低周反复荷载下Q460钢材框架柱抗震性能分析

为了进一步完善Q460钢材在抗震设计规范中相关限值的要求,本文利用有限元软件ABAQUS,以轴压比、翼缘宽厚比、腹板高厚比和壁板宽厚比为变量,建立了共48根“工”字型框架柱和“箱”型框架柱,分析了其抗震性能。结果表明:翼缘宽厚比对框架柱的能量耗散系数影响较小;能量耗散系数随轴压比、腹板高厚比（“工”字型）和壁板宽厚比（“箱”型）增大而明显减小;框架柱的极限承载力随轴压比的减小及壁板宽厚比和翼缘宽厚比的增大而逐渐增大,当腹板高厚比接近规范限值时,承载力下降趋势明显增大。与采用Q235钢材的框架柱相比,Q460钢材框架柱的延性较小,仅为2左右;当采用Q460钢材时,“工”字型框架柱的极限位移角限值建议取为0.03,“箱”型框架柱的极限位移角限值建议取为0.032。规范中对翼缘宽厚比限值的规定偏于保守,其值最大可取至9。无论是“工”字型框架柱还是“箱”型框架柱,其腹板高厚比均不宜过大。Q460钢材框架柱的刚度退化率随轴压比的增大而增强,且翼缘宽厚比越大,腹板高厚比越小,柱的初始刚度越大,刚度退化程度越明显。     

热力强迫对台风次级环流的作用

本文利用无量纲的台风次级环流方程,用西太平洋地区11年的综合台风资料,计算了热力因子强迫的次级环流。通过计算,得到主要结论如下: 1.非绝热加热和积云热量垂直混合是主要的热力强迫因子,二者的作用具有同样量级。 2.热量的湍流涡旋通量及积云的热量水平输送作用都比较小。 3.Ekman抽吸与积云热量垂直混合是相互促进,共同发展的。有利于次级环流的增强。     

An Improved Approach for Parameterizing Surface-Layer Turbulent Transfer Coefficients in Numerical Models

Based on classic iterative computation results, new equations to calculate the surface turbulent transfer coefficients are proposed, which allow for large ratios of the momentum and heat roughness lengths. Compared to the Launiainen scheme, our proposed scheme generates results closer to classical iterative computations. Under unstable stratification, the relative error in the Launiainen scheme increases linearly with increasing instability, even exceeding 15%, while the relative error of the present scheme is always less than 8.5%. Under stable stratification, the Launiainen scheme uses two equations, one for 0 < Ri _B ≤ 0.08 and another for 0.08 < Ri _B ≤ 0.2, and does not consider the condition that Ri _B > 0.2, while its relative errors in the region 0 < Ri _B ≤ 0.2 exceed 31 and 24% for momentum and heat transfer coefficients, respectively. In contrast, the present scheme uses only one equation for 0 < Ri _B ≤ 0.2 and another equation for Ri _B > 0.2, and the relative error of the present scheme is always less than 14%.     

Test method for single interior right angle in a corner cube prism

1　ＩｎｔｒｏｄｕｃｔｉｏｎＴｈｅｃｏｒｎｅｒｃｕｂｅｐｒｉｓｍｏｒｒｅｔｒｏｒｅｆｌｅｃｔｏｒｉｓｅｘｔｅｎ ｓｉｖｅｌｙｕｓｅｄｉｎｐｌａｃｅｏｆｔｈｅｍｏｖａｂｌｅｍｉｒｒｏｒｉｎａｎｉｎ ｔｅｒｆｅｒｏｍｅｔｅｒ,ｏｒａｓａｃｏｏｐｅｒａｔｉｖｅｔａｒｇｅｔｉｎｒａｎｇｅｆｉｎｄｅｒ.Ｉｔｈａｓｔｈｒｅｅｓｕｒｆａｃｅｓ,ｗｈｉｃｈａｒｅｐｅｒｐｅｎｄｉｃ ｕｌａｒｔｏｅａｃｈｏｔｈｅｒａｎｄｃａｌｌｅｄｔｈｅｒｉｇｈｔａｎｇｕｌａｒｓｕｒ ｆａｃｅｓ.Ａｎｉｎｃｌｉｎｅｄｉｓｏｓｃｅｌｅｓｔｒ…     

Observational estimation of heat budgets on drifting ice and open water over the Arctic Ocean

It is of major scientific interests to determine the parameters of momentum, heat and vapor exchange in the planetary boundary layer in order to study the effects of ocean-ice-atmosphere interactions and their feedback mechanisms on global climate[1]. Lin…     

Primary dolostone related to the Cretaceous lacustrine hydrothermal sedimentation in Qingxi sag, Jiuquan Basin on the northern Tibetan Plateau

Based on comprehensive studies in petrography, petrofabric analysis and geochemistry, this paper describes a unique and rare laminated micritic ferruginous primary dolostone crystallized and precipitated from the alkaline hot brine under the conditions of the Mesozoic faulted lake basin. The main rock-forming mineral of this dolostone is ferruginous dolomite with a micritic structure. This dolomite mostly exhibits laminae of 0.1–1 mm thick and is often discovered with other minerals, such as albite, analcite, barite and dickite, which have at least two types of interbedded laminae. Petrogeochemistry reveals that this dolostone contains a large number of typomorphic elements of hydrothermal sedimentation, including Sb, Ba, Sr, Mn, and V. In addition, the LREE is in relatively high concentrations and possesses the typical REE distribution pattern with negative Eu anomaly. Oxygen isotope values (δ¹⁸O_PDB) range from 5.89‰ to 14.15‰ with an average of 9.69‰. The ratio of ⁸⁷Sr/⁸⁶Sr is between 0.711648 and 0.719546, with an average of 0.714718. These data indicate that the depositional environment is a stable, blocked, anoxic low-lying hot brine pool in the bottom of deep lake controlled by basement faults. The hydrothermal fluid is the alkaline hot brine formed by the combination of the infiltration lake water and mantle-derived magmatic water, consisting of many ions, including Ca²⁺, Mg²⁺ and Fe²⁺. Under the driving flow power of magmatic heat, gravity and compaction, the hydrothermal fluid overcame the overburden pressure and hydrostatic pressure of the lake water body, and boiled to explosion, and then the explosion shattered the original laminated micritic ferruginous primary dolostone near the vent and then formed a new type of dolostone called shattered “hydroexplosion breccias”. In the low-lying, unperturbed hot brine pool, far from the vent, the laminated micritic ferruginous primary dolostone was quickly crystallized and chemicals precipitated from the hydrotherm. This study of special rocks contributes to research into the causes of the formation of lacustrine carbonate rocks and dolostone. In particular, it provides new examples and research insights for future studies of the lacustrine dolomite from the similar Mesozoic and Cenozoic basins in China.     

Methods and procedures to determine the outer limits of the continental shelf beyond 200 nautical miles

This paper establishes techniques and methods to determine a variety of boundaries associated with 200 nautical miles beyond the continental shelf. The methods, based on topography, slope and second-deriv- ative profile integrated analysis, are now able to identify automatically the foot of the continental slope （FOS）. By analyzing the sedimentary profile, the points of 1% sediment thickness are recognized. Through the intersection, cut, deletion and mergence calculation of the extrapolated data set of fLxed-point series, the method succeeds in generating automatically the extrapolated boundaries, including the FOS＋60 M line, the 350 M line, and the 2500 m＋100 M line. In addition, based on the automatic analysis of the topographic profile, it can be applied to determine rapidly the points of maximum water depth. Taking the northern Okinawa Trough （OT） as an example, these methods are used to calculate and examine the boundaries in- cluded in the Submission by the People＇s Republic of China Concerning the Outer Limits of the Continental Shelf beyond 200 Nautical miles in Part of the East China Sea （ECS）; the boundaries thus derived have a solid scientific and rational basis.     

应用GasBench Ⅱ-IRMS优化碳氧同位素分析方法

GasBenchⅡ-连续流稳定同位素质谱仪(IRMS)联用在线分析已成为碳酸盐碳氧同位素分析测试的常用方法,已有研究认为不同的实验条件直接影响δ¹³C和δ¹⁸O同位素测试结果的准确性。但这些报道未对该联用方法所涉及的实验条件进行综合分析。本文系统研究了GasBenchⅡ-IRMS法中各种实验条件(包括排空时间、反应温度、反应时间和色谱分离温度)对碳氧同位素测试结果的综合影响。结果表明:排空时间大于9 min可有效消除空气对测试结果的干扰,不同的反应温度和时间对碳氧同位素分析结果均有一定影响,经条件优化确定反应温度为72℃,反应时间为60 min,色谱分离温度为60℃。在优化的实验条件下,碳氧同位素分析精度分别优于0.03‰和0.05‰,达到了国际分析测试水平。同时,选择合适的同位素数据归一化方法可以进一步保证碳氧同位素测试结果的准确性和可靠性。通过分析近4000件实际样品,对比单一标准物质校准和双标准物质校准同位素归一化方法的计算结果,发现双标准物质校准偏差小于单一标准物质校准偏差,因此建议采用双标准物质校准法进行样品同位素标准化计算。本研究为GasBenchⅡ-IRMS联用技术中实验条件的选取提供了一定的参考,保证碳氧同位素测试结果的可靠性和准确性。同时提出,由于样品成分复杂且不均一,在分析实际样品时需要根据样品的性质进一步对实验条件进行考察。     

黎平双江电站水库暴雨洪水设计

该文选用参证站资料的方法,对黎平县双江电站水库1954—2021年近68 a来逐年最大日降水量采用PearsonⅢ型研究方法和贵州省暴雨洪水计算公式进行研究。结果表明：黎平双江电站水库年最大日降水量年变化呈上升趋势,2010年以后上升趋势较显著。暴雨洪水设计以H_1d=119.29 mm、C_v=0.47、C_s/C_v=3.5作为研究成果,防洪标准按50 a一遇的暴雨洪水设计成果为P=2.0%,日最大降水量=277 mm、洪峰流量=2509 m³·s^-1;洪水校核按500 a一遇的暴雨洪水设计成果为P=0.2%,日最大降水量=391 mm、洪峰流量=3905 m³·s^-1;消能防冲设计标准按30 a一遇的设计成果为P=3.3%,日最大降水量=252 mm、洪峰流量=2209 m³·s^-1。研究成果对黎平双江电站水库预防灾害性强降水、安全渡汛和水库优化调度、提高产能具有十分重要...     

岩石嵌固掏挖基础抗拔承载特性及其影响因素研究

岩石嵌固掏挖基础目前已经广泛应用于电力基础工程中。原状土由于受扰动较小,胶结性强,具有良好的抗剪强度,对掏挖基础抗拔承载力具有重要影响,因此研究原状土参数变化对基础上拔承载性能的影响规律具有重要意义。结合现场试验,建立数值模型,研究土体黏聚力、内摩擦角、弹性模量对基础上拔承载性能的影响规律。研究表明:土体内摩擦角和黏聚力对基础抗拔承载力具有较大影响,而弹性模量影响程度较低;参数的变化对土体塑性区发展规律影响较小。