Environmental impacts of bench blasting at Hisarcik Boron open pit mine in Turkey

This paper presents the results of ground vibration measurements carried out in Hisarcik Boron open pit mine located on the west side of central Anatolia near Kütahya province in Turkey. Within the scope of this study to predict peak particle velocity (PPV) level for this site, ground vibration components were measured for 304 shots during bench blasting. In blasting operations, ANFO (blasting agent), gelatin dynamite (priming), and delay electric detonators (firing) were used as explosives. Parameters of scaled distance (charge quantity per delay and the distance between the source and the station) were recorded carefully and the ground vibration components were measured for all blast events using two different types of vibration monitors (one White Mini-Seis and one Instantel Minimate Plus Model). The absolute distances between shot points and monitor stations were determined using GPS. The equation of square root scaled distance extensively used in the literature was taken into consideration for the prediction of PPV. Then, the data pairs of scaled distance and particle velocity obtained from the 565 event records were analyzed statistically. At the end of statistical evaluation of the data pairs, an empirical relation which gives 50% prediction line with a reasonable correlation coefficient was established between PPV and scaled distance.     

Evaluating the production and bio-stimulating effect of 5-methyl 1, hydroxy phenazine on microbial fuel cell performance

The role of endogenous redox mediators has considerable importance in electron shuttling reactions and associated performance of microbial fuel cell. Single-chamber microbial fuel cell-II with dual air-cathode assembly (area = 18.84 cm²) supported highest bacterial (Pseudomonas aeruginosa) density (6.7 × 10⁹) and active biomass [4.4 ± 0.3 mg cm^?2 (carbon content = 0.48 ± 0.1 mg cm^?2)] on anode thereby resulting in maximum production of redox metabolite, 5-methyl 1, hydroxy phenazine (301 ppm) and voltage (595 ± 5 mV) than similar cells with relatively less surface area of cathode. It was further revealed that 5-methyl 1, hydroxy phenazine production was positively correlated with chemical oxygen demand removal rate (77 ± 2.5%) and power generation (66.6 ± 2.2 mW cm^?2) efficiency of single-chamber microbial fuel cell-II. Maximum power density of 258 ± 4.5 mW cm^?2 was generated when reactor was supplemented with 2 ml crude extract of 5-methyl 1, hydroxy phenazine metabolite, whereas power output was about 229 ± 2.5 mW cm^?2 when reactor was bio-stimulated with 1 ml pure extract of 5-methyl 1, hydroxy phenazine. With this concentration, the electrochemical response of mixed culture biofilm (sediment) was enhanced by 99.3%. However, further increase in concentration of endogenous mediator proved to be limiting on reactor performance. Pyrosequencing and phylogenetic analysis on the basis of partial 16S rRNA sequences demonstrated both culturable and unculturable bacterial species in anodic biofilm and relative abundance of family Pseudomonadaceae was found to be maximum, i.e., 61.7% followed by Rhodocyclaceae 19.2%, Xanthomonadaceae 6.3% and Opitutaceae 3.18%.     

Feasibility,emission and fuel requirement analysis of hybrid car versus solar electric car: a comparative study

The problem regarding environment has been considered as contemporary issue, and to cater this, various technologies have been revolutionized in vehicle transport field. Efforts have been made to make vehicle engine efficient and introducing hybridized vehicles with the aim of reducing emissions and less fuel dependency. In essence of this, trends of solar electric cars in different countries have been reviewed. Feasibility analysis is done by doing fuel cost analysis of two cases, i.e., simple hybrid vehicle and hybrid vehicle equipped with solar module and increased battery energy storage capacity for a specific round trip distance between two cities, i.e., Rawalpindi and Islamabad in comparison with feasibility of third case, i.e., proposed solar electric car model. The solar module selection along with desired number of batteries with charging and discharging time and motor power required to carry five persons weight (70 kg each) is calculated for third case. Moreover, total carbon dioxide emission analysis has been carried out from car material production to its assembly, manufacturing solar module and nickel metal hydride battery for each case. The annual carbon dioxide emitted from fuel in first two cases relative to electric outlet in third case for specific distance has been analyzed. On large scale, emission analyses for hundred cars of each case have been done at 100 km distance. From calculations, it is revealed that overall emissions in third case on large scale and from its material production, assembly, solar module and batteries manufacturing perspective are comparatively less than other cases.     

3D geomechanical modeling and estimating the compaction and subsidence of Fahlian reservoir formation (X-field in SW of Iran)

A geomechanical model can reveal the mechanical behavior of rocks and be used to manage the reservoir programs in a better mode. Fluid pressure will be reduced during hydrocarbon production from a reservoir. This reduction of pressure will increase the effective stress due to overburden sediments and will cause porous media compaction and surface subsidence. In some oil fields, the compacting reservoir can support oil and gas production. However, the phenomena can also cause the loss of wells and reduced production and also cause irreparable damage to the surface structures and affect the surrounding environment. For a detailed study of the geomechanical behavior of a hydrocarbon field, a 3D numerical model to describe the reservoir geomechanical characteristics is essential. During this study, using available data and information, a coupled fluid flow-geomechanic model of Fahlian reservoir formation in X-field in SW of Iran was constructed to estimate the amount of land subsidence. According to the prepared model, in this field, the maximum amount of the vertical stress is 110 MPa and the maximum amount of the horizontal stress is 94 MPa. At last, this model is used for the prediction of reservoir compaction and subsidence of the surface. The maximum value of estimated ground subsidence in the study equals to 29 mm. It is considered that according to the obtained values of horizontal and vertical movement in the wall of different wells, those movements are not problematic for casing and well production and also the surrounding environment.     

Performance and environmental impact of a turbojet engine fueled by blends of biodiesels

Depletion of conventional fuels, concerns about environmental pollution and the tightening of exhaust emission legislations are the main reasons for increasing research on alternative fuels produced from agricultural feedstock. In this study, biodiesel fuels produced from cotton and corn vegetable oils are investigated as renewable fuels for a gas turbine engine for aviation. The biodiesel fuels are defined as cotton methyl ester (CTME) and corn methyl ester. The performance characteristics and exhaust emissions of the gas turbine engine are investigated when the engine fueled with three blends of 10%(B10), 20%(B20) and 50%(B50) of biodiesel/JetA-1 by volume. The biodiesel fuels were produced using transesterification process and characterized according to ASTM biodiesel specifications. Chemical and physical properties show a real potential of using biodiesel blends as an alternative for JetA-1. The measured engine performance parameters and exhaust emissions are compared with that of pure JetA-1 over a range of throttle setting. The gas turbine engine used in this study is equipped with pressure, flow, temperature, thrust and speed sensors that connected to data acquisition system and control unit in addition to exhaust gas analyzer. The experimental results show that biodiesel fuels can be used up to blend of 50% with JetA-1 in gas turbine engines with slight enhancement in engine performance and significant improvements in exhaust emissions. The engine static thrust is increased with 2% for B50 at lower and medium engine speeds and decreased with 11% at high engine speed compared to conventional JetA-1 fuel. The thrust-specific fuel consumption for biodiesel blends is lower than that for regular JetA-1 fuel. The gas turbine engine efficiency is increased for biodiesel blends by 14% compared to JetA-1, and this is reported for CTME B50. For oxygen concentration in exhaust gases emissions, the higher the biodiesel blend, the higher the O₂ concentration in the exhaust compared with JetA-1 fuel. The O₂ level increased by 6% for biodiesel blend of B50 compared to JetA-1 fuel. The emissions of CO and HC emissions decreased by 5 and 37%, respectively, compared with conventional JetA-1. Additionally, the biodiesel blends achieve a higher CO₂ and NO_x emissions with 11 and 27%, respectively, compared to JetA-1. The sulfur dioxide SO₂ decreased by 75% compared to the regular JetA-1 fuel.     

Organic Material and Trace Elements of Bituminous Rocks in the Ozankiiy Field, Ankara, Turkey

Bituminous rocks in the Ozankoey （Ankara） field are different from those of the Paleocene- Eocene Mengen and Giineytepe （Bolu） regions in metal enrichment levels. Organic carbon （Corg） content of organic material-rich rocks in the Ozankoey （Ankara） field is 3.66-40.72% wt averaging 14.34%. The dominant organic materials are algae/amorphous accompanied by minor amount of herbaceous material （The dominant kerogen type is Type-I with a limited amount of Type-Ⅱ kerogen.）. The bituminous rocks in the Ozankoey field are enriched in heavy metals such as Ni, Mn, As and Cr. In comparison with the average enrichment values of dements, Ni, Mn, As and Cr in bituminous shales of the Ozankoey field are as about 4.38, 14.93, 10.90 and 5.58 times as average values. The average concentrations of these heavy metals are also as high as 215× 10^-6, 828 × 10^-6, 58.54 × 10^-6, and 148 × 10^-6 respectively. In addition, sorption properties of day and organic materials are also important for metal enrichments in the bituminous shales.     

Interfacial instability of sand patterns induced by turbulent shear flow

When a turbulent shear flow above a plane sand surface entrains sand grains,it generates a variety of sand patterns.Fluvial sand forms two major interfacial patterns:meso-scale dunes and antidunes,and large-scale bars.Measurements have evidenced that under erosive conditions,meso-scale patterns either change to or coexist with large-scale patterns.However,it remains elusive what exactly drives the switching of interfacial patterns and how the switching occurs.Here,we showdcombing a flow model with a grain transport model,allowing for both the surface and suspended sand fluxes dthat the switching of patterns emerges from the shear-driven complex feedback between grain transport and topographic perturbations.The switching predominantly depends on the magnitudes of the Rouse number and the grain size to undisturbed flow depth ratio.The model offers quantitative predictions of the maximum amplification of sand patterns and unveils a new attraction erepulsion phenomenon.     

Sediment settling in the Latian Dam in Iran

Among the difficulties that influence future dam operations,reservoir sedimentation is the most problematic for engineers.This study predicted the amount and pattern of sedimentation for use in estimation of the useful lifespan of reservoirs and identification of optimal locations for outlets and intakes at the initial stages of dam design.Hydrographic surveys of different dams can provide better insight into this phenomenon.Latian Dam in Iran has conducted hydrographic surveys during 7 time periods.The amount and process of sedimentation in this reservoir were determined,and predictions of distribution of sediments were validated by well-known,common methods.The formation of a delta in the reservoir was investigated for different time periods after operation.Future problems due to the impacts of sedimentation on dam operation and the useful lifespan of the reservoir were predicted.In addition,the study results may be used for developing empirical methods to predict sedimentation patterns in other reservoirs.     

The added value of joint PP–PS inversion for reservoir characterization: A case study using Jubarte PRM seismic data (offshore Brazil)

The added value of the joint pre-stack inversion of PP (incident P-wave and reflected P-wave) and PS (incident P-wave and reflected S-wave) seismic data for the time-lapse application is shown. We focus on the application of this technique to the time-lapse (four-dimensional) multicomponent Jubarte field permanent reservoir monitoring seismic data. The joint inversion results are less sensitive to noise in the input data and show a better match with the rock physics models calibrated for the field. Further, joint inversion improves S-impedance estimates and provides a more robust quantitative interpretation, allowing enhanced differentiation between pore pressure and fluid saturation changes, which will be extremely useful for reservoir management. Small changes in reservoir properties are expected in the short time between the time-lapse seismic acquisitions used in the Jubarte project (only 1 year apart). The attempt to recover subtle fourth-dimensional effects via elastic inversion is recurrent in reservoir characterization projects, either due to the small sensitivity of the reservoirs to fluid and pressure changes or the short interval between the acquisitions. Therefore, looking for methodologies that minimize the uncertainty of fourth-dimensional inversion outputs is of fundamental importance. Here, we also show the differences between PP only and joint PP–PS inversion workflows and parameterizations that can be applied in other projects. We show the impact of using multicomponent data as input for elastic seismic inversions in the analysis of the time-lapse differences of the elastic properties. The larger investment in the acquisition and processing of multicomponent seismic data is shown to be justified by the improved results from the fourth-dimensional joint inversion.