Calcium and magnesium isotope systematics in rivers draining the Himalaya-Tibetan-Plateau region: Lithological or fractionation control?

In rivers draining the Himalaya-Tibetan-Plateau region, the ²⁶Mg/²⁴Mg ratio has a range of 2‰ and the ⁴⁴Ca/⁴²Ca ratio has a range of 0.6‰. The average δ²⁶Mg values of tributaries from each of the main lithotectonic units (Tethyan Sedimentary Series (TSS), High Himalayan Crystalline Series (HHCS) and Lesser Himalayan Series (LHS)) are within 2 standard deviation analytical uncertainty (0.14‰). The consistency of average riverine δ²⁶Mg values is in contrast to the main rock types (limestone, dolostone and silicate) which range in their average δ²⁶Mg values by more than 2‰. Tributaries draining the dolostones of the LHS differ in their values compared to tributaries from the TSS and HHCS. The chemistry of these river waters is strongly influenced by dolostone (solute Mg/Ca close to unity) and both δ²⁶Mg (−1.31‰) and (0.64‰) values are within analytical uncertainty of the LHS dolostone. These are the most elevated values in rivers and rock reported so far demonstrating that both riverine and bedrock values may show greater variability than previously thought.Although rivers draining TSS limestone have the lowest values at −1.41 and 0.42‰, respectively, both are offset to higher values compared to bedrock TSS limestone. The average δ²⁶Mg value of rivers draining mainly silicate rock of the HHCS is −1.25‰, lower by 0.63‰ than the average silicate rock. These differences are consistent with a fractionation of δ²⁶Mg values during silicate weathering. Given that the proportion of Mg exported from the Himalaya as solute Mg is small, the difference in ²⁶Mg/²⁴Mg ratios between silicate rock and solute Mg reflects the ²⁶Mg/²⁴Mg isotopic fractionation factor () between silicate and dissolved Mg during incongruent silicate weathering. The value of of 0.99937 implies that in the TSS, solute Mg is primarily derived from silicate weathering, whereas the source of Ca is overwhelmingly derived from carbonate weathering. The average value in HHCS rivers is within uncertainty of silicate rock at 0.39‰. The widespread hot springs of the High Himalaya have an average δ²⁶Mg value of −0.46‰ and an average value of 0.5‰, distinct from riverine values for δ²⁶Mg but similar to riverine values. Although rivers draining each major rock type have and δ²⁶Mg values in part inherited from bedrock, there is no correlation with proxies for carbonate or silicate lithology such as Na/Ca ratios, suggesting that Ca and Mg are in part recycled. However, in spite of the vast contrast in vegetation density between the arid Tibetan Plateau and the tropical Lesser Himalaya, the isotopic fractionation factor for Ca and Mg between solute and rocks are not systematically different suggesting that vegetation may only recycle a small amount of Ca and Mg in these catchments.The discrepancy between solute and solid Ca and Mg isotope ratios in these rivers from diverse weathering environments highlight our lack of understanding concerning the origin and subsequent path of Ca and Mg, bound as minerals in rock, and released as cations in rivers. The fractionation of Ca and Mg isotope ratios may prove useful for tracing mechanisms of chemical alteration. Ca isotope ratios of solute riverine Ca show a greater variability than previously acknowledged. The variability of Ca isotope ratios in modern rivers will need to be better quantified and accounted for in future models of global Ca cycling, if past variations in oceanic Ca isotope ratios are to be of use in constraining the past carbon cycle.     

Bimodal volcanism in northeast Puerto Rico and the Virgin Islands (Greater Antilles Island Arc): Genetic links with Cretaceous subduction of the mid-Atlantic ridge Caribbean spur

Bimodal extrusive volcanic rocks in the northeast Greater Antilles Arc consist of two interlayered suites, including (1) a predominantly basaltic suite, dominated by island arc basalts with small proportions of andesite, and (2) a silicic suite, similar in composition to small volume intrusive veins of oceanic plagiogranite commonly recognized in oceanic crustal sequences. The basaltic suite is geochemically characterized by variable enrichment in the more incompatible elements and negative chondrite-normalized HFSE anomalies. Trace element melting and mixing models indicate the magnitude of the subducted sediment component in Antilles arc basalts is highly variable and decreases dramatically from east to west along the arc. In the Virgin Islands, the sediment component ranges between< 0.5 to  1% in Albian rocks, and between  1 and 2% in succeeding Cenomanian to Campanian strata. In comparison, sediment proportions in central Puerto Rico range between 0.5 to 1.5% in the Albian to 2 to > 4% during the Cenomanian-Campanian interval. The silicic suite, consisting predominantly of rhyolites, is characterized by depleted Al₂O₃ (average < 16%), low Mg-number (molar Mg/Mg + Fe < 0.5), TiO₂ (< 1.0%), and Sr/Y (< 10), oceanic or arc-like Sr, Nd, and Pb isotope signatures, and by the presence of plagioclase. All of these features are consistent with an anatexic origin in gabbroic sources, of both oceanic and arc-related origin, within the sub-arc basement. The abundance of silicic lavas varies widely along the length of the arc platform. In the Virgin Islands on the east, rhyolites comprise up to 80% of Lower Albian strata (112 to 105 Ma), and about 20% in post-Albian strata (105 to 100 Ma). Farther west, in Puerto Rico, more limited proportions (< 20%) of silicic lavas were erupted. The systematic variation of both sediment flux and abundance of crustally derived silicic lavas are consistent with current tectonic models of Caribbean evolution involving approximately perpendicular subduction of the Caribbean spur of the mid-Atlantic Ridge, which was located approximately midway between North and South America until Campanian times. Within this hypothetical setting the centrally positioned Virgin Islands terrain remained approximately fixed above the subducting ridge as the Antilles arc platform swept northeastward into the slot between the Americas. Accordingly, heat flow in the Virgin Islands was elevated throughout the Cretaceous, giving rise to widespread crustal melting, whereas the subducted sediment flux was limited. Conversely, toward the west in central Puerto Rico, which was consistently more remote from the subducting ridge, heat flow was relatively low and produced limited crustal melting, while the sediment flux was comparatively elevated.     

Geology,fluid inclusion and sulphur isotope characteristics of the El Cobre VHMS deposit,Southern Cuba

The El Cobre deposit is located in eastern Cuba within the volcanosedimentary sequence of the Sierra Maestra Paleogene arc. The deposit is hosted by tholeiitic basalts, andesites and tuffs and comprises thick stratiform barite and anhydrite bodies, three stratabound disseminated up to massive sulphide bodies produced by silicification and sulphidation of limestones or sulphates, an anhydrite stockwork and a siliceous stockwork, grading downwards to quartz veins. Sulphides are mainly pyrite, chalcopyrite and sphalerite; gold occurs in the stratabound ores. Fluid inclusions measured in sphalerite, quartz, anhydrite and calcite show salinities between 2.3 and 5.7 wt% NaCl eq. and homogenisation temperatures between 177 and 300°C. Sulphides from the stratabound mineralisation display δ ³⁴S values of 0‰ to +6.0‰, whilst those from the feeder zone lie between −1.4‰ and +7.3‰. Sulphides show an intra-grain sulphur isotope zonation of about 2‰; usually, δ ³⁴S values increase towards the rims. Sulphate sulphur has δ ³⁴S in the range of +17‰ to +21‰, except two samples with values of +5.9‰ and +7.7‰. Sulphur isotope data indicate that the thermochemical reduction of sulphate from a hydrothermal fluid of seawater origin was the main source of sulphide sulphur and that most of the sulphates precipitated by heating of seawater. The structure of the deposit, mineralogy, fluid inclusion and isotope data suggest that the deposit formed from seawater-derived fluids with probably minor supply of magmatic fluids.     

Mineralogical,petrological, and geochemical studies of the Limahe mafic–ultramatic intrusion and associated Ni–Cu sulfide ores,SW China

The Limahe Ni–Cu sulfide deposit is hosted by a small mafic–ultramafic intrusion (800 × 200 × 300 m) that is temporally associated with the voluminous Permian flood basalts in SW China. The objective of this study is to better understand the origin of the deposit in the context of regional magmatism which is important for the ongoing mineral exploration in the region. The Limahe intrusion is a multiphase intrusion with an ultramafic unit at the base and a mafic unit at the top. The two rock units have intrusive contacts and exhibit similar mantle-normalized trace element patterns and Sr–Nd isotopic compositions but significantly different cumulus mineralogy and major element compositions. The similarities suggest that they are related to a common parental liquid, whereas the differences point to magma differentiation by olivine crystallization at depth. Sulfide mineralization is restricted to the ultramafic unit. The abundances of sulfides in the ultramafic unit generally increase towards the basal contacts with sedimentary footwall. The δ ³⁴S values of sulfide minerals from the Limahe deposit are elevated, ranging from +2.4 to +5.4‰. These values suggest the involvement of external S with elevated δ ³⁴S values. The mantle-normalized platinum-group element (PGE) patterns of bulk sulfide ores are similar to those of picrites associated with flood basalts in the region. The abundances of PGE in the sulfide ores, however, are significantly lower than that of sulfide liquid expected to segregate from undepleted picrite magma. Cr-spinel and olivine are present in the Limahe ultramafic rocks as well as in the picrites. Mantle-normalized trace element patterns of the Limahe intrusion generally resemble those of the picrites. However, negative Nb–Ta anomalies, common features of contamination with the lower or middle crust, are present in the intrusion but absent in the picrites. Sr–Nd isotopes suggest that the Limahe intrusion experienced higher degrees of contamination with the upper crust than did the picrites. The results of this study permit us to suggest that the parental magma of the Limahe intrusion was derived from picritic magma by olivine fractionation and contamination in a staging chamber at mid-crustal levels. Depletion of PGE in the sulfide ores in the Limahe intrusion is likely due to previous sulfide segregation of the parental magmas in the staging chamber. Sulfide mineralization in the Limahe intrusion is related to second-stage sulfide segregation after the fractionated magmas acquired external S from pyrite-bearing country rocks during magma ascent to the Limahe chamber. The abrupt change in mineralogical and chemical compositions between the ultramafic unit and the overlying unit suggests that at least two separate pulses of magma were involved in the development of the Limahe intrusion. We propose that the Limahe intrusion was once a wider part of a dynamic conduit that fed magma to the overlying subvolcanic dykes/sills or lavas. The ultramafic unit formed by the first, relatively more primitive magma, and the mafic unit formed by the second, relatively more fractionated magma. Immiscible sulfide droplets that segregated from the first magma settled down with olivine crystals to form the sulfide-bearing, olivine-rich rocks in the base of the intrusion. The overlying residual liquids were then pushed out of the chamber by the second magma. Critical factors for the formation of an economic Ni–Cu sulfide deposit in such a small intrusion include the dynamic petrologic processes involved and the availability of external sulfur. The Limahe deposit reminds us that small, multiphase, mafic–ultramafic intrusions in the region should not be overlooked for the potential of economic Ni–Cu sulfide deposits.     

Absolute Calibration of an Ashtech Z12-T GPS Receiver

Dual-frequency carrier phase and code measurements from geodetic type receivers are a promising tool for frequency and time transfer. In order to use them for clock comparisons, all instrumental delays should be calibrated. We have carried out the calibration of one such receiver, an Ashtech Z12-T type, by two different methods: first, by absolute calibration using a GPS simulator; second, by differential calibration with respect to a time transfer receiver that had previously been calibrated. We present the experimental set-ups and the results of the two experiments and estimate the uncertainty budget. An ultimate uncertainty of order 1 ns in the absolute calibration seems to be attainable. ? 2001 John Wiley & Sons, Inc.     

Enclosure experiments on survival and growth of black drum eggs and larvae in lower Chesapeake Bay

Experiments in 2.2 m³, in situ mesocosm enclosures indicate that black drum, Pogonias cromis, eggs and larvae potentially can survive in the lower Chesapeake Bay at ambient microzooplankton prey levels (≈200 prey 1^?1) in the absence of predators. In growth experiments, larva mean growth rates to 10 d posthatch were similar (0.17 mm d^?1 and 0.18 mm d^?1) when fed at prey levels of 50 prey 1^?1 and 200 prey 1^?1. Individual growth rates, however, were more variable at 50 prey 1^?1. Mortality rates also were comparable in 50 (27% d^?1) and 200 (23% d^?1) prey 1^?1 enclosures. In a second experiment, the predation potentials of the hydromedusa Nemopsis bachei and the lobate ctenophore Mnemiopsis leidyi were estimated in relation to initial black drum egg prey density, presence of alternative <1 mm zooplankton prey, and estimated daily abundance of the jellyfish on the black drum spawning grounds. Mortality rates per medusa and ctenophore were similar (0.02–0.03 d^?1), were not affected by presence of alternative prey, and were directly related to initial egg density. Results suggest that the gelatinous predators, especially the hydromedusa, could have cleared a high (≈38%) but variable fraction of the water column daily of fish eggs and yolk-sac larvae during the black drum spawning season. We hypothesize that the poor or episodic recruitment success of black drum in Chesapeake Bay results from a short spawning season that often coincides with abundance peaks of gelatinous predators and that predation on eggs and yolk-sac larvae may control recruitment.     

On predicting the response of forests in eastern North America to future climatic change

Our ability to accurately predict the response of forests in eastern North America to future climatic change is limited by our knowledge of how different tree species respond to climate. When the climatic response of eastern hemlock is modeled across its range, we find that the assumed climatic response used in simulation models is not sufficient to explain how this species is presently responding to climate. This is also the case for red spruce growing in the northern Appalachian Mountains. Consequently, simulations of future change to forests that include eastern hemlock and red spruce may need to be improved. We suspect that similar findings will be made when other tree species are studied in detail using tree-ring analysis. If so, our present understanding of how individual tree species respond to climate may not be adequate for accurately predicting future changes to these forests. Tree-ring analysis can increase our understanding of how climate affects tree growth in eastern North America and, hence, provide the knowledge necessary to produce more accurate predictions.     

Laboratory Demonstration of Hydrocarbon Migration in the Vadose Zone: Effectiveness of the U-Tube Design for Underground Storage Tank Leak Detection Monitoring

The experimental results derived from a laboratory model of gasoline migration from a simulated leaking underground storage tank (UST) demonstrate that the direction of migration through the simulated fill material is essentially straight down. Consequently, the U-tube design for leak detection monitoring of USTs has limited utility because that design relies on the assumption that the path of migration of the leaked fluids will follow the surface of the tank to the bottom and be intercepted by the U-tube below.     

Sheared shale response to deep TBM excavation

Phien-wej, N. and Cording, E.J., 1991. Sheared shale response to deep TBM excavation. Eng. Geol., 30: 371–391.

Ravelling and squeezing of sheared shale of Stillwater Tunnel caused severe problems in tunneling with a tunnel boring machine (TBM) that led to termination of the contract. The tunnel was finally holed through with two TBM's specially designed for squeezing ground. Although the shale mass in all geological conditions exhibited time-dependent response, significant squeezing was confined to sheared shale with large amounts of clay gouge infill, wherein creep of the clay gouge was the prime mechanism controlling the ground response. However, when the tunnel face was advanced at a slow rate, the observed ground squeezing in the early period was largely induced by the effect of stress change from face advance, not the creep. Ground ravelling was very significant in sheared shale due to the high degree of fissuring and fracturing of this thinly bedded shale. Failure of the first TBM resulted mainly from the incompatibility of the shield design with the sheared shale. The shield was too long and stiff and had variable diameters. Extensive observation and instrumentation programs of the project provided valuable information on rapid mechanized tunneling in heavy ground.     

Three dilemmas in the integrated assessment of climate change

Conclusions These three dilemmas embody the hardest, most important, and most enduring problems of doing assessment well. None admits simple, obvious solutions. Each can be managed better or worse for any particular assessment endeavor, but doing better requires clear understanding of the purpose of the endeavor. What ways of combining different pieces of disciplinary knowledge, of making projections, and of pursuing policy relevance are more or less appropriate will differ, depending on whether a project seeks to characterize uncertainties and gaps in knowledge; to advise a particular policy choice; to support dialog among policy actors; or to facilitate inquiry into relevant values or goals. Evaluation of the relative emphasis, the methods, and the process of an assessment can only be done relative to some such purpose.Of course, some pitfalls may be so serious as to thwart any purpose, as Risbey et al.'s discussion of the global modeling movement reminds us. The global models' most obvious pitfalls — inadequate treatment of uncertainty, neglect of economic adjustment, excessive confidence in predictions — have largely been seen and avoided by the current assessment community (though there may be more to be learned even here). But on the subtler questions of how assessment or modeling can contribute most usefully to policy, little progress has been made since the 1970s. Consequently, though assessment has advanced in many ways since then, IA remains at risk of suffering the same fate as the global models: a cycle of early enthusiasm, followed by a reaction of frustration and excessive, undeserved rejection.Current endeavors in IA have made substantial contributions to identifying and prioritizing knowledge needs, less to informing specific policy choice. Further progress cannot be guided by a single canonical view of what assessment should be and do, but will proceed incrementally down multiple paths. Several paths currently appear promising: analytic approaches to better represent multiple actors, diverse preferences, and multiple valued outcomes; better representation and application of uncertainty, including diverse expert opinion; novel methods to link assessment with policy communities; and broader participation in assessment teams and explicit focus on negotiating and elaborating pragmatic, viable critical standards. Risbey et al.'s call to develop institutions for critical reflection, mutual learning, and self-improvement will be crucial in developing and evaluating the progress made down these paths.Morgan and Dowlatabadi's checklist for desiderata of IA is a good starting point for a conversation about assessment standards, to which I would propose a few extensions and elaborations. First, there should be not just multiple assessments, but multiple assessment projects using diverse collections of methods and approaches. Second, assessment projects should explore novel methods for connecting their work with the policy community. Third, the approach should be iterative not just within each project, but across assessment projects and between them and the policy community. Fourth, assessors should not be embarrassed by, or seek to disguise, results that are merely illustrative, non-authoritative, and suggestive; these should be acknowledged as such, and the vigorous questioning and critique that will come, including partisan critique, accepted. Do not seek to avoid criticism by mumbling. An important limit to this checklist approach is suggested, though, by the way various writers have groped to define assessment standards by analogy to other domains, revealing how limited is our understanding of how to evaluate assessment. Risbey et al. refer to connoisseurship, as if assessment is like fine wine; Clark and Majone (1985) refer to artistic criticism, as if assessment is like opera singing. If these analogies are appropriate, then pursuing a single set of critical standards for assessment is at least premature, possibly erroneous. Rather, there should be a diversity of approaches, perhaps so broad that no single set of criteria for excellence could be defined. The pragmatic middle way between the too-limiting application of a single set of standards, and an anarchic refusal to evaluate, will have to be negotiated, defined, and improved incrementally.