海洋纤维增强热塑性立管极限承载拉力预测方法

海洋新型纤维增强热塑性立管因其可盘卷、耐腐蚀、耐疲劳和轻质化等优点,在深水油气开发中应用前景十分广阔。热塑性立管具有复合材料的各向异性、受力耦合效应及复杂的本构关系,且承受浮体运动和复杂海洋环境载荷,其失效模式尚未明确。针对轴对称载荷作用下纤维增强热塑性立管极限承载力问题,进行热塑性管稳态热传导和热应力的理论推导,求解了稳态温度和应力分布,首次给出了在任意温度载荷作用下管体径向位移的解析解,并直接求解其径向、轴向、环向和剪切应力。采用各向同性层Von Mises和各向异性层最大应力（Max Stress）准则或Tsai-Hill准则判定热塑性管的失效,基于应力分布、失效准则和二分法计算了热塑性管的极限载荷。温度载荷、纤维铺设角度和径厚比对管道的应力分布影响显著。不同温度载荷会改变失效指数沿径向的变化趋势,增大轴向拉力将增大热塑性管的失效指数,选用不同的失效准则在管体失效判定上存在一定的差异。热塑性管温度越低、纤维铺设角越小及径厚比越大,管道对轴向拉伸载荷的承载能力越强。     

内蒙古维拉斯托锡多金属矿石英脉形态分带定量分析

为探讨维拉斯托锡多金属矿床含锡石英脉形态分带的成矿动力学机制,通过利用分形和混合分布工具对断层脉带和上、下节理脉带进行定量分析。上、下节理脉带在脉厚、钨锡品位分形维数和混合筛分分布方面均具有相似性,暗示了两者可能具有相似的成矿机制。与上、下节理脉带相比,断层脉带的脉厚和钨锡品位分形维数均较小,断层脉带内的聚焦化流动、较低的脉体成核率、脉体叠加生长和矿化叠加富集可能是导致断层脉带的厚脉和富矿比例均高于上、下节理脉带的重要原因。     

Regional debris flow susceptibility analysis based on principal component analysis and self-organizing map: a case study in Southwest China

A method was developed to analyze the susceptibilities of 541 regional basins affected by debris flows at the Wudongde Dam site in southwest China. Determining susceptibility requires information on source material quantity and occurrence frequency. However, the large number of debris flows can hinder the individual field investigation in a each small basin. Factors that may trigger debris flows can be identified using remotely sensed interpretation information. Susceptibility analysis can then be conducted based on these factors. In this study, SPOT5 satellite imagery, digital elevation models (DEM), a lithology distribution map, and rainfall monitoring data were used to identify 12 debris flow trigger factors: basin relief ratio, slope gradient in the initiation zone, drainage density, downslope curvature of the main channel, vegetation coverage, main channel aspect, topographic wetness index, Melton’s ruggedness number, lithology, annual rainfall, form factor, and cross-slope curvature of the transportation zone. Principal component analysis was used to obtain the eight principal components of these factors that contribute to susceptibility results. Then, a self-organizing map method was adopted to analyze the principal components, which resulted in a debris flow susceptibility classification. Field validation of 26 debris flow basins was used to evaluate the errors of the susceptibility classification, as well as assess the causes of such errors. The study found that principle component analysis and self-organizing map methodologies are good predictors of basin susceptibility to debris flows.     

An approach to determination of phenolic compounds in seawater using SPME-GC-MS based on SWCNTs coating

Phenolic compounds have become one kind of the important pollutants of the marine environment. Single-walled Carbon nanotubes, as one-dimensional nano materials, have light weight and perfect hexagonal structure of connections, with many unusual mechanical, chemical and electrical properties. In recent years, with the research of carbon nanotubes and other nano materials, the application prospect is also constantly discussed. In this paper, homemade single-walled carbon nanotubes(SWCNTs) coating was used for establishing an analytical approach to the determination of five kinds of phenolic compounds in seawater using SPME-GC-MS. Optimal conditions: After saturation was conducted with Na Cl, and p H was adjusted to 2.0 with H_2SO_4, the extract was immersed in a water bath at 40 for GC℃-MS determination through 40-min agitating extraction at 500 rmin~(-1) and 3-min desorption at 280℃. The liniearities ranged between 0.01-100 μg L~(-1), and the determination limits ranged between 1.5-10 ngL~(-1). The relative standard deviation(RSD, n = 5) was less than 6.5%. For the phenolic compounds obtained from the spiked recovery test for actual seawater samples, the rates of recovery were 87.5%-101.7%, and the RSDs were less than 8.8%, which met the requirements of determination. Due to its simplicity, high efficiency and low consumption, this approach is suitable for the analysis of trace amounts of phenolic compounds in marine waters.     

Accessing effects and signals of leakage from a CO<Subscript>2</Subscript> reservoir to a shallow freshwater aquifer by reactive transport modelling

CO₂ geological storage is a transitional technology for the mitigation of climate change. In the vicinity of potential CO₂ reservoirs in Hungary, protected freshwater aquifers used for drinking water supplies exist. Effects of disaster events of CO₂ escape and brine displacement to one of these aquifers have been studied by kinetic 1D reactive transport modelling in PHREEQC. Besides verifying that ion concentrations in the freshwater may increase up to drinking water limit values in both scenarios (CO₂ or brine leakage), total porosity of the rock is estimated. Pore volume is expected to increase at the entry point of CO₂ and to decrease at further distances, whereas it shows minor increase along the flow path for the effect of brine inflow. Additionally, electrical conductivity of water is estimated and suggested to be the best parameter to measure for cost-effective monitoring of both worst-case leakage scenarios.     

Apatite-hosted melt inclusions from the Panzhihua gabbroic-layered intrusion associated with a giant Fe–Ti oxide deposit in SW China: insights for magma unmixing within a crystal mush

The ～?2-km-thick Panzhihua gabbroic-layered intrusion in SW China is unusual because it hosts a giant Fe–Ti oxide deposit in its lower zone. The deposit consists of laterally extensive net-textured and massive Fe–Ti oxide ore layers, the thickest of which is ～?60 m. To examine the magmatic processes that resulted in the Fe enrichment of parental high-Ti basaltic magma and the formation of thick, Fe–Ti oxide ore layers, we carried out a detailed study of melt inclusions in apatite from a ～?500-m-thick profile of apatite-bearing leucogabbro in the middle zone of the intrusion. The apatite-hosted melt inclusions are light to dark brown in color and appear as polygonal, rounded, oval and negative crystal shapes, which range from ～?5 to ～?50 µm in width and from ～?5 to ～?100 µm in length. They have highly variable compositions and show a large and continuous range of SiO₂ and FeO_t with contrasting end-members; one end-member being Fe-rich and Si-poor (40.2 wt% FeO_t and 17.7 wt% SiO₂) and the other being Si-rich and Fe-poor (74.0 wt% SiO₂ and 1.20 wt% FeO_t). This range in composition may be attributed to entrapment of the melt inclusions over a range of temperature and may reflect the presence of µm-scale and immiscible Fe-rich and Si-rich components in different proportions. Simulating results for the motion of Si-rich droplets within a crystal mush indicate that Si-rich droplets would be separated from Fe-rich melt and migrate upward due to density differences in the interstitial liquid when the magma unmixed. Migration of the Si-rich, immiscible liquid component from the interstitial liquid caused the remaining Fe-rich melt in the lower part to react with plagioclase primocrysts (An_59–60), as evidenced by fine-grained lamellar intergrowth of An-rich plagioclase (An_79–84)?+?clinopyroxene in the oxide gabbro of the lower zone. Therefore, magma unmixing within a crystal mush, combined with gravitationally driven loss of the Si-rich component, resulted in the formation of Fe-rich, melagabbro and major Fe–Ti oxide ores in the lower part and Si-rich, leucogabbro in the upper part of the intrusion.     

Dynamic Response and Mechanical Behaviours of Geogrid for High Earth-rockfill Dams

Geotechnical and Geological Engineering - Due to the complexity of the interaction between the geogrid and the soil interface in high earth-rock dams, the method of replacing the grid with steel...