DNA strand breaks in grass shrimp embryos exposed to highway runoff sediments and sediments with coal fly ash

Embryo production was reduced in female grass shrimp exposed to sediments with added coal fly ash and to sediments collected from an estuarine station containing high PAH concentrations due to its proximity to a highway storm drain. Grass shrimp embryos exposed to pore water from the high PAH and high metal sediments showed both reduced hatching and increases in DNA strand breaks (comet assay). Sediments with added coal fly ash had high concentrations of vanadium and selenium which may have contributed to effects similar to those observed with sediments with high PAH. The embryo pore water bioassay (hatching/DNA strand breaks) gave results comparable to those observed for reproduction effects (reduced embryo production/embryo hatching) with female grass shrimp exposed to whole sediment.     

Accurate pressure gradient calculations in hydrostatic atmospheric models

Most models of atmospheric flow which use the primitive equations require a diagnostic equation to determine local total pressure. In hydrostatic models, this equation is the vertically integrated hydrostatic equation. A frequently used approximation to this integration is to hold the temperature constant within model layers yielding a linear proportionality between p or (Exner's function) and z. This procedure yields static pressures with errors on the order of 10^–3mb.If terrain following coordinates are used, terms arise in the horizontal momentum equations involving the gradient of total pressure along the coordinate surface, less a correction for the variation of the hydrostatic pressure along a sloped surface. Erroneous horizontal accelerations are common in these models which result from spurious pressure gradients that are due to inaccurate computation of the static pressure. This error may be amplified if the computation of the slope correction term of the horizontal pressure gradient is not consistent with the method of calculating the total pressure.We derive a methodology to be used in the vertical pressure integrations that is exact if the potential temperature lapse rate is constant between integration limits. The method is applied to both the integration of the hydrostatic equation and the computation of the slope correction term in the horizontal pressure gradient. The method employs a fixed vertical grid and a dynamic one defined by the significant levels in the vertical temperature distribution. With this methodology, the error in calculation of the horizontal pressure gradient acceleration is greatly reduced, especially in situations where the isothermal surfaces are not parallel to the vertical coordinate surfaces. The problem of aliasing and the treatment of significant temperature levels is described.     

Probiotics as control agents in aquaculture

1 Introduction Intensive aquaculture system produces substantially higher yields than do semi-intensive systems. However, intensification results in stressful environmental changes which can produce various kinds of problems in aquatic organisms, principally diseases of diverse aetiology (Angulo, 2000). The most common control of the dis-eases was concentrated on the use of antibiotics. However,the utility of antibiotics as a preventive measure has been questioned by acquisition of genes that…     

Lithologic controls on mineralization at the Lagunas Norte high-sulfidation epithermal gold deposit, northern Peru

The 13.1-Moz high-sulfidation epithermal gold deposit of Lagunas Norte, Alto Chicama District, northern Peru, is hosted in weakly metamorphosed quartzites of the Upper Jurassic to Lower Cretaceous Chimú Formation and in overlying Miocene volcanic rocks of dacitic to rhyolitic composition. The Dafne and Josefa diatremes crosscut the quartzites and are interpreted to be sources of the pyroclastic volcanic rocks. Hydrothermal activity was centered on the diatremes and four hydrothermal stages have been defined, three of which introduced Au ± Ag mineralization. The first hydrothermal stage is restricted to the quartzites of the Chimú Formation and is characterized by silice parda, a tan-colored aggregate of quartz-auriferous pyrite–rutile ± digenite infilling fractures and faults, partially replacing silty beds and forming cement of small hydraulic breccia bodies. The δ³⁴S values for pyrite (1.7–2.2?‰) and digenite (2.1?‰) indicate a magmatic source for the sulfur. The second hydrothermal stage resulted in the emplacement of diatremes and the related volcanic rocks. The Dafne diatreme features a relatively impermeable core dominated by milled slate from the Chicama Formation, whereas the Josefa diatreme only contains Chimú Formation quartzite clasts. The third hydrothermal stage introduced the bulk of the mineralization and affected the volcanic rocks, the diatremes, and the Chimú Formation. In the volcanic rocks, classic high-sulfidation epithermal alteration zonation exhibiting vuggy quartz surrounded by a quartz–alunite and a quartz–alunite–kaolinite zone is observed. Company data suggest that gold is present in solid solution or micro inclusions in pyrite. In the quartzite, the alteration is subtle and is manifested by the presence of pyrophyllite or kaolinite in the silty beds, the former resulting from relatively high silica activities in the fluid. In the quartzite, gold mineralization is hosted in a fracture network filled with coarse alunite, auriferous pyrite, and enargite. Alteration and mineralization in the breccias were controlled by permeability, which depends on the type and composition of the matrix, cement, and clast abundance. Coarse alunite from the main mineralization stage in textural equilibrium with pyrite and enargite has δ³⁴S values of 24.8–29.4?‰ and $ {\delta^{18 }}{{\mathrm{O}}_{{\mathrm{S}{{\mathrm{O}}_4}}}} $ values of 6.8–13.9?‰, consistent with H₂S as the dominant sulfur species in the mostly magmatic fluid and constraining the fluid composition to low pH (0–2) and logfO₂ of ?28 to ?30. Alunite–pyrite sulfur isotope thermometry records temperatures of 190–260 °C; the highest temperatures corresponding to samples from near the diatremes. Alunite of the third hydrothermal stage has been dated by ⁴⁰Ar/³⁹Ar at 17.0?±?0.22 Ma. The fourth hydrothermal stage introduced only modest amounts of gold and is characterized by the presence of massive alunite–pyrite in fractures, whereas barite, drusy quartz, and native sulfur were deposited in the volcanic rocks. The $ {\delta^{18 }}{{\mathrm{O}}_{{\mathrm{S}{{\mathrm{O}}_4}}}} $ values of stage IV alunite vary between 11.5 and 11.7?‰ and indicate that the fluid was magmatic, an interpretation also supported by the isotopic composition of barite (δ³⁴S?=?27.1 to 33.8?‰ and $ {\delta^{18 }}{{\mathrm{O}}_{{\mathrm{S}{{\mathrm{O}}_4}}}} $ ?=?8.1 to 12.7?‰). The Δ³⁴S_py–alu isotope thermometry records temperatures of 210 to 280 °C with the highest values concentrated around the Josefa diatreme. The Lagunas Norte deposit was oxidized to a depth of about 80 m below the current surface making exploitation by heap leach methods viable.     

Comparative carbon emission assessments of recycled and natural aggregate concrete:Environmental influence of cement content

This work examines the environmental and geochemical impact of recycled aggregate concrete produc-tion with properties representative for structural applications.The environmental influence of cement content,aggregate production,transportation,and waste landfilling is analysed by undertaking a life cycle assessment and considering a life cycle inventory largely specific for the region.To obtain a detailed insight into the optimum life cycle parameters,a sensitivity study is carried out in which supplementary cementitious materials,different values of natural-to-recycled aggregate content ratio and case-specific transportation distances were considered.The results show that carbon emissions were between 323 and 332 kgCO2e per cubic metre of cement only natural aggregate concrete.These values can be reduced by up to 17％by replacing 25％of the cement with fly ash.By contrast,carbon emissions can increase when natural coarse aggregates are replaced by recycled aggregates in proportions of 50％and 100％,and trans-portation is not included in analysis.However,the concrete with 50％recycled aggregate presented lower increase,only 0.3％and 3.4％for normal and high strength concrete,respectively.In some cases,the rel-ative contribution of transportation to the total carbon emissions increased when cement was replaced by fly ash in proportions of 25％,and case-specific transportation distances were considered.In absolute values,the concrete mixes with 100％recycled aggregates and 25％fly ash had lower carbon emissions than concrete with cement and natural aggregates only.Higher environmental benefits can be obtained when the transportation distances of fly ash are relatively short(15-25 km)and the cement replacement by fly ash is equal or higher than 25％,considering that the mechanical properties are adequate for prac-tical application.The observations from this paper show that recycled aggregate concrete with strength characteristics representative for structural members can have lower carbon emissions than conventional concrete,recommending them as an alternative to achieving global sustainability standards in construction.     

Volcanic emissions and atmospheric pollution:A study of nanoparticles

The influence of emissions of an active volcano on the composition of nanoparticles and ultrafine road dust was identified in an urban area of the Andes.Although many cities are close to active volcanoes,few studies have evaluated their influence in road dust composition.Air quality in urban areas is significantly affected by nonexhaust emissions(e.g.road dust,brake wear,tire wear),however,natural sources such as volcanoes also impact the chemical composition of the particles.In this study,elements from volcanic emissions such as Si>Al>Fe>Ca>K>Mg,and Si-Al with K were identified as complex hydrates.Similarly,As,Hg,Cd,Pb,As,H,Cd,Pb,V,and salammoniac were observed in nanoparticles and ultrafine material.Mineral composition was detected in the order of quartz>mullite>calcite>kaolinite>illite>goethite>magnetite>zircon>monazite,in addition to salammoniac,a tracer of volcanic sources.The foregoing analysis reflects the importance of carrying out more studies relating the influence of volcanic emissions in road dust in order to protect human health.The road dust load(RD₁₀)ranged between 0.8 and 26.8 mg m^?2in the city.     

Magmatic evolution of the Mantos Blancos copper deposit, Coastal Range of northern Chile: insight from Sr–Nd isotope, geochemical data and silicate melt inclusions

The Mantos Blancos copper deposit (500 Mt at 1.0% Cu) was affected by two superimposed hydrothermal events: (i) phyllic alteration related to a rhyolitic dome emplacement and brecciation at ca 155 Ma; and (ii) potassic, sodic and propylitic alteration at ca 142 Ma, coeval with stocks and sills emplacement of dioritic and granodioritic porphyries, that locally grade upwards into polymictic magmatic hydrothermal breccias. Major hypogene copper sulfide mineralization is related to the second event. A late‐ore mafic dike swarm cross‐cuts all rocks in the deposit. Two types of granodioritic porphyries can be distinguished from petrographic observations and geochemical data: granodiorite porphyry I (GP I) and granodiorite porphyry II (GP II), which resulted from two different trends of magmatic evolution. The concave shape of the rare earth element (REE) distribution pattern together with the weak or absence of negative Eu anomalies in mafic dikes, dioritic and GP I porphyries, suggest hornblende‐dominated fractionation for this magmatic suite. In contrast, distinct negative Eu anomalies and the flat REE patterns suggest plagioclase‐dominated fractionation, at low oxygen fugacity, for the GP II porphyry suite. But shallow mixing and mingling between silicic and dioritic melts are also likely for the formation of the GP II and polymictic breccias, respectively. Sr‐Nd isotopic compositions suggest that the rhyolitic dome rocks were generated from a dominantly crustal source, while the GP I has mantle affinity. The composition of melt inclusions (MI) in quartz crystals from the rhyolitic dome is similar to the bulk composition of their host rock. The MI analyzed in quartz from GP II and in the polymictic magmatic hydrothermal breccia of the deposit are compositionally more evolved than their host rocks. Field, geochemical and petrographic data provided here point to dioritic and siliceous melt interaction as an inducing mechanism for the release of hydrothermal fluids to form the Cu mineralization.     

Bimodal back-arc alkaline magmatism after ridge subduction: Pliocene felsic rocks from Central Patagonia (47°S)

Volumetrically minor microsyenites, alkali microgranite and related trachytic dykes intrude early Pliocene OIB-like alkali basaltic and basanitic flows of the Meseta del Lago Buenos Aires in Central Patagonia (47°S–71°30′W), and occur together with scarce trachytic lava flows. Whole-rock K–Ar ages between 3.98 and 3.08 Ma indicate that the emplacement of these felsic rocks occurred more or less synchronously with that of the post-plateau basaltic sequence that they intrude, during a bimodal mafic–felsic magmatic episode devoid of intermediate compositions. Chemically, these rocks have A₁-type granitoid affinities and are characterized by high silica and alkali contents (60–68 wt.% SiO₂; 8.7–10.8 wt.% Na₂O + K₂O), major and trace elements patterns evidencing evolution by low-pressure fractional crystallization, and Sr and Nd isotopic signatures similar to those of coeval basalts ((⁸⁷Sr/⁸⁶Sr)_o = 0.70488–0.70571; (¹⁴³Nd/¹⁴⁴Nd)_o = 0.512603–0.512645). Nevertheless, some of them have the most radiogenic Sr values ever reported for a magmatic rock in the Meseta and even in the whole Neogene Patagonian Plateau Lavas province ((⁸⁷Sr/⁸⁶Sr)_o = 0.70556–0.70571; (¹⁴³Nd/¹⁴⁴Nd)_o = 0.512603–0.512608). In addition, very high contents of strongly incompatible elements in the most evolved rocks, together with Sr isotopic ratios higher than those of coeval basalts, suggest the occurrence of open-system magmatic processes. Continuous fractional crystallization from a primitive basaltic source, similar to post-plateau coeval basalts, towards alkali granites combined with small rates of assimilation of host Jurassic tuffs (AFC) in a shallow magmatic reservoir, best explains the geochemical and petrographic features of the felsic rocks. Therefore, A₁-type magmatic rocks can be generated by open-system crystallization of deep asthenospheric melts in back-arc tectonic settings.

In Central Patagonia, these  3–4 Ma old alkaline intrusions occur aligned along a  N160–170 trending lineament, the Zeballos Fault Zone, stacking the morphotectonic front of one segment of the Patagonian Cordillera. Intrusion along this fault zone occurred during the onset of a new transtensional or extensional event in the area, related to major regional tectonics occurring in possible relation with the collision of one segment of the Chile Spreading Ridge with the trench.     

Assessing multidecadal runoff (1970–2010) using regional hydrological modelling under data and water scarcity conditions in Peruvian Pacific catchments

In a context of water scarcity in Peruvian Pacific catchments as a crucial issue for Peru, added to the paucity of data availability, we propose a methodology that provides new perspectives for freshwater availability estimation as a base reference for unimpaired conditions. Under those considerations, a regional discharge of 709 m³/s to the Pacific Ocean is estimated with a significant increasing trend of about 43 m³/s per decade over the 1970 – 2010 period. To represent the multidecadal behaviour of freshwater runoff along the region, a regional runoff analysis is proposed based on hydrological modelling at annual and monthly time step for unimpaired conditions over the whole 1970 – 2010 period. Differential Split‐Sample Tests are used to assess the hydrological modelling robustness of the GR1A and GR2M conceptual lumped models, showing a satisfactory transposability from dry to wet years inside the thresholds defined for Nash–Sutcliffe and bias criteria. This allowed relating physical catchment characteristics with calibrated and validated model parameters, thus offering a regional perspective for dryland conditions in the study area (e.g., the anticlockwise hysteresis relationship found for seasonal precipitation–runoff relationship) as well as the impacts of climate variability and catchment characteristics.