Mechanics and performance of a tied-back wall under seismic loads

In this paper the stability of a tied-back wall subjected to seismic loads is analysed for a predetermined mode of failure (rotation about the top of the wall) and the analysis is compared with data from tests on this type of wall using the seismic simulator at the State University of New York at Buffalo. We carried out a pseudo-static analysis of the problem using the Mononobe-Okabe earth pressure coefficients, wherein the dynamic effects due to the seismic loading are converted into equivalent static loads. The acceleration ratio at which the wall fails by rotation about the top was obtained by considering the moments due to the various lateral earth pressure resultants and the inertial forces induced in the soil due to the seismic loading. We found that the presence of wall friction on the passive side significantly enhances the stability of the flexible retaining wall under seismic loads. Thus, flexible retaining walls supporting dry cohesionless soil can be very efficient during earthquakes. Under moderate earthquakes, an increase in the depth of embedment increases the dynamic factor of safety significantly. However, beyond a certain acceleration ratio for a soil with a particular value of ø, any increase in the depth of emdedment has no effect in impeding failure, irrespective of any change in the geometry of the system. Seismic design charts are presented to evaluate the stability of, and to design, flexible retaining walls embedded in dry cohesionless soils under seismic loading.     

Relationships between marginal thrusting and movement on major,internal shear zones in the Northern Highland Caledonides,Scotland

The development of the syn-metamorphic Sgurr Beag slide zone, a major ductile shear zone of initially low dip, caused at least 50 km north-western thrust displacement of part of the internal metamorphic complex of the Northern Highland Caledonides of Scotland. Initiation of the zone, and movements upon it, were earlier than formation of the marginal Moine Thrust zone. Movement on the zone followed but overlapped the peak Caledonian metamorphism and the mid to high amphibolite facies mineral assemblages, fabrics and structures produced during the development of the slide zone and those surviving from earlier events, were reworked under greenschist facies conditions during mylonitization associated with initiation of the Moine Thrust zone. Displacements on the slide zone and thrust movements were separated by emplacement of a regional suite of pegmatites and a considerable change of metamorphic grade. Thus, they may not constitute members of a progressive sequence of Caledonian thrusts formed over a short time interval. Rather, preliminary isotopic data may imply an interval of c. 25 Ma between movement on the slide zone and final, ductile translation along the Moine Thrust zone.     

Rapid entrenchment of stream profiles in the salt caves of Mount Sedom,Israel

Rock salt is approximately 1000 times more soluble than limestone and thus displays high rates of geomorphic evolution. Cave stream channel profiles and downcutting rates were studied in the Mount Sedom salt diapir, Dead Sea rift valley, Israel. Although the area is very arid (mean annual rainfall ≈ 50 mm), the diapir contains extensive karst systems of Holocene age. In the standard cave profile a vertical shaft at the upstream end diverts water from a surface channel in anhydrite or clastic cap rocks into the subsurface route in the salt. Mass balance calculations in a sample cave passage yielded downcutting rates of 0–2 mm s^?1 during peak flood conditions, or about eight orders of magnitude higher than reported rates in any limestone cave streams. However, in the arid climate of Mount Sedom floods have a low recurrence interval with the consequence that long-term mean downcutting rates are lower: an average rate of 8·8 mm a^?1 was measured for the period 1986–1991 in the same sample passage. Quite independently, long-term mean rates of 6·2mm a^?1 are deduced from ¹⁴C ages of driftwood found in upper levels of 12 cave passages. These are at least three orders of magnitude higher than rates established for limestone caves. Salt cave passages develop in two main stages: (1) an early stage characterized by high downcutting rates into the rock salt bed, and steep passage gradients; (2) a mature stage characterized by lower downcutting rates, with establishment of a subhorizontal stream bed armoured with alluvial detritus. In this mature stage downcutting rates are controlled by the uplift rate of the Mount Sedom diapir and changes of the level of the Dead Sea. Passages may also aggrade. These fast-developing salt stream channels may serve as full-scale models for slower developing systems such as limestone canyons.     

Composition and origin of clasts and inclusions in the Abee enstatite chondrite breccia

The concentrations of 25 major, minor and trace elements have been determined in four clasts, a metal-rich inclusion and two dark metal-poor inclusions from the Abee enstatite chondrite. The clasts are heterogeneous, displaying 2-fold enrichments or depletions in some elements. The data suggest that there are two generations of metal, one with low, the other with high concentrations of refractory siderophiles. The other elemental patterns can be understood in terms of variations in the abundance of major minerals. We infer that Sc and Mn are located largely in the niningerite ((Fe,Mg)S), V in the troilite (FeS) and rare earth elements in the oldhamite (CaS).Heterogeneities among the clasts are probably primary, resulting from the accretion-agglomeration process, although shock processes in a regolithic setting remain a possibility provided that they were followed by a period of metamorphism sufficient to erase petrologic evidence.In the dark inclusions the concentrations of the rare earths, Eu excepted, are 4 × higher than mean EH levels; this infers enhanced amounts of CaS. The dark inclusions are low in siderophiles, Sc, Mn, K, Na and Al, implying low amounts of metal, niningerite and feldspar. The origin of the dark inclusions is unclear; they do not appear to be the result of a simple, single-stage process.