012 John Wiley & Sons, Ltd.     

Bathymetry,substrate and fishing areas of Southeast Atlantic high-seas seamounts

Most of the Southeast Atlantic Ocean is abyssal, and global bathymetries suggest that only ～3.2% of the areas beyond national jurisdiction (ABNJ; also known as the high seas, as defined in the United Nations Convention on the Law of the Sea [UNCLOS]) are shallower than 2 500 m. This study mapped bathymetry and characterised substrates in selected seamount summit areas, including several that have been or may become fishing areas. The southernmost location, the Schmitt-Ott Seamount, has exposed volcanic bedrock with surrounding flats covered by thin biogenic sediments and/or coral rubble that appears ancient. At Wüst, Vema, Valdivia and Ewing seamounts the basaltic base appears to be overlain by coral caps and other coral substrates (sheets, rubble). Adjacent summit plains have biogenic sediments of varying thickness. Vema has a flat, roughly circular summit, <100 m deep, with the shallowest point being a 22-m-deep summit knoll; the upper slopes have ancient coral framework, but the summit has a mixture of coralline and volcanic rock and coarse sediments, including extensive areas with coralline algae and kelp forests. Valdivia Bank is a 230-m-deep, flat, rocky area (～11 × 5 km), protruding steeply from the extensive multi-summit Valdivia subarea of the Walvis Ridge. The distribution of past fisheries in the Convention Area of the South East Atlantic Fisheries Organisation (SEAFO) was considered in relation to the new information on bathymetry and substrate.     

COMPARING TRADITIONAL METHODS FOR SELECTING CLASS INTERVALS ON CHOROPLETH MAPS*

The most common goal when classing data for choropleth maps is to create homogeneous classes which contain similar data values. None of the four traditional data classing methods examined here (quartile, equal interval, standard deviation, and natural breaks) consistently generalized the experimental data sets into homogeneous classes. These methods were most accurate for data sets with specific distributional characteristics, but none classed all of any type of distribution accurately. Only the optimization method produced reliable and accurate results for all of the experimental data.     

Abundance enhancements of silicon to iron in solar energetic particles and their implications

Differential energy spectra of low abundant elements between silicon and iron of energetic solar particles (SEP) in the August 4, 1972 event were measured in the energy region of 10 to 40 MeV amu^–1 using rocket-borne Lexan detectors. The relative abundances of elements were determined and abundance enhancements, i.e., SEP/photospheric ratios, and their energy dependence were derived in 10–40 MeV amu^–1 interval. It is found that there are four types of abundance enhancements as a function of energy as follows: (a) silicon, iron, and calcium show fairly strong energy dependence which decreases with increasing energy and at 20–40 MeV amu^–1 reaches photospheric values; (b) in case of sulphur enhancement factors are independent of energy and the values are close to unity; (c) argon shows energy independent enhancements of about 3 to 4 in 10–40 MeV amu^–1; (d) titanium and chromium show weakly energy-dependent, but very high abundance enhancement factor of about 10 to 40. These features are to be understood in terms of the atomic properties of these elements and on the physical conditions in the accelerating region. These are important not only for solar phenomena but also to gain insight into the abundance enhancements of cosmic-ray heavy nuclei.on leave from Tata Institute of Fundamental Research, Bombay, India.     

Mussels (Mytilus edulis) as ‘point source’ indicators of trace metal pollution

Using X-ray Energy Spectroscopy trace metal concentrations including Pb, Cu and Zn were studied in the common blue mussel, Mytilus edulis. These organisms, sampled at intervals of only 1 km and less for a line transect study of the port of Vancouver, Canada, exhibited dramatic concentration variations. In particular, mussels only 30 m from a point source of lead displayed essentially base-line concentrations, representing a decline of two orders of magnitude.     

Hydraulic redistribution and hydrological controls on aspen transpiration and establishment in peatlands following wildfire

In the sub‐humid Western Boreal Plains of Alberta, where evapotranspiration often exceeds precipitation, trembling aspen (Populus tremuloides Michx.) uplands often depend on adjacent peatlands for water supply through hydraulic redistribution. Wildfire is common in the Boreal Plains, so the resilience of the transfer of water from peatlands to uplands through roots immediately following wildfire may have implications for aspen succession. The objective of this research was to characterize post‐fire peatland‐upland hydraulic connectivity and assess controls on aspen transpiration (as a measure of stress and productivity) among landscape topographic positions. In May 2011, a wildfire affected 90,000 ha of north central Alberta, including the Utikuma Region Study Area (URSA). Portions of an URSA glacio‐fluval outwash lake catchment were burned, which included forests and a small peatland. Within 1 year after the fire, aspen were found to be growing in both the interior and margins of this peatland. Across recovering land units, transpiration varied along a topographic gradient of upland midslope (0.42 mm hr^?1) > upland hilltop (0.29 mm hr^?1) > margin (0.23 mm hr^?1) > peatland (0.10 mm hr^?1); similar trends were observed with leaf area and stem heights. Although volumetric water content was below field capacity, P. tremuloides were sustained through roots present, likely before fire, in peatland margins through hydraulic redistribution. Evidence for this was observed through the analysis of oxygen (δ¹⁸O) and hydrogen (δ²H) isotopes where upland xylem and peat core signatures were ?10.0‰ and ?117.8‰ and ?9.2‰ and ?114.0‰, respectively. This research highlights the potential importance of hydraulic redistribution to forest sustainability and recovery, in which the continued delivery of water may result in the encroachment of aspen into peatlands. As such, we suggest that through altering ecosystem services, peatland margins following fire may be at risk to aspen colonization during succession.     

Microbial–silica interactions in Icelandic hot spring sinter: possible analogues for some Precambrian siliceous stromatolites

Silicified deposits, such as sinters, occur in several modern geothermal environments, but the mechanisms of silicification (and crucially the role of microorganisms in their construction) are still largely unresolved. Detailed examination of siliceous sinter, in particular sections of microstromatolites growing at the Krisuvik hot spring, Iceland, reveals that biomineralization contributes a major component to the overall structure, with approximately half the sinter thickness attributed to silicified microorganisms. Almost all microorganisms observed under the scanning electron microscope (SEM) are mineralized, with epicellular silica ranging in thickness from < 5 μm coatings on individual cells, to regions where entire colonies are cemented together in an amorphous silica matrix tens of micrometres thick. Within the overall profile, there appears to be two very distinct types of laminae that alternate repeatedly throughout the microstromatolite: ‘microbial’ layers are predominantly consisting of filamentous, intact, vertically aligned, biomineralized cyanobacteria, identified as Calothrix and Fischerella sp.; and weakly laminated silica layers which appear to be devoid of any microbial component. The microbial layers commonly have a sharply defined base, overlying the weakly laminated silica, and a gradational upper surface merging into the weakly laminated silica. These cyclic laminations are probably explained by variations in microbial activity. Active growth during spring/summer allows the microorganisms to keep pace with silicification, with the cell surfaces facilitating silicification, while during their natural slow growth phase in the dark autumn/winter months silicification exceeds the bacteria’s ability to compensate (i.e. grow upwards). At this stage, the microbial colony is probably not essential to microstromatolite formation, with silicification presumably occurring abiogenically. When conditions once again become favourable for growth, recolonization of the solid silica surface by free‐living bacteria occurs: cell motility is not responsible for the laminations. We have also observed that microbial populations within the microstromatolite, some several mm in depth, appear viable, i.e. they still have their pigmentation, the trichomes are not collapsed, cell walls are unbroken, cytoplasm is still present and they proved culturable. This suggests that the bulk of silicification occurred rapidly, probably while the cells were still alive. Surprisingly, however, measurements of light transmittance through sections of the microstromatolite revealed that photosynthetically active light (PAL) only transmitted through the uppermost 2 mm. Therefore the ‘deeper’ microbial populations must have either: (i) altered their metabolic pathways; (ii) become metabolically inactive; or (iii) the deeper populations may be dominated by different microbial assemblages from that of the surface. From these collective observations, it now seems unequivocal that microstromatolite formation is intimately linked to microbial activity and that the sinter fabric results from a combination of biomineralization, cell growth and recolonization. Furthermore, the similarities in morphology and microbial component to some Precambrian stromatolites, preserved in primary chert, suggests that we may be witnessing contemporaneous biomineralization processes and growth patterns analogous to those of the early Earth.     

Defect structures in naturally deformed clinoamphiboles—a TEM study

Naturally deformed clinoamphiboles from the Selbu-Tydal and Forsbäck-Tärnaby areas of the Scandinavian Caledonides exhibit a well defined subgrain microstructure. From a transmission electron microscopy study (TEM), the subgrain boundaries are shown to consist of arrays of positive and negative screw dislocations with Burgers vector . Locally expanded loops are present having long screw segments. The subgrain boundaries are parallel to rational crystallographic planes of the type (hk0). The density of isolated dislocations within the subgrains is low. In addition planar defect structures parallel to (010) and bounded by screw dislocations with are observed. Based on metamorphic criteria the P−T values at the time of the amphibole growth have been estimated at 450°–600°C and 4–6 kbar, and these represent maximum conditions for the deformation. The present results indicate that slip on (hk0) [001] is an operative deformation mechanism in naturally deformed clinoamphiboles.