符合药用质量要求的甲壳素精制工艺

本文探讨了符合以下药用质量要求的甲壳素的精制工艺，甲壳素脱乙酰度在７０－９０％之间，钙的含量〈０．５％，总蛋含量在７－８％之间，灰分〈１％，酸不溶性灰分〈０．０５％，无毒，为甲壳素在医药上的应用，提供了生产数据。     

Measurement of the redox speciation of iron in seawater by catalytic cathodic stripping voltammetry

Catalytic cathodic stripping voltammetry (CSV) preceded by adsorptive collection of complexes of 1-nitroso-2-napthol (NN) can be used to determine iron in seawater. It is shown here that iron(II) is effectively masked in the presence of 2,2-dipyridyl (Dp) so that iron(III) is measured selectively. The concentration of iron(II) is then calculated as the difference between the concentrations of reactive iron (Fe_R) in the absence and presence of 2 μM Dp, Fe_R being defined as that which was complexed by 20 μM NN at pH 6.9 in the presence of 1.8 mM H₂O₂ and 5 ppm sodium dodecyl sulphate. A 30 min reaction time was allowed for Dp to react with iron(II) in seawater prior to the determination of reactive iron(III) using the same conditions as used for Fe_R. Detection limits of 0.08 nM, 0.077 nM and 0.12 nM were obtained for Fe_R, iron(III) and iron(II), respectively, using a 60 s deposition time.The method was utilised to determine the redox speciation of iron in the northern North Sea. Concentrations of Fe_R ranged between 0.8 and 3.5 nM with nutrient-like depth profiles. Iron(II) was found to be present at concentrations up to 1.2 nM, the highest concentrations occurring in the upper 20 m of the water column.     

Risk of dike failure due to flow slides

Flow slides may affect the stability of dikes. A flow slide is an instability of a submerged slope caused by liquefaction of loose, (medium) fine sand. Whether a flow slide will occur depends on the properties of the sand, which are a function of its density, and the geometry of the slope, as determined by wave and current induced scour and sedimentation. The influence of sand properties and the geometry parameters on the risk of flow slides are discussed. The application of a flow slide prediction method to an example and a risk analysis is briefly discussed.     

正压浅海湍流运动的雷诺应力封闭模型

根据湍流封闭理论,建立一种适用于正压浅海湍流运动的雷诺应力封闭模型(RSM),以代替目前三维浅海动力学模型中普遍采用的湍粘性系数的传统假设。通过直接建立并模化f—平面上正压海洋的雷诺应力传输方程,分别得到的微分形式和代数形式的RSM方程组。并讨论了进行数值计算所需要的边界条件。利用该模型可以进一步研究浅海潮流、风暴潮流及风海流等浅海流动的三维结构和湍流特性。     

A comparative study of some directional sea models

Current specification of the ocean wave environment for the design of offshore platforms does not adequately describe the directional nature of a real seaway. The strong wave frequency dependent nature of the directional behavior of observed seas is often over-simplified for design. A general formulation encompassing a wide range of directional sea models is presented. Parameter values used in some of the more popular directional sea models are examined. Approximate expressions for the two frequency dependent parameters in a modified Longuet-Higgins cosine wave spreading model are presented. A general procedure which allows an engineer to estimate parameters for alternate wave spreading models is discussed. To illustrate this procedure an empirically based modified cosine spreading model is used as the basis to estimate frequency dependent parameters for circular normal and wrapped Gaussian wave spreading models. A comparison of the contours of the various directional sea models and the prediction of the root-mean-square velocity distribution is presented.     

Wave drift enhancement effects in multi column structures

A theoretical assessment is made of mean wave drift forces on groups of vertical circular cylinders, such as the columns of a floating offshore platform. A complete analytical solution is obtained for two cylinders extending from seabed to free surface, and a long wave approximation is found to provide reliable predictions of the drift force in line with the waves at low frequencies. For moderate separation between the two cylinders, this force is found to tend at low frequencies to a value four times the force on an isolated cylinder.A numerical method is employed to study two surface piercing cylinders truncated below the free surface, and an arrangement of four vertical cylinders characteristic of a floating offshore platform. The mean vertical drift force is found to be reasonably well approximated, over the frequency range of practical interest, by the force on an individual cylinder considered in isolation multiplied by the number of cylinders in the group. Interaction effects, however, have a profound influence on the total horizontal drift force. At low frequencies this force is found to tend to the force on an isolated cylinder multiplied by the squate of the number of cylinders in the group.     

An experimental investigation of plunging breaker boundary layers in the transformation zone

Experimental investigation is made on the boundary layers of the transformation zone (i.e. the region between the last symmetrical wave profile depth and the breaking point) of plunging breakers propagating on a smooth beach with 1/12 uniform slope. Using a laser anemometer, the particle velocities are measured at four verticals along the transformation zone for three different steepnesses of waves within the plunging breaker range. The boundary layer flow in the transformation zone is found mostly of turbulent character and vertical distribution of particle velocities does not seem to conform to the classical law of the wall distribution given for steady-flow boundary layers. The results show that free-stream particle velocities, in the boundary layer of the breaker under the crest phase, increase considerably as the wave progresses towards the breaking point. The boundary layer thickness, defined as the velocity-affected region, remains constant throughout the transformation zone but it decreases with increasing deep-water wave steepness for the particular beach slope tested.     

Design of a caisson plate under wave impact

From the laboratory experiments and field studies it has been shown that when a wave breaks directly on a vertical wall, impact pressures of high magnitude and short duration, are produced. Despite the recent advances made in collecting data on impact pressure histories and their spatial distributions, analyses on the structural behaviour of the walls loaded by the impact forces do not seem adequate. In the present study the theoretical analysis of the response characteristics of a caisson plate, having different aspect ratios, under the wave impact loading is investigated. Numerical results for the dynamic values of moments and transverse displacements are obtained by the method of finite elements. Some prerequisite experimental data for wave breaking and resulting impact pressures are provided. The static results for moments and deflections are also computed for comparing them with the dynamic values. The dynamic results are found significantly greater than the static values. The ratio between the dynamic and static values is called “Dynamic magnification factor” that varies with plate aspect ratio. Based on this factor a procedure is proposed which may have practical consequences in the design of caisson plates.     

某船坞南翼墙基岩水下控制爆破技术

本文介绍的基岩水下爆破属临近重要建筑物的水下控制爆破。当岩石裂隙发育，且岩面有较厚的石碴覆盖层，其技术难度大，采取的诸如搭钢平台钻孔。塑料套管护孔，以及孔间、排间塑料导爆管雷管接力式微差起爆网路等措施，都是成功之经验，值得今后类似工程推广应用。     

The effect of currents on the generation of internal waves by a barotropic tide near an underwater ridge

In the frame of the linear theory for long waves, the paper studies long waves generated by a barotropic tide running at an arbitrary angle over a bottom ridge. The ocean is assumed to be two-layered. In the area of a ridge with a rectangular cross section, geostrophic flows are considered, coupled with the inclinations of the free surface and interface. Wave amplitudes are shown to depend on the angle of an onrunning tide and this allows us to reach a conclusion about the influence of a geostrophic current on the generation of internal waves. Translated by Vladimir A. Puchkin.