Wet Fault or Dry Fault? A Laboratory Approach to Remotely Monitor the Hydro-Mechanical State of a Discontinuity Using Controlled-Source Seismics

Stress variation and fluid migration occur in deformation zones, which are expected to affect seismic waves reflected off or propagating across such structures. We developed a basic experimental approach to monitor the mechanical coupling with respect to seismic coupling across a single discontinuity between a granite sample in contact with a steel platen. Piezoceramics located on the platen were used to both generate and record the P and S wave fields reflected off the discontinuity at normal incidence. This way, normal (B _n ) and tangential (B _t ) compliances were calculated using Schoenberg’s linear slip theory (Schoenberg, J Acoust Soc Am 68:1516–1521, 1980) when the roughness, the effective pressure (P _eff, up to 200 MPa), and the nature of the filling (gas or water) vary. We observe that increasing the effective pressure decreases B _n and B _t , which is interpreted as the effect of the closure of the voids at the interface, permitting more seismic energy to be transmitted across the interface. Values of B _n are significantly higher than those of B _t at low P _eff (<60–80 MPa) in dry conditions, and significantly drop under water-saturated conditions. The water filling the voids therefore helps to transmit the seismic energy of compressional waves across the interface. These results show that the assumption B _n  ≈ B _t commonly found in some theoretical approaches does not always stand. The ratio B _n /B _t actually reflects the type of saturating fluids and the effective pressure, in agreement with other experimental studies. However, we illustrate that only the relative variations of this ratio seem to be relevant, not its absolute value as suggested in previous studies. Consequently, the use of B _n against B _t plots may allow effective pressure variation and the nature of the pore fluid to be inferred. In this respect, this experimental approach at sample scale helps to pave the way for remotely monitoring in the field the hydro-mechanical state of deformation zones, such as seismogenic faults, fractured reservoirs, or lava conduits.     

Characterizing and classifying urban watersheds with compositional and structural attributes

Current land-use classifications used to assess urbanization effects on stream water quality date back to the 1980s when limited information was available to characterize watershed attributes that mediate non-point source pollution. With high resolution remote sensing and widely used GIS tools, there has been a vast increase in the availability and precision of geospatial data of built environments. In this study, we leverage geospatial data to expand the characterization of developed landscapes and create a typology that allows us to better understand the impact of complex developed landscapes across the rural to urban gradient. We assess the ability of the developed landscape typology to reveal patterns in stream water chemistry previously undetected by traditional land-cover based classification. We examine the distribution of land-cover, infrastructure, topography and geology across 3876 National Hydrography Dataset Plus catchments in the Piedmont region of North Carolina, USA. From this dataset, we generate metrics to evaluate the abundance, density and position of landscape features relative to streams, catchment outlets and topographic wetness metrics. While impervious surfaces are a key distinguishing feature of the urban landscape, sanitary infrastructure, population density and geology are better predictors of baseflow stream water chemistry. Unsupervised clustering was used to generate a distinct developed landscape typology based on the expanded, high-resolution landscape feature information. Using stream chemistry data from 37 developed headwater catchments, we compared the baseflow water chemistry grouped by traditional land-cover based classes of urbanization (rural, low, medium and high density) to our composition and structure-based classification (a nine-class typology). The typology based on 22 metrics of developed landscape composition and structure explained over 50% of the variation in NO₃⁻-N, TDN, DOC, Cl⁻, and Br⁻ concentration, while the ISC-based classification only significantly explained 23% of the variation in TDN. These results demonstrate the importance of infrastructure, population and geology in defining developed landscapes and improving discrete classes for water management.     

Comparison of surface and borehole locations of induced seismicity

Monitoring of induced microseismic events has become an important tool in hydraulic fracture diagnostics and understanding fractured reservoirs in general. We compare microseismic event and their uncertainties using data sets obtained with surface and downhole arrays of receivers. We first model the uncertainties to understand the effect of different acquisition geometries on location accuracy. For a vertical array of receivers in a single monitoring borehole, we find that the largest part of the final location uncertainty is related to estimation of the backazimuth. This is followed by uncertainty in the vertical position and radial distance from the receivers. For surface monitoring, the largest uncertainty lies in the vertical position due to the use of only a single phase (usually P‐wave) in the estimation of the event location. In surface monitoring results, lateral positions are estimated robustly and are not sensitive to the velocity model. In this case study, we compare event location solutions from two catalogues of microseismic events; one from a downhole array and the second from a surface array of 1C geophone. Our results show that origin time can be reliably used to find matching events between the downhole and surface catalogues. The locations of the corresponding events display a systematic shift consistent with a poorly calibrated velocity model for downhole dataset. For this case study, locations derived from surface monitoring have less scatter in both vertical and horizontal directions.     

Post-collapse volcanic history of calderas on a composite volcano: an example from Roccamonfina,southern Italy

Roccamonfina, part of the Roman Potassic Volcanic Province, is an example of a composite volcano with a complex history of caldera development. The main caldera truncates a cone constructed predominantly of this caldera may have been associated with one of the ignimbritic eruptions of the Brown Leucitic Tuff (BLT) around 385 000 yr BP. The Campagnola Tuff, the youngest ignimbrite of the BLT, however, drapes the caldera margin and must postdate at least the initial stages of collapse. During the subsequent history of the caldera there were several major explosive eruptions. The largest of these was that of the Galluccio Tuff at about 300 000 yr BP. It is likely that there was further collapse within the main caldera associated with these eruptions. It is of note that despite these subsequent major explosive eruptions later collapse occurred within the confines of the main caldera. Between eruptions caldera lakes developed producing numerous lacustrine beds within the caldera fill. Extensive phases of phreatomagmatic activity generated thick sequences of pyroclastic surge and fall deposits. Activity within the main caldera ended with the growth of a large complex of basaltic trachyandestite lava domes around 150 000 yr BP. Early in the history of Roccamonfina sector collapse on the northern flank of the volcano formed the northern caldera. One of the youngest major events on Roccamonfina occurred at the head of this northern caldera with explosive activity producing the Conca Ignimbrite and associated caldera. There is no evidence that there was any linkage in the plumbing systems that fed eruptions in the main and northern calderas.     

Placing geographies of public health

Following the move to a 'post–medical' geography, a large amount of research has come to focus on public health issues. This paper explores these current geographies of public health and argues for the development of a more critical perspective. In particular, it draws on commentary that has emerged out of debates that have taken place within a body of literature usually identified as the critical 'new' public health. The paper goes on to argue that such scholarship offers crucial insights for the production of a critical geography of public health.     

William Smith's map brought alive by digital remastering

The geological mapping carried out by William Smith, which resulted in the publication of his famous map in 1815, was remarkable in many respects, not least because it relied on him being able to make consistent and accurate observations on the rock types he encountered during his fieldwork. This ability, gained from his many years studying rocks, allowed him to observe features with his own eyes (or at the very least, with the aid of a simple magnifying device) that others could not. We take a new look at William Smith's original stratigraphical sequences, and with samples collected from his classic field areas (many of which are around the city of Bath, Somerset, UK), demonstrate how spatial mineralogy mapping can be incorporated into the modern age of digital mapping.     

Petrological imaging of an active pluton beneath Cerro Uturuncu,Bolivia

Uturuncu is a dormant volcano in the Altiplano of SW Bolivia. A present day ~70 km diameter interferometric synthetic aperture radar (InSAR) anomaly roughly centred on Uturuncu’s edifice is believed to be a result of magma intrusion into an active crustal pluton. Past activity at the volcano, spanning 0.89 to 0.27 Ma, is exclusively effusive and almost all lavas and domes are dacitic with phenocrysts of plagioclase, orthopyroxene, biotite, ilmenite and Ti-magnetite plus or minus quartz, and microlites of plagioclase and orthopyroxene set in rhyolitic groundmass glass. Plagioclase-hosted melt inclusions (MI) are rhyolitic with major element compositions that are similar to groundmass glasses. H₂O concentrations plotted versus incompatible elements for individual samples describe a trend typical of near-isobaric, volatile-saturated crystallisation. At 870 °C, the average magma temperature calculated from Fe–Ti oxides, the average H₂O of 3.2 ± 0.7 wt% and CO₂ typically <160 ppm equate to MI trapping pressures of 50–120 MPa, approximately 2–4.5 km below surface. Such shallow storage precludes the role of dacite magma emplacement into pre-eruptive storage regions as being the cause of the observed InSAR anomaly. Storage pressures, whole-rock (WR) chemistry and phase assemblage are remarkably consistent across the eruptive history of the volcano, although magmatic temperatures calculated from Fe–Ti oxide geothermometry, zircon saturation thermometry using MI and orthopyroxene-melt thermometry range from 760 to 925 °C at NNO ± 1 log. This large temperature range is similar to that of saturation temperatures of observed phases in experimental data on Uturuncu dacites. The variation in calculated temperatures is attributed to piecemeal construction of the active pluton by successive inputs of new magma into a growing volume of plutonic mush. Fluctuating temperatures within the mush can account for sieve-textured cores and complex zoning in plagioclase phenocrysts, resorption of quartz and biotite phenocrysts and apatite microlites. That Fe–Ti oxide temperatures vary by ~50–100 °C in a single thin section indicates that magmas were not homogenised effectively prior to eruption. Phenocryst contents do not correlate with calculated magmatic temperatures, consistent with crystal entrainment from the mush during magma ascent and eruption. Microlites grew during ascent from the magma storage region. Variability in the proportion of microlites is attributed to differing ascent and effusion rates with faster rates in general for lavas >0.5 Ma compared to those <0.5 Ma. High microlite contents of domes indicate that effusion rates were probably slowest in dome-forming eruptions. Linear trends in WR major and trace element chemistries, highly variable, bimodal mineral compositions, and the presence of mafic enclaves in lavas demonstrate that intrusion of more mafic magmas into the evolving, shallow plutonic mush also occurred further amplifying local temperature fluctuations. Crystallisation and resorption of accessory phases, particularly ilmenite and apatite, can be detected in MI and groundmass glass trace element covariation trends, which are oblique to WRs. Marked variability of Ba, Sr and La in MI can be attributed to temperature-controlled, localised crystallisation of plagioclase, orthopyroxene and biotite within the evolving mush.     

The shipway limestone of gower: Sedimentation on a storm-dominated early carboniferous ramp

A detailed sedimentary study of the Lower Carboniferous (Courceyan) Shipway Limestone Formation at Three Cliffs Bay on the Gower Peninsula (South Wales) has shown that the bioclastic limestones represent a storm-dominated sequence that contains the storm-related sedimentary structure hummocky cross-stratification (HCS). Conformably overlying the Shipway Limestone is a cross-stratified oolitic sandbody with evidence of subaerial exposure. Six sedimentary lithofacies are identified in these two formations which record a distal to proximal, shallowing-upward trend that passes from beneath mean wave-base to above fairweather wave-base. The shallow marine facies model constructed by Wu (1982) from his study of the Lower Carboniferous limestone sequences of South Wales is re-evaluated. Modifications proposed for the model include the addition of two distal tempestite facies and a proximal oolite sand body. The Shipway Limestone and Brofiscin Oolite record the first major, basin-wide, shallowing-upward phase of the Lower Carboniferous in South Wales.     

Direct physical evidence of dolomite recrystallization

The possibility of recrystallization is a long‐standing barrier to deciphering the genetic origin of dolomites. There is often uncertainty regarding whether or not characteristics of ancient dolomites are primary or the consequence of later recrystallization unrelated to the original dolomitization event. Results from 65 new high‐temperature dolomite synthesis experiments (1 m , 1·0 Mg/Ca ratio solutions at 218°C) demonstrate dolomite recrystallization affecting stoichiometry, cation ordering and nanometre‐scale surface texture. The data support a model of dolomitization that proceeds by a series of four unique phases of replacement and recrystallization, which occur by various dissolution–precipitation reactions. During the first phase (induction period), no dolomite forms despite favourable conditions. The second phase (replacement period) occurs when Ca‐rich dolomite products, with a low degree of cation ordering, rapidly replace calcite reactants. During the replacement period, dolomite stoichiometry and the degree of cation ordering remain constant, and all dolomite crystal surfaces are covered by nanometre‐scale growth mounds. The third phase (primary recrystallization period), which occurs in the experiments between 97% and 100% dolomite, is characterized by a reduced replacement rate but concurrent increases in dolomite stoichiometry and cation ordering. The end of the primary recrystallization period is marked by dolomite crystal growth surfaces that are covered by flat, laterally extensive layers. The fourth phase of the reaction (secondary recrystallization period) occurs when all calcite is consumed and is characterized by stoichiometric dolomite with layers as well as a continued increase in the degree of cation ordering with time. Inferences of recrystallization, in natural dolomite, based on cation order or stoichiometry of dolomite, usually depend on assumptions about the precursor dolomite subjected to recrystallization. If it is assumed that the experimental evidence presented here is applicable to natural, low‐temperature dolomites, then the presence of mounds is direct evidence of a lack of recrystallization and the presence of layers is direct evidence of recrystallization.     

The quaternary stratigraphy of mount Etna,sicily: the effects of differing palaeoenvironments on styles of volcanism

Using recently published radiometric dates of important horizons within the Etna succession, correlations are proposed with the Late Quaternary biostratigraphies of the Italian mainland and the Mediterranean sea floor. This enables palaeoclimatic, palaeohydrological and palaeogeographical conditions on Etna to be established at stages in the volcano's evolution. It is argued that several major volcaniclastic suites were formed through the operation of processes that were under complex environmental, rather than simple volcanological control alone. In particular it is suggested that certain episodes of phreatomagmatic and laharic activity cannot be related to episodes of more evolved magma production, but rather to times during which the environment, height and configuration of Etna favoured the eruption and emplacement of these deposits. The authors reiterate their explanation of the formation of the Valle del Bove through processes of massive slope failure and indicate that conditions favouring this occurred at an appropriate stage in the history of the volcano. It is concluded that on active basaltic volcanoes, especially those like Etna which are also high mountains, the explanation of more violent phases requires the consideration of both internal volcanological and external environmental and morphological variables and that this is particularly important when its development has been set within the context of Late Quaternary environmental change. Finally the implications of these findings for the assessment of hazard are considered.

---

Resumé Utilisant récemment des publications sur les datations radiométriques de couches importantes à l'intérieur de la succession de l'Etna, nous proposons d'établir des corrélations entre les biostratigraphies du Quaternaire Récent de la Péninsule Italienne et due fond marin Méditerranéen. Par ce procédé, nous pouvons établir les conditions paléoclimatiques, paléohydrologiques et paléogéographiques par stades selon l'évolution du volcan, capendant il faut tenir compte du fait que plusieurs suites volcaniclastiques majeures se sont formées à partir d'opérations de processus qui etaient eux-mêmes sous une complexe influence écologique plutôt que volcanologique seulement. Il est suggéré, en particulier, que certains épisodes d'activités phreatomagmatiquer et laharique ne puissent être reliés à des épisodes de production de magma plus elaborée, mais plutôt à des périodes pendant lesquelles le milieu, la hauteur et la configuration de l'Etna ont favorisé l'éruption et la localisation de ces dépôts. Les auteurs réitèrant leur explication sur la formation de la Vallée del Bove selon un processus de rupture radicale de pente et indiquent que les conditions favorables à ce dernier sont survenues à un stade opportun dans l'histoire du volcan. Ceci amènè à conclure que, sur des volcans basaltiques actifs comme l'Etna en particulier qui sont egalement des montagnes élevées, l'explication de phases plus violentes demande la consideration de facteurs volcanologiques internes d'une part, et morphologiques et écologiques externes d'autre part et que ceci est essential lorsque son développement a été fixé dans le contexte du changement de milieu au Quaternaire Recent. Enfin, il faut tenir compte de l'implication de ces résultats face aux incidences de risques.