Partial melting and P–T evolution of the Kodaikanal Metapelite Belt, southern India

The Kodaikanal region of the Madurai Block in southern India exposes a segment of high-grade metamorphic rocks dominated by an aluminous garnet–cordierite–spinel–sillimanite–quartz migmatite suite, designated herein as the Kodaikanal Metapelite Belt (KMB). These rocks were subjected to extreme crustal metamorphism during the Late Neoproterozoic despite the lack of diagnostic ultrahigh-temperature assemblages. The rocks preserve microstructural evidence demonstrating initial-heating, dehydration melting to generate the peak metamorphic assemblage and later retrogression of the residual assemblages with remaining melt. The peak metamorphic assemblage is interpreted to be garnet + sillimanite + K-feldspar + spinel + Fe–Ti oxide + quartz + melt, which indicates pressure–temperature (P–T) conditions around 950–1000 °C and 7–8 kbar based on calculated phase diagrams. A clockwise P–T path is proposed by integrating microstructural information with pseudosections. We show that evidence for extreme crustal metamorphism at ultrahigh-temperature conditions can be extracted even in the cases where the rocks lack diagnostic ultrahigh-temperature mineral assemblages. Our approach confirms the widespread regional occurrence of UHT metamorphism in the Madurai Block during Gondwana assembly and point out the need for similar studies on adjacent continental fragments.     

Deformation-induced garnet zoning

Compositional zoning patterns in garnet porphyroblasts from kyanite-bearing samples of the Devonian Littleton Formation, north-central Massachusetts, reveal complex patterns of growth that are related to multiple deformation and metamorphic events. Garnet porphyroblasts exhibit asymmetrical and irregular zoning patterns in X_Mn, X_Ca and Fe/(Fe + Mg). Zoning reversals in Mn and Fe/(Fe + Mg) and patch distribution in Ca appear to occur around the boundaries of the textural zones. Also, the compositions of the garnet at the textural boundaries are variable for all traverses. These observations suggest that the garnet zoning was not only modified from diffusion processes, but was also influenced by pre-existing microfabrics through the effects of preferential dissolution and resorption in partial disequilibrium. Relationships between chemical and textural truncations indicate that the zoning patterns of garnet were strongly modified from preferential dissolution and precipitation during the development of successive foliations that occurred in zones of high strain/stress (cleavage seams) and zones of low strain/stress, respectively.     

Food Deserts in the Prairies? Supermarket Accessibility and Neighborhood Need in Edmonton,Canada*

The U.S. and U.K. literatures have discussed “food deserts,” reflecting populated, typically urban, low‐income areas with limited access to full‐service supermarkets. Less is known about supermarket accessibility within Canadian cities. This article uses the minimum distance and coverage methods to determine supermarket accessibility within the city of Edmonton, Canada, with a focus on high‐need and inner‐city neighborhoods. The results show that for 1999 both of these areas generally had higher accessibility than the remainder of the city, but six high‐need neighborhoods had poor supermarket accessibility. We conclude by examining potential reasons for differences in supermarket accessibility between Canadian, U.S., and U.K. cities.     

An optimal determination of variable antenna height and power for in-orbit SAR operations

An optimal power and antenna height determination over a wide range of incidence angles is proposed for in-orbit operations of the spaceborne stripmap synthetic aperture radar (SAR) with variable antenna height and variable radiating element power. The antenna height and the average transmitted radio-frequency power of a radiating element for each incidence angle are determined so that the mapping area can be maximized with the constraints on the signal-to-noise ratio, ambiguities, and swath width, given the SAR geometry (an altitude and incidence angles) and radar wavelength. With the receive-chain power consumption of one transmit/receive module (P/sub r/=10 mW) and the SAR instrument power consumption without the phased array antenna (P/sub I/=5 W), the illustrative design example shows that the mapping area of the proposed SAR for the maximum incidence angle (/spl eta//sup max/=75/spl deg/) is about 269.1% of that resulted from utilizing only the variable antenna height. The proposed optimization would have a more beneficial effect on applications that need the high-incidence-angle operations.     

Tests on low‐ductility RC frames under high‐ and low‐frequency excitations

The response of low‐ductility reinforced concrete (RC) frames, designed typically for a non‐seismic region, subjected to two frequencies of base excitations is studied. Five half‐scaled, two‐bay, two‐storey, RC frames, each approximately 5 m wide by 3.3 m high, were subjected to both horizontal and/or vertical base excitations with a frequency of 40 Hz as well as a lower frequency of about 4 Hz (close to the fundamental frequency) using a shake table. The imposed acceleration amplitude ranged from 0.2 to 1.2g. The test results showed that the response characteristics of the structures differed under high‐ and low‐frequency excitations. The frames were able to sustain high‐frequency excitations without damage but were inadequate for low‐frequency excitations, even though the frames exhibited some ductility. Linear‐elastic time‐history analysis can predict reasonably well the structural response under high‐frequency excitations. As the frames were not designed for seismic loads, the reinforcement detailing may not have been adequate, based on the crack pattern observed. The effect of vertical excitation can cause significant additional forces in the columns and moment reversals in the beams. The ‘strong‐column, weak‐beam’ approach for lateral load RC frame design is supported by experimental observations. Copyright © 2001 John Wiley & Sons, Ltd.     

Optimal design of passive energy dissipation systems based on H∞ and H2 performances

Passive energy dissipation devices (EDDs), such as viscous dampers, viscoelastic dampers, etc., have been used to effectively reduce the dynamic response of civil infrastructures, such as buildings and bridges, subject to earthquakes and strong winds. The design of these passive energy dissipation devices (EDDs) involves the determination of the optimal locations and the corresponding capacities. In this paper, we present two optimal design methodologies for passive EDDs based on active control theories, including H_∞ and H₂ performances, respectively. The optimal design methodologies presented are capable of determining the optimal locations and the corresponding capacities of EDDs. Emphasis is placed on the application of linear matrix inequality (LMI) for the effective design of passive EDDs using the popular MATLAB toolboxes. One important advantage of the proposed approaches is that the computation of the structural response is not needed in the design process. The proposed optimal design methodologies have been applied to: (i) a 10‐storey building and a 24‐storey building both subject to earthquake excitations, and (ii) a 76‐storey wind‐excited benchmark building, to demonstrate the advantages of the proposed design methodologies over the conventional equal capacity design. Copyright © 2002 John Wiley & Sons, Ltd.     

应用CP网络进行岩性识别

为通过测井解决岩性识别问题，引入了具有分类准确、算法简练等优点的CP（Counter-Propagation)网络。在详细介绍CP网络的网络模型和算法的基础上，结合某油田的实际测井资料，进行了CP网络识别研究。应用结果表明：CP网络训练周期短、识别准确率高、不存在收敛问题。通过试验研究得出结论：CP网络完全可以用于解决岩性识别等问题，具有广阔的应用前景。     

离散裂隙渗流方法与裂隙化渗透介质建模

流体渗流模拟的连续介质方法通常适用于多孔地质体，并不一定适用于裂隙岩体，由于裂隙分布及其特征与孔隙差异较大。若流体渗流主要受裂隙的控制，对于一定尺寸的裂隙岩体，多孔介质假设则较难刻划裂隙岩体的渗流特征。离散裂隙渗流方法不但可直接用于模拟裂隙岩体非均质性和各向异性等渗流特征，而且可用其确定所研究的裂隙岩体典型单元体及其水力传导（渗透）张量大小。主要讨论了以下问题：（1）饱和裂隙介质中一般的离散流体渗流模拟；（2）裂隙岩体中的REV（典型单元体）及其水力传导（渗透）张量的确定；（3）利用离散裂隙网络流体渗流模型研究裂隙方向几何参数对水力传导系数和REV的影响；（4）在二维和三维离散裂隙流体渗流模型中对区域大裂隙和局部小裂隙的处理方法。调查结果显示离散裂隙流体渗流数学模型可用来评价不同尺度上的裂隙岩体的水力特征，以及裂隙方向对裂隙化岩体的水力特征有着不可忽视的影响。同时，局部小裂隙、区域大裂隙应当区别对待，以便据其所起的作用及水力特征，建立裂隙化岩体相应的流体渗流模型。