Detection of crustal motion using spaceborne laser ranging systems

The spaceborne laser ranging (or lasering) system provides a method of precise positioning of a large number of points on the earth's surface in a short period of time. That is, a measure of the relative location of geodetic markers from a space platform can maintain horizontal and vertical control to 2 to 5 cm. At this level of control, small earth surface crustal motions should be detectable. Development of a model for the strain field can be constructed. Furthermore, the spaceborne lasering system can survey an area in a very short period of time (one to two weeks) and resurvey the area as required. System design parameters are now being established by NASA for a possible test flight aboard the Shuttle in 1982. These include design specifications of economical corner cubes for ground retroreflectors coupled with the evolution of engineering model to flight model development. If the experiment of the Shuttle proves to be successful, it is hoped to put the laser in a free flight satellite. This paper presents the results of a simulated analysis for this latter case. The system is conceived as an orbiting ranging device with a ground base grid of reflectors or transponders (spacing 10 to 30 km), which are projected to be of low cost (maintenance-free and unattended) and which will permit the saturation of a local area to obtain data useful to monitor crustal movements. The test network includes 75 stations with roughly half of them on either side of the San Andreas fault zone. Critical study comparatively evaluates various observational schemes and statistically analyzed crustal motion recovery. The study considers laser radar as the main ranging system pending final selection from many possible candidates. The satellite orbit is inclined at 110° and slightly eccentric (e=0.04) with orbital altitudes varying from 370 km to 930 km. The results indicate that the geometric mode (simultaneous ranging) with a minimum of five grid and three distant (fundamental) stations and mixed ranging to satellite and airplane seems to be most promising. The fundamental stations are distinguished from the grid station in their location and this location should be “distant” enough from the area of crustal movement so that they can be considered stationary over the time span of the motion involved. Presented at the 1977 I.A.G. International Symposia on Satellite Geodesy, Budapest, Hungary, June 28–July 1, and on Recent Crustal Movements, Palo Alto, California, USA, July 25–30.     

Multiple statistical approaches for the discrimination of mangrove species of Rhizophoraceae using transformed field and laboratory hyperspectral data

This study aims at discriminating eight mangrove species of Rhizophoraceae family of Indian east coast using field and laboratory spectra in spectral range (350–2500 nm). Parametric and non-parametric statistical analyses were applied on spectral data in four spectral modes: (i) reflectance (ii) continuum removed, (iii) additive inverse and (iv) continuum removed additive inverse. We introduced continuum removal of inverse spectra to utilize the advantage of continuum removal in reflectance region. Non-parametric test gave better separability than parametric test. Principal component analysis and stepwise discriminant analysis were applied for feature reduction and to identify optimal wavelengths for species discrimination. To quantify the separability, Jeffries–Matusita distance measure was derived. Green (550 nm), red edge (680–720 nm) and water absorption region (1470 and 1850 nm) were found to be optimal wavelengths for species discrimination. The continuum removal of additive inverse spectra gave better separability than the continuum removed spectra.     

Nine years of GPS measurements of crustal deformation at Imphal,Indo-Burmese wedge

We report results of 9 years of GPS measurements of crustal deformation at Imphal, Manipur, a site located in the Indo-Burmese wedge of northwest Sunda arc. The analysis of these measurements suggests that the site moves at a rate of about 36.3±0.5 mm/year towards N55° in the ITRF2008. With respect to the Indian plate it moves at a rate of 16.7 mm/year towards N222°, i.e., predominantly towards southwest. The site is located about 15 km east of the Churachandpur Mao fault (CMF), which is reported to accommodate part of the India-Sunda motion. The site motion is not significantly affected by the earthquakes that occurred in the nearby region. However, the 2004 Sumatra-Andaman earthquake caused a coseismic displacement of ～ 3–5 mm predominantly towards southwest. The site motion is almost linear, with some seasonal variation, and does not show any evidence of accelerated slip or slow earthquake on the CMF or along the plate boundary.     

Mangrove sediments a sink for heavy metals? An assessment of Muthupet mangroves of Tamil Nadu,southeast coast of India

Mangrove forests are one of the most productive and biodiverse wetlands on earth. Yet, these unique coastal tropical forests are among the most threatened habitats in the world. Muthupet mangroves situated in the southeastern coast of India, has a reverse “L” shaped structure. Four cores were collected in 2008, sliced and subsampled at 2.5 cm length. The heavy metals (Mn, Cu, Zn, Ni, Pb, Cr, Cd) and other associated geochemical parameters were evaluated to determine pollution history of Muthupet. An evaluation of the status of heavy metal pollution through the index analysis approach was attempted by computing geoaccumulation index, anthropogenic factor, enrichment factor, contamination factor and degree of contamination, pollution load index and metal pollution index. To compensate for the natural variability of heavy metals in the core sediments, normalization using Al was carried out so that, any anthropogenic metal contributions may be detected and quantified. Results of the study reveal that significant metal contamination exists, and all the metals are found to be higher than continental crustal values. The fine sediments of Muthupet vary between uncontaminated and moderately contaminated with almost no enrichment (EF < 1) to severe enrichment (EF > 10). On comparison, the core collected close to aquafarms and dense mangrove forest (C3) is the most polluted core and the core retrieved where minor rivers drain (C2) is the least polluted.     

Hydrogeochemical investigation and groundwater quality assessment of Pratapgarh district,Uttar Pradesh

Hydogrochemical investigation of groundwater resources of Paragraph district has been carried out to assess the solute acquisition processes and water quality for domestic and irrigation uses. Fifty-five groundwater samples were collected and analyzed for pH, electrical conductivity, total dissolved solids, hardness, major anions (F^?, Cl^?, NO₃, HCO₃ ^?, SO₄ ^2?) and cations (Ca²⁺, Mg²⁺, Na⁺, K⁺). Study results reveal that groundwater of the area is alkaline in nature and HCO₃ ^?, Cl^?, Mg²⁺, Na⁺ and Ca²⁺ are the major contributing ions to the dissolved solids. The hydrogeochemical data suggest that weathering of rock forming minerals along with secondary contributions from agricultural and anthropogenic sources are mainly controlling the groundwater composition of Pratapgarh district. Alkaline earth metals (Ca²⁺+Mg²⁺) exceed alkalis (Na⁺+K⁺) and weak acid (HCO₃ ^?) dominate over strong acids (Cl^?+SO₄ ^2?) in majority of the groundwater samples. Ca-Mg-HCO₃ and Ca-Mg-Cl-HCO₃ are the dominant hydrogeochemical facies in the groundwater of the area. The computed saturation indices demonstrate oversaturated condition with respect to dolomite and calcite and undersaturated with gypsum and fluorite. A comparison of groundwater quality parameters in relation to specified limits for drinking water shows that concentrations of TDS, F^?, NO₃ ^? and total hardness exceed the desirable limits in many water samples. Quality assessment for irrigation uses reveal that the groundwater is good for irrigation. However, values of salinity, sodium adsorption ratio (SAR), residual sodium carbonate (RSC), %Na and Kelley index are exceeding the prescribed limit at some sites, demanding adequate drainage and water management plan for the area.     

Avalanche hazard mitigation in east Karakoram mountains

Natural Hazards - Karakoram mountains range in north-western part of Himalayas is about 500&nbsp;km in length and hosts some of the world’s highest peaks and longest glaciers. It is...     

Lake bank filtration at Nainital,India: water-quality evaluation

There are different water-supply schemes in Uttarakhand, India to tap the water from streams, rivers and lakes. At Nainital, seven tube-wells (depths 22.6–36.7 m), located at a distance of <100 m from the lake, are being used to abstract (1) lake water after passage through the soil and (2) subsurface water/groundwater flowing towards the lake. Water samples from the lake and tube-wells were analyzed in monsoon and non-monsoon periods from 1997 to 2006. Total dissolved solids, EC, alkalinity and hardness were found to be marginally greater in tube-well waters. The difference in hydrochemistry of tube-well water was mainly due to variation in flow regimes during monsoon and non-monsoon periods. Results clearly indicate that lake water as such is not potable as it contains unacceptable levels of organic matter in terms of COD (~44 mg/L), coliforms (~15.6 × 10⁴ MPN/100 mL) and nutrients. Coliform bacteria and COD have not been detected in any of the tube-well water samples over the years. Lake water, treated by sand filters did not conform to drinking water standards. These investigations have led to the closure of the treatment facility and installation of two tube-wells in addition to the existing five tube-wells.

---

Résumé  Il existe divers projets d’alimentation en eau dans l’état d’Uttarakhand, Inde, afin de capter l’eau de ruisseaux, de rivières et de lacs. A Nainital, sept puits tubés (profondeur de 22.6–36.7 m), situés à une distance < à 100 m du lac, sont utilisés pour prélever (1) de l’eau du lac après transit à travers le sol et (2) de l’eau de sub-surface/eau souterraine s’écoulant vers le lac. Des échantillons d’eau du lac et des puits tubés ont été analysés en périodes de mousson et de celles sans mousson 1997 à 2006. Résidu sec, C.E., alcalinité et dureté ont été trouvés marginalement supérieurs dans l’eau des puits tubés. La différence d’hydrochimie de l’eau des puits tubés était surtout due à la variation des régimes d’écoulement pendant les périodes de mousson et de celles sans mousson. Les résultats indiquent clairement que l’eau du lac en tant que telle n’est pas potable car elle contient des teneurs inacceptables de matière organique en termes de COD (~44 mg/L), de coliformes (~15.6 × 10⁴ MPN/100 mL) et d’éléments nutritifs. Des bactéries coliformes et du COD n’ont été détectés dans aucun des échantillons d’eau de puits tubés au fil des années. L’eau du lac traitée par des filtres à sable ne se conformait pas aux normes de l’eau potable. Ces recherches ont conduit à la fermeture de l’installation de traitement et à l’implantation de deux puits tubés en plus des cinq puits existants.

---

Resumen  En el estado de Uttarakhand, India, existen diferentes esquemas de abastecimiento de agua que explotan agua de arroyos, ríos y lagos. En Nainital, siete pozos (profundidades entre 22.6–36.7 m), ubicados a una distancia de <100 m del lago, se usan para extraer (1) agua del lago luego de su pasaje a través del suelo y (2) agua superficial y subterránea que fluye hacia el lago. En períodos de monzón y de no monzón de 1997 a 2006 se han analizado muestras de agua del lago y de las captaciones. Se halló que el agua de los pozos es ligeramente mayor en términos del total de sólidos disueltos, la conductividad eléctrica, la alcalinidad y la dureza. La diferencia en la hidroquímica del agua de las perforaciones se debe principalmente a la variación de los regímenes de flujo durante los períodos de monzón y de no monzón. Los resultados claramente indican que el agua del lago no es potable por su contenido inaceptable de materia orgánica medida como demanda de carbono orgánico/oxígeno –DCO- (~44 mg/L), coliformes (~15.6 × 10⁴ NMP/100 mL) y nutrientes. En el período, no se han detectado bacterias coliformes ni DCO en las muestras de agua de las captaciones. El agua del lago, tratada con filtros de arena, no conformó los estándares de agua para bebida. Estas investigaciones han demostrado la necesidad de clausurar las instalaciones de tratamiento y la adición de dos captaciones a las cinco ya existentes.

     

An automated 3D modeling of topological indoor navigation network

Indoor navigation is important for various applications such as disaster management, building modeling, safety analysis etc. In the last decade, indoor environment has been a focus of wide research that includes development of indoor data acquisition techniques, 3D data modeling and indoor navigation. In this research, an automated method for 3D modeling of indoor navigation network has been presented. 3D indoor navigation modeling requires a valid 3D model that can be represented as a cell complex: a model without any gap or intersection such that two cells (e.g. room, corridor) perfectly touch each other. This research investigates an automated method for 3D modeling of indoor navigation network using a geometrical model of indoor building environment. In order to reduce time and cost of surveying process, Trimble LaserAce 1000 laser rangefinder was used to acquire indoor building data which led to the acquisition of an inaccurate geometry of building. The connection between surveying benchmarks was established using Delaunay triangulation. Dijkstra algorithm was used to find shortest path in between building floors. The modeling results were evaluated against an accurate geometry of indoor building environment which was acquired using highly-accurate Trimble M3 total station. This research intends to investigate and propose a novel method of topological navigation network modeling with a less accurate geometrical model to overcome the need of required an accurate geometrical model. To control the uncertainty of the calibration and of the reconstruction of the building from the measurements, interval analysis and homotopy continuation will be investigated in the near future.     

Hydrogeochemical assessment of surface and groundwater resources of Korba coalfield,Central India: environmental implications

The present study assesses the impact of coal mining on surface and groundwater resources of Korba Coalfield, Central India. Accordingly, water samples collected from various sources are analyzed for major ions, trace elements, and other mine effluent parameters. Results show that the groundwater samples are slightly acidic, whereas river water and mine water samples are mildly alkaline. Elevated concentrations of Ca²⁺, Na⁺, HCO₃ ^?, and SO₄ ^2? alongside the molar ratios (Ca²⁺+Mg²⁺)/(SO₄ ^2?+HCO₃ ^?) <1 and Na⁺/Cl^? >1 suggest that silicate weathering (water-rock interaction) coupled with ion exchange are dominant solute acquisition processes controlling the chemistry of groundwater in the study area. The overall hydrogeochemistry of the area is dominated by two major hydrogeochemical facies (i.e., Ca–Cl–SO₄ and Ca–HCO₃). Analysis of groundwater and river water quality index (GRWQI) elucidates that majority (82%) of samples are of “excellent” to “good” category, and the remaining 12% are of “poor” quality. Similarly, the effluent water quality index (EWQI) indicates that 6 out of 8 samples belong to excellent quality. Concentration of trace element constituents such as As, Zn, Cu, Cr, and Cd is found to be well within the stipulated limits for potable use, except for Fe, Mn, and Pb. Suitability of water samples for irrigation purpose, established using standard tools like Wilcox and USSL diagrams, reveal “excellent to permissible” category for majority of the samples. The present study also substantiates the effectiveness of the measures implemented for the treatment of mine effluent water.     

Strain distribution in superposed buckling folds and the problem of reorientation of early lineations

Two series of experiments were carried out with soft model-materials in order to assess the relative importance of initial homogeneous strain, external rotation and late-stage strain in reorienting early lineations during superposed buckle-folding. In the first series cylindrical buckling folds were produced in embedded planar sheets containing a “lineation”. In the second series noncylindrical folds were produced by compression of a set of cylindrical folds. The experiments indicate that the ratio of buckle shortening to layer-parallel strain is much smaller when the principal extension is parallel to the fold-axis than in the case when the principal extension is perpendicular to the fold-axis. In very competent rocks, the reorientation of old lineations is mainly by external rotation and by the associated concentric longitudinal strain. In moderately competent rocks, the orientation of early lineations always changes by initial homogeneous strain before buckling becomes significant. Because of the unlike amounts of initial strain in layers of different competences, orientations of unrolled lineations may not be parallel in disharmonically folded layers of unlike competences. Under certain conditions the early lineation may become virtually parallel to the later fold-axis. The experiments indicate that the effects of late-stage strain in buckle-folding are largely restricted to the incompetent layers of a multilayer. Hence, if orientation data of early lineations in both competent and incompetent rocks are lumped together, the pattern of orientation may become quite complex. Even for a single competent layer, the pattern of early lineations can locally become complex because of the complex nature of concentric longitudinal strain (and strain resulting from stretching of middle surface of the layer), development of conical folds, development of shear strain along hinge zones of deformed early folds and also because of the development of different orders of folds in both the first and the second deformations.