滇东南富宁地区基性侵入岩及喷出岩时代

在滇东南富宁地区基性侵入岩、喷出岩较发育,前人将其划分为"半瓦型"侵入岩、"安定型"侵入岩和"龙康型"喷出岩3类,3类岩石普遍缺乏可靠的同位素年代学资料。在对富宁地区基性侵入岩、喷出岩进行区域地质调查的基础上,应用LAICP-MS技术对其进行锆石U-Pb测年,在半瓦型侵入岩和安定型侵入岩中分别获得了254.0±2.0Ma和244.2±4.4Ma的加权平均年龄,在龙康型喷出岩中获得251.9±3.0Ma和255.92±0.72Ma加权平均年龄。结合野外调查和综合研究,将富宁地区"安定型"侵入岩的时代界定于中三叠世,将"半瓦型"侵入岩和"龙康型"喷出岩的时代界定于晚二叠世。     

Groundwater sustainability and groundwater/surface-water interaction in arid Dunhuang Basin,northwest China

The Dunhuang Basin, a typical inland basin in northwestern China, suffers a net loss of groundwater and the occasional disappearance of the Crescent Lake. Within this region, the groundwater/surface-water interactions are important for the sustainability of the groundwater resources. A three-dimensional transient groundwater flow model was established and calibrated using MODFLOW 2000, which was used to predict changes to these interactions once a water diversion project is completed. The simulated results indicate that introducing water from outside of the basin into the Shule and Danghe rivers could reverse the negative groundwater balance in the Basin. River-water/groundwater interactions control the groundwater hydrology, where river leakage to the groundwater in the Basin will increase from 3,114?×?10⁴ m³/year in 2017 to 11,875?×?10⁴ m³/year in 2021, and to 17,039?×?10⁴ m³/year in 2036. In comparison, groundwater discharge to the rivers will decrease from 3277?×?10⁴ m³/year in 2017 to 1857?×?10⁴ m³/year in 2021, and to 510?×?10⁴ m³/year by 2036; thus, the hydrology will switch from groundwater discharge to groundwater recharge after implementing the water diversion project. The simulation indicates that the increased net river infiltration due to the water diversion project will raise the water table and then effectively increasing the water level of the Crescent Lake, as the lake level is contiguous with the water table. However, the regional phreatic evaporation will be enhanced, which may intensify soil salinization in the Dunhuang Basin. These results can guide the water allocation scheme for the water diversion project to alleviate groundwater depletion and mitigate geo-environmental problem.     

Acquiring high-resolution topography and performing spatial analysis of loess landslides by using low-cost UAVs

The Loess Plateau is a region in China prone to frequent geological disasters, where thousands of loess landslides can be found. Conventional field survey methods are inadequate for the requirements of fine spatial analysis of landslides. Due to its numerous advantages (fast, efficient, low cost, safe, and able to acquire high-resolution data), structure from motion (SfM) technique to photogrammetric orientation of flights and modeling applied to photographs taken by unmanned aerial vehicles (UAVs) equipped with a camera has become a powerful new tool for the generation of high-resolution topography that has emerged in recent years, which has become a powerful new technique for acquiring high-resolution topographic data. In this study, we conducted nearly two months of field UAV surveys of loess landslides on the Loess Plateau, eventually established 3D digital models for 11 loess landslides, and produced high-resolution digital orthophoto maps (DOMs) and digital elevation models (DEMs). High-resolution spatial analysis of the loess landslides (mainly including characteristic parameter extraction, topography profile analysis, surface feature analysis, and hydrologic analysis) was performed using Agisoft PhotoScan, ArcGIS 10.2, Global Mapper 17, and Origin Pro 9.0. The UAV technique allows us to further understand the micro-level internal spatial and structural characteristics of loess landslides. Moreover, not only does it allow us to accurately measure the characteristic geometric parameters but also enables us to detect the surface details of loess landslides (e.g., textures, fissures, and micro-landforms). Manifestly, we can also deduce the original structural characteristics and possible inducement mechanism of landslides based on a combination of high-resolution data acquired by UAVs, proper ground surveys, and theoretical knowledge. In summary, the low-cost UAVs are highly and especially suitable for surveys and digital terrain analysis of landslides on the Loess Plateau with sparse vegetation.     

Characterization of the mechanical properties of a claystone by nano-indentation and homogenization

Based on the analyses of mineralogical compositions by X-ray diffraction and microstructure by optical microscopy, the Young’ modulus and hardness of a claystone were characterized by the nano-indentation technique and homogenization method. Three distinct microstructural zones are identified in the claystone: clay matrix, a composite matrix of clay and small mineral grains and imbedded quartz grains. The elastic modulus and hardness of different zones were determined by nano-indentation testing. Based on the statistical analysis of nano-indentation results, the spatial mappings and frequency distributions of elastic modulus and hardness of the different zones were obtained. The elastic moduli of main constituent phases of the claystone are then estimated from the nano-indentation tests. These values were further used for the determination of the macroscopic elastic modulus of the claystone using two different homogenization schemes: the dilute scheme and Mori–Tanaka scheme. The predicted values by the homogenization schemes are compared with experimental data obtained from conventional uniaxial compression tests.     

Characterization,modeling, and remediation of karst in a changing environment

This introductory editorial paper provides a review and prospective outlook of the achievements and challenges in karst research under a changing environment. A brief discussion of the past and future karst research has been focused on: (1) data and new technologies; (2) modeling of karst flow and reactive transport; (3) responses of karst hydrosystems to climate variability and changes across scales.     

Spatial and temporal analyses of air pollutants and meteorological driving forces in Beijing–Tianjin–Hebei region,China

Due to its negative impact on the living environment of human beings, ambient air pollution has become a global challenge to human health. In this study, surface observations of six criteria air pollutants, including PM_2.5, PM₁₀, SO₂, NO₂, CO and O₃, were collected to investigate the spatial and temporal variation in the Beijing–Tianjin–Hebei (BTH) region during 2013–2016 and to explore the relationships between atmospheric pollutants and meteorological variables using quantile regression model (QRM) and multiple linear regression model (MLRM). The results show that BTH region has experienced significant air pollution, and the southern part generally has more severe conditions. The annual average indicates clear decreasing trends of the particulate matters, SO₂ and CO concentrations over the last 4 years and slight increasing trends of NO₂ and O₃ in several cities. The seasonal and monthly characteristics indicate that the concentrations of five species reach their maxima in the winter and their minima in the summer, whereas O₃ has the opposite behaviour. Finally, the pseudo R² values show that the QRMs have the best performance in the winter, followed by spring, fall, and summer. Specifically, all the meteorological factors have significant impacts on air pollution but change with pollutants and seasons. The MLRM results are generally consistent with the QRM results in all seasons, and the inconsistencies are more common in the fall and winter. The results of this research provide foundational knowledge for predicting the response of air quality to climate change in the BTH region.     

Extreme deformation characteristics and countermeasures for a tunnel in difficult grounds in southern Shaanxi,China

The Qingling–Bashan (QB) mountain region in southern Shaanxi mainly consists of strongly compressive zones from east to west, with tight folds and compressive fractures. There is a wide distribution of soft rocks of various types, such as phyllite and slate, accompanied by complex geological structures. Ironically, tunnel construction in these difficult grounds with complicated geological conditions embraces a high risk of extreme deformation due to various unpredictable reasons, which can frequently cause collapse and result in budget overruns during the construction period. Therefore, it is crucial to conduct effective countermeasures to eliminate or avoid such adverse impacts. This paper provides a case study on the “Yingfeng tunnel” (a tunnel constructed in soft rock consisting of a slate ground) based on a geological survey, indoor experiments and in situ monitoring. A successive rock mass deformation resulted in the tunnel lining seriously intruding into construction clearance and some other sections, even collapsing during the construction. The maximum displacement amount was 62.5 cm, while the maximum deformation speed reached as high as 34.18 mm/day. Additionally, to evaluate the construction impacts of tunnelling-induced geo-hazards, an investigation on extreme deformation was conducted. Considering the time-dependent features of the rock mass deformation, the constraint-convergence method was used to put forward applicable countermeasures in this paper. Finally, from the feedbacks of monitoring results, extreme deformation of the Yingfeng tunnel was effectively controlled.     

Development of efficiently coupled thermo-hydro-mechanical model to predict hydraulic fracture morphology in heavy oil reservoirs

The aim of the study involves examining the effect of heavy oil viscosity on fracture geometry in detail by establishing a heavy oil fracturing model and conventional fracturing model based on thermal–hydraulic–mechanical (THM) coupled theory, Walther viscosity model, and K–D–R temperature model. We consider viscosity and density within the heavy oil fracturing model as functions of pressure and temperature while that as constants within the conventional fracturing model. A heavy oil production well is set as an example to analyze the differences between the two models to account for the thermo-poro-elastic effect. The results show that temperature exhibits the most significant influence on the heavy oil viscosity while the influence of pressure is the least. In addition, a cooling area with a width of 0–1 m and varied length is generated near the fracture. The heavy oil viscosity increases sharply in this area, thereby indicating an area of viscosity increment. The heavy oil viscosity increases faster and is closer to wellbore, and a high viscosity increment reduces the mobility of the heavy oil and prevents the fracturing fluid from entering into the reservoir. The special viscosity distribution results in significant differences in pore pressure, oil saturation, and changing trends between these two models. In the heavy oil reservoir fracturing model, the thermal effect completely exceeds the influence of pore elasticity, and the values of the fracture length, width, and static pressure exceed those calculated in the conventional fracturing model. Thus, a comparison of the measured values indicates that the results obtained by considering viscosity as a function of temperature and pressure are more accurate. Therefore, the results of this study are expected to provide good guidelines for the design of heavy oil fracturing.     

Study of late-Mesozoic magmatic rocks and their related copper-gold-polymetallic deposits in the Guichi ore-cluster district,Lower Yangtze River Metallogenic Belt,East China

ABSTRACT

The Guichi ore-cluster district in the Lower Yangtze River Metallogenic Belt hosts extensive Cu–Au–Mo polymetallic deposits including the Tongshan Cu–Mo, Paodaoling Au, Matou Cu–Mo, Anzishan Cu–Mo, Guilinzheng Mo and Zhaceqiao Au deposits, mostly associated with the late Mesozoic magmatic rocks, which has been drawn to attention of study and exploration. However, the metallogenic relationship between magmatic rocks and the Cu–Au-polymetallic deposits is not well constrained. In this study, we report new zircon U–Pb ages, Hf isotopic, and geochemical data for the ore-bearing intrusions of Guichi region. LA-ICP-MS U–Pb ages for the Anzishan quartz diorite porphyrite is 143.9 ± 1.0 Ma. Integrated with previous geochronological data, these late Mesozoic magmatic rocks can be subdivided into two stages of magmatic activities. The first stage (150–132 Ma) is characterized by high-K calc-alkaline intrusions closely associated with Cu–Au polymetallic ore deposits. Whereas, the second stage (130–125 Ma) produced granites and syenites and is mainly characterized by shoshonite series that are related to Mo–Cu mineralization. The first stage of magmatic rocks is considered to be formed by partial melting of subducted Palaeo-Pacific Plate, assimilated with Yangtze lower crust and remelting Meso-Neoproterozoic crust/sediments. The second stage of magmatism is originated from partial melting of Mesoproterozoic-Neoproterozoic crust, mixed with juvenile crustal materials. The depression cross to the uplift zone of the Jiangnan Ancient Continent forms a gradual transition relation, and the hydrothermal mineralization composite with two stages have certain characteristics along the regional fault (Gaotan Fault). Guichi region results from two episodes of magmatism probably related to tectonic transition from subduction of Palaeo-Pacific Plate to back-arc extensional setting between 150 and 125 Ma, which lead to the Mesozoic large-scale polymetallic mineralization events in southeast China.     

印度尼西亚苏门答腊岛Woyla金矿流体包裹体研究及矿床成因分析

印度尼西亚Woyla金矿床位于西苏门答腊地体北段,为一中型规模的金矿床。本文通过对含矿石英脉开展详细的流体包裹体显微测温、成分分析,结合石英的H-O同位素和黄铁矿的S同位素特征分析,结果如下：其中,流体包裹体研究结果表明,含金石英脉中的石英主要发育气液两相包裹体,包裹体均一温度变化范围为152～324℃,集中在200～280℃。盐度为(0.88～6.16)wt%NaCleqv,集中在(1.00～3.00)wt%NaCleqv,成矿流体密度为0.70～0.94g/cm3,平均为0.82g/cm3。成矿压力为9.63～25.84MPa,平均值为18.37 MPa。成矿深度为0.96～2.58km,平均为1.86km,以上显示Woyla矿床成矿流体具有中低温低盐度和浅成的特征。包裹体气、液相成分测定显示气相成分以H2、N2、CO 、CO2、CH4和H2O为主;液相成分中阳离子以Na+、K+和Ca2+为主,阴离子以富SO42-和Cl-为特征,成矿流体属Cl--SO42--Ca2+-K+型。氢氧同位素测定显示成矿流体δ18DV-SMOW=-78.3‰～-92.4‰,δ18OH2O=-3.0‰～-5.5‰,主要来自大气降水,可能有少量岩浆水参与。黄铁矿硫同位素组成为-0.21‰～1.22‰,平均值为0.34‰,说明成矿物质的S具有深源岩浆硫的特征。结合矿床地质特征和成矿流体研究,首次提出Woyla金矿床属典型的低硫型浅成低温热液型金矿床。