Trace Metal Solid State Speciation in Aerosols of the Northern Levantine Basin,East Mediterranean

An established three stage sequential leach scheme was applied to a series of selected high volume aerosol samples (n = 35) collected from the Turkish Eastern Mediterranean coastline (Erdemli). Samples were selected according to their air mass back trajectory history to reflect the contrasting mixtures of aerosol material present in the Eastern Mediterranean marine aerosol. Two populations were adopted, those samples which were classed as “anthropogenic” and those which were “Saharan” dominated aerosol populations. Applying the three stage leach it was possible to define the proportion for each of the considered metals (Al, Fe, Cu, Pb, Cd, Zn and Mn) present in the (a) “exchangeable” (b) “carbonate / oxide” and (c) “refractory” phases, representing novel solid state aerosol speciation data for this marine system. Clear trends were established, conforming with data from previous studies with mainly crustal derived metals (Al and Fe) being present in the refractory phases (Al > 88%; Fe > 84%) and those influenced by anthropogenic sources being dominating in the exchangeable phase, although for these metals the variability was comparatively high (12–64%; 19–85%; 40–100% for Zn, Pb and Cd, respectively). For the majority, greater exchangeable fractions were present the lower the crustal source contribution to the aerosol population, whereas the “refractory” fraction exhibited contrasting behaviour. This was illustrated by the novel application of the mixing diagram, presenting each of the three speciation stages against the corresponding percent anthropogenic contribution to each collected sample. Zn, Pb and Cd all illustrated progressive decrease in the percent exchangeable with increasing crustal contribution to the aerosol population. The percent exchangeable was discussed in terms of its use to represent the upper limit of the bioavailable fraction of metal associated with the aerosol, post deposition. The mixing diagram approach enabled the prediction of the residual fractions for Cd, Pb and Zn (41 ± 4%; 62 ± 4% and 82 ± 5%, respectively,) in Saharan end-member material.     

Are Urban-Canopy Velocity Profiles Exponential?

Using analyses of data from extant direct numerical simulations and large-eddy simulations of boundary-layer and channel flows over and within urban-type canopies, sectional drag forces, Reynolds and dispersive shear stresses are examined for a range of roughness densities. Using the spatially-averaged mean velocity profiles these quantities allow deduction of the canopy mixing length and sectional drag coefficient. It is shown that the common assumptions about the behaviour of these quantities, needed to produce an analytical model for the canopy velocity profile, are usually invalid, in contrast to what is found in typical vegetative (e.g. forest) canopies. The consequence is that an exponential shape of the spatially-averaged mean velocity profile within the canopy cannot normally be expected, as indeed the data demonstrate. Nonetheless, recent canopy models that allow prediction of the roughness length appropriate for the inertial layer’s logarithmic profile above the canopy do not seem to depend crucially on their (invalid) assumption of an exponential profile within the canopy.     

Scaling of the Vertical Spreading of a Plume of a Passive Tracer in a Rough-Wall Neutral Boundary Layer

The influence of surface roughness on the dispersion of a passive scalar in a rough wall turbulent boundary layer has been studied using wind-tunnel experiments. The surface roughness was varied using different sizes of roughness elements, and different spacings between the elements. Vertical profiles of average concentration were measured at different distances downwind of the source, and the vertical spread of the plume was computed by fitting a double Gaussian profile to the data. An estimate of the integral length scale is derived from the turbulence characteristics of the boundary layer and is then used to scale the measured values of plume spread. This scaling reduces the variability in the data, confirming the validity of the model for the Lagrangian integral time scale, but does not remove it entirely. The scaled plume spreading shows significant differences from predictions of theoretical models both in the near and in the far field. In the region immediately downwind of the source this is due to the influence of the wake of the injector for which we have developed a simple model. In the far field we explain that the differences are mainly due to the absence of large-scale motions. Finally, further downwind of the source the scaled values of plume spread fall into two distinct groups. It is suggested that the difference between the two groups may be related to the lack of dynamical similarity between the boundary-layer flows for varying surface roughness or to biased estimates of the plume spread.     

Climatic regime shift and decadal anomalous events in China

Climatic time series from historical documents and instrumental records from China showed temporal and regional patterns in the last two to three centuries, including two multidecadal oscillations at quasi-20-year and quasi-70-year timescales revealed by signal analysis from wavelet transform. Climatic anomalous events on the decadal timescale were identified based on the two oscillations when their positive (or negative) phases coincide with each other to amplify amplitude. The coldest event occurred in the decade of 1965–1975 in eastern China, while the periods of 1920–1930, 1940–1950, and 1988–2000 appeared to be warmer in most parts of China. For the precipitation series in northern China, the dry anomalous event was found in the late 1920s, while the wet anomalous event occurred in the 1950s. A severe drought in 1927–1929 in northern China coincided with the anomalous warm and dry decade, caused large-scale famine in nine provinces over northern China. Climatic anomalous events with a warm-dry or cold-wet association in the physical climate system would potentially cause severe negative impacts on natural ecosystem in the key vulnerable region over northern China. The spatial pattern of summer rainfall anomalies in the eastern China monsoon region showed an opposite variations in phase between the Yellow River Valley (North China) and the mid-low Yangtze River Valley as well as accompanied the shift of the northernmost monsoon boundary. Climatic regime shifts for different time points in the last 200 years were identified. In North China, transitions from dry to wet periods occurred around 1800, 1875, and 1940 while the transitions from wet to dry periods appeared around 1840, 1910, and the late 1970s. The reversal transition in these time points can also be found in the lower Yangtze River. Climatic regime shifts in China were linked to the interaction of mid- and low latitude atmospheric circulations (the westerly flow and the monsoon flow) when they cross the Tibetan Plateau in East Asia.     

The influence of tropical Pacific forcing on the Arctic Oscillation

The potential role of tropical Pacific forcing in driving the seasonal variability of the Arctic Oscillation (AO) is explored using both observational data and a simple general circulation model (SGCM). A lead–lag regression technique is first applied to the monthly averaged sea surface temperature (SST) and the AO index. The AO maximum is found to be related to a negative SST anomaly over the tropical Pacific three months earlier. A singular value decomposition (SVD) analysis is then performed on the tropical Pacific SST and the sea level pressure (SLP) over the Northern Hemisphere. An AO-like atmospheric pattern and its associated SST appear as the second pair of SVD modes. Ensemble integrations are carried out with the SGCM to test the atmospheric response to different tropical Pacific forcings. The atmospheric response to the linear fit of the model’s empirical forcing associated with the SST variability in the second SVD modes strongly projects onto the AO. Idealized thermal forcings are then designed based on the regression of the seasonally averaged tropical Pacific precipitation against the AO index. Results indicate that forcing anomalies over the western tropical Pacific are more effective in generating an AO-like response while those over the eastern tropical Pacific tend to produce a Pacific-North American (PNA)-like response. The physical mechanisms responsible for the energy transport from the tropical Pacific to the extratropical North Atlantic are investigated using wave activity flux and vorticity forcing formalisms. The energy from the western tropical Pacific forcing tends to propagate zonally to the North Atlantic because of the jet stream waveguide effect while the transport of the energy from the eastern tropical Pacific forcing mostly concentrates over the PNA area. The linearized SGCM results show that nonlinear processes are involved in the generation of the forced AO-like pattern.     

Atmospheric chemistry of hydrogen fluoride

Although a large volume of monitoring and computer simulation data exist for global coverage of HF, study of HF in the troposphere is still limited to industry whose primary interest is the safety and risk assessment of HF release because it is a toxic gas. There is very limited information on atmospheric chemistry, emission sources, and the behavior of HF in the environment. We provide a comprehensive review on the atmospheric chemistry of HF, modeling the reactions and transport of HF in the atmosphere, the removal processes in the vertical layer immediately adjacent to the surface (up to approximately 500 m) and recommend research needed to improve our understanding of atmospheric chemistry of HF in the troposphere. The atmospheric chemistry, emissions, and surface boundary layer transport of hydrogen fluoride (HF) are summarized. Although HF is known to be chemically reactive and highly soluble, both factors affect transport and removal in the atmosphere, the chemistry can be ignored when the HF concentration is at a sufficiently low level (e.g., 10 ppmv). At a low concentration, the capability for HF to react in the atmosphere is diminished and therefore the species can be mathematically treated as inert during the transport. At a sufficiently high concentration of HF (e.g., kg/s release rate and thousands of ppm), however, HF can go through a series of rigorous chemical reactions including polymerization, depolymerization, and reaction with water to form molecular complex. As such, the HF species cannot be considered as inert because the reactions could intimately influence the plume’s thermodynamic properties affecting the changes in plume temperature and density. The atmospheric residence time of HF was found to be less than four (4) days, and deposition (i.e., atmosphere to surface transport) is the dominant mechanism that controls the removal of HF and its oligomers from the atmosphere. The literature data on HF dry deposition velocity was relatively high compared to many commonly found atmospheric species such as ozone, sulfur dioxide, nitrogen oxides, etc. The global average of wet deposition velocity of HF was found to be zero based on one literature source. Uptake of HF by rain drops is limited by the acidity of the rain drops, and atmospheric particulate matter contributes negligibly to HF uptake. Finally, given that the reactivity of HF at a high release rate and elevated mole concentration cannot be ignored, it is important to incorporate the reaction chemistry in the near-field dispersion close to the proximity of the release source, and to incorporate the deposition mechanism in the far-field dispersion away from the release source. In other words, a hybrid computational scheme may be needed to address transport and atmospheric chemistry of HF in a range of applications. The model uncertainty will be limited by the precision of boundary layer parameterization and ability to accurately model the atmospheric turbulence.     

Spatially explicit modelling of the impact of climate changes on pasture production in the North Island,New Zealand

To assess the potential impact of climate changes on pasture production in the North Island, New Zealand, eight climate scenarios of increased temperature and increased (or decreased) rainfall were investigated by integrating a polynomial regression model for pasture production with a Geographic Information System (GIS). The results indicated that the climate change scenarios assuming an increase in temperature by 1–2°C and a rainfall change by −20 to +20% would have a very significant impact on pasture production with a predicted pasture production variation from −46.2 to +51.9% compared with the normal climate from 1961–1990. Increased temperature would generally have a positive effect on pasture production in the south and southeast of the North Island, and increased rainfall would have a positive effect in the central, south and southeast of the North Island and a negative effect in the north of the North Island. The interaction of decreased rainfall and increased temperature would have a negative impact for the whole North Island except some central areas with high rainfall. Relevant management practices for coping with potential climate change are discussed.     

The Impact of Land-Surface Parameter Properties and Resolution on the Simulated Cloud-Topped Atmospheric Boundary Layer

A method to simulate characteristics of wind speed in the boundary layer of tropical cyclones in an idealized manner is developed and evaluated. The method can be used in a single-column modelling set-up with a planetary boundary-layer parametrization, or within large-eddy simulations (LES). The key step is to include terms in the horizontal velocity equations representing advection and centrifugal acceleration in tropical cyclones that occurs on scales larger than the domain size. Compared to other recently developed methods, which require two input parameters (a reference wind speed, and radius from the centre of a tropical cyclone) this new method also requires a third input parameter: the radial gradient of reference wind speed. With the new method, simulated wind profiles are similar to composite profiles from dropsonde observations; in contrast, a classic Ekman-type method tends to overpredict inflow-layer depth and magnitude, and two recently developed methods for tropical cyclone environments tend to overpredict near-surface wind speed. When used in LES, the new technique produces vertical profiles of total turbulent stress and estimated eddy viscosity that are similar to values determined from low-level aircraft flights in tropical cyclones. Temporal spectra from LES produce an inertial subrange for frequencies \(\gtrsim \)0.1 Hz, but only when the horizontal grid spacing \(\lesssim \)20 m.     

An approach to adaptation to climate changes in Poland

Adopted by COP 10 (Dec 1/CP.10) and approved by the MOP1, the Buenos Aires programme of adaptation and response measures opens doors to intensify preparations for expected climate change. By this decision the COP, requested the SBSTA to develop a structured 5-year programme of work of the SBSTA on the scientific, technical and socio-economic aspects of impacts of, and vulnerability and adaptation to, climate change. Consequently, the COP, by its decision 2/CP.11, adopted the “Five-year programme of work of the Subsidiary Body for Scientific and Technological Advice on impacts, vulnerability and adaptation to climate change” Finally during COP12 this programme was approved as “Nairobi Work Programme on impacts, vulnerability and adaptation to climate change”. This programme has fundamental significance not only for developing countries, but also for industrialized nations in which some sectors of the or social life are particularly vulnerable to climate change, specifically, inter alia EIT countries and new EU Member States. Further development of this adaptation programme economy should contain steps that provide optimum economic and social effectiveness, risk management, identification of vulnerable sectors and gaps in knowledge, preparation of a list of policy options, including an analysis of cost effectiveness, selection of the most effective policies, and a preparedness implementation plan. In Poland the preliminary adaptation programme covered agriculture, water management, and coastal zone management. For the time being, gaps in knowledge and preparedness measures have been identified. An estimation of possible impact on these areas was based on chosen GCMs, and sea level rise IPCC scenarios. In conclusion, it was stated that the results achieved should be seen as a first step forward and a more comprehensive study is necessary to update the results and cover other sectors of the economy, such as health protection, spatial planning, ecosystems and forestry, and to develop specific guidelines and recommendations for policy-makers.     

Multi-Source Emission Determination Using an Inverse-Dispersion Technique

Inverse-dispersion calculations can be used to infer atmospheric emission rates through a combination of downwind gas concentrations and dispersion model predictions. With multiple concentration sensors downwind of a compound source (whose component positions are known) it is possible to calculate the component emissions. With this in mind, a field experiment was conducted to examine the feasibility of such multi-source inferences, using four synthetic area sources and eight concentration sensors arranged in different configurations. Multi-source problems tend to be mathematically ill-conditioned, as expressed by the condition number κ. In our most successful configuration (average κ = 4.2) the total emissions from all sources were deduced to within 10% on average, while component emissions were deduced to within 50%. In our least successful configuration (average κ = 91) the total emissions were calculated to within only 50%, and component calculations were highly inaccurate. Our study indicates that the most accurate multi-source inferences will occur if each sensor is influenced by only a single source. A “progressive” layout is the next best: one sensor is positioned to “see” only one source, the next sensor is placed to see the first source and another, a third sensor is placed to see the previous two plus a third, and so on. When it is not possible to isolate any sources κ is large and the accuracy of a multi-source inference is doubtful.