Assessment of sandstone deterioration at Ta Keo temple (Angkor): first results and future prospects

A first application of geomorphological methods to the assessment of sandstone deterioration at Angkor is presented. Damage diagnosis was carried out on the first eastern tier of the central pyramid of the 1,000 year-old Ta Keo temple. Methods combine field observations and measurements at 230 sampling points, high-resolution lasergrammetry and stereophotogrammetry on a 2-m² test zone, and SEM observations. The first results indicate that decay operates through a synergistic combination of weathering phenomena dominated by scaling and solution, and exhibits a high spatial variability. Percentages of deteriorated surfaces vary from 17.6 to 93.8%, and average stone recession values from 0.00 to 2.71 cm (minimum) and 0.34 to 5.49 cm (maximum). On the test-zone, stereophotogrammetry and 3D-mapping of the present and reconstructed initial states using lasergrammetry indicate that erosion scars up to 6 cm deep have formed since 1963. On the whole, the amount of deteriorated surfaces more than tripled between 1963 and 2008. The degree of implication of salts in stone decay remains unclear for most efflorescences are composed of calcite (CaCO3), with secondary importance of barite (BaSO4) and gypsum (CaSO₄·2H₂O). Future prospects aim to evaluate the impact on stone decay of the clearing out of the temple from the forest in the 1920s.     

Environmental risk evaluation of the use of mine spoils and treated sewage sludge in the ecological restoration of limestone quarries

The ecologic restoration criteria in areas degraded from extraction activities require making use of their mine spoils. These materials do not meet fertility conditions to guarantee restoration success and therefore, need the incorporation of organic amendments to obtain efficient substratum. Reducing the deficiencies in the organic material and restoration material nutrients with the contribution of treated sewage sludge is proposed in this work. This experiment was based on a controlled study using columns. The work was conducted with two mine spoils, both very rich in calcium carbonate. The first mineral, of poor quality, came from the formation of aggregates of crushed limestone (Z). The other residual material examined originated in limestone extraction, formed by the levels of interspersed non-limestone materials and the remains of stripped soils (D). Two treatments were undertaken (30,000 and 90,000 kg/ha of sewage sludge), in addition to a control treatment. The water contribution was carried out with a device that simulated either short-duration rain or a flooding irrigation system in order to cover the surface and then percolate through the soil. The collection of leached water took place 24 h after the applications. Different parameters of the leached water were determined, including pH, electrical conductivity, nitrate anions, ammonium, phosphates, sulphates and chlorides. The values obtained for each irrigation application are discussed, and the nitrate values obtained were very elevated.     

Sediment Trend Analysis through the variation of granulometric parameters: A review of theories and applications

Spatial variations in grain-size parameters (i.e. grain-size trends) contain information on sediment transport patterns. Analytical procedures have been proposed using the grain-size trend to determine net sediment transport pathways. In the first part of this study, the fundamentals of the theory are presented through methods for analysing 1D and 2D variations. The methods used are critically discussed, while pointing out some severe problems. So far, these methods suffer from limitations leading to serious interpretational errors, making it necessary to take account of two kinds of uncertainties. Inputs uncertainties are linked to the physical sediment properties as well as procedures of sampling and analysis. Model uncertainties are then discussed for each step of the grain-size trend analysis. The validity of Sediment Trend Analysis under natural conditions is tested against published field studies to determine the most appropriate variation trend to use in a specific environment. Proposals are given for each step of the procedure for optimal use of the method using a Quality Assurance (QA) approach. Further developments are proposed, such as integration into a Geographic Information System.     

Determination of fluid/melt partition coefficients by LA-ICPMS analysis of co-existing fluid and silicate melt inclusions: Controls on element partitioning

Analyses of co-existing silicate melt and fluid inclusions, entrapped in quartz crystals in volatile saturated magmatic systems, allowed direct quantitative determination of fluid/melt partition coefficients. Investigations of various granitic systems (peralkaline to peraluminous in composition, log fO₂ = NNO−1.7 to NNO+4.5) exsolving fluids with various chlorinities (1-14 mol/kg) allowed us to assess the effect of these variables on the fluid/melt partition coefficients (D). Partition coefficients for Pb, Zn, Ag and Fe show a nearly linear increase with the chlorinity of these fluid (D_Pb ∼ 6 ∗ m_Cl, D_Zn ∼ 8 ∗ m_Cl, D_Ag ∼ 4 ∗ m_Cl, D_Fe ∼ 1.4 ∗ m_Cl, where m_Cl is the molinity of Cl). This suggests that these metals are dissolved primarily as Cl-complexes and neither oxygen fugacity nor the composition of the melt affects significantly their fluid/melt partitioning. By contrast, partition coefficients for Mo, B, As, Sb and Bi are highest in low salinity (1-2 mol/kg Cl) fluids with maximum values of D_Mo ∼ 20, D_B ∼ 15, D_As ∼ 13, D_Sb ∼ 8, D_Bi ∼ 15 indicating dissolution as non-chloride (e.g., hydroxy) complexes. Fluid/melt partition coefficients of copper are highly variable, but highest between vapor like fluids and silicate melt (D_Cu ? 2700), indicating an important role for ligands other than Cl. Partition coefficients for W generally increase with increasing chlorinity, but are exceptionally low in some of the studied brines which may indicate an effect of other parameters. Fluid/melt partition coefficients of Sn show a high variability but likely increase with the chlorinity of the fluid (D_Sn = 0.3-42, D_W = 0.8-60), and decrease with decreasing oxygen fugacity or melt peraluminosity.     

Sedimentary petrology and geochemistry of siliciclastic rocks from the upper Jurassic Tordillo Formation (Neuquén Basin, western Argentina): Implications for provenance and tectonic setting

The Upper Jurassic Tordillo Formation is exposed along the western edge of the Neuquén Basin (west central Argentina) and consists of fluvial strata deposited under arid/semiarid conditions. The pebble composition of conglomerates, mineralogical composition of sandstones and pelitic rocks, and major- and trace-element geochemistry of sandstones, mudstones, and primary pyroclastic deposits are evaluated to determine the provenance and tectonic setting of the sedimentary basin. Conglomerates and sandstones derived almost exclusively from volcanic sources. The stratigraphic sections to the south show a clast population of conglomerates dominated by silicic volcanic fragments and a predominance of feldspathic litharenites. This framework composition records erosion of Triassic–Jurassic synrift volcaniclastic rocks and basement rocks from the Huincul arch, which was exhumed as a result of Late Jurassic inversion. In the northwestern part of the study area, conglomerates show a large proportion of mafic and acidic volcanic rock fragments, and sandstones are characterised by a high content of mafic volcanic rock fragments and plagioclase. These data suggest that the source of the sandstones and conglomerates was primarily the Andean magmatic arc, located west of the Neuquén Basin. The clay mineral assemblage is interpreted as the result of a complex set of factors, including source rock, climate, transport, and diagenesis. Postdepositional processes produced significant variations in the original compositions, especially the fine-grained deposits. The Tordillo sediments are characterised by moderate SiO₂ contents, variable abundances of K₂O and Na₂O, and a relatively high proportion of ferromagnesian elements. The degree of chemical weathering in the source area, expressed as the chemical index of alteration, is low to moderate. The major element geochemistry and Th/Sc, K/Rb, Co/Th, La/Sc, and Cr/Th values point to a significant input of detrital volcanic material of calcalkaline felsic and intermediate composition. However, major element geochemistry is not useful for interpreting the tectonic setting. Discrimination plots based on immobile trace elements, such as Ti, Zr, La, Sc, and Th, show that most data lie in the active continental margin field. Geochemical information is not sufficiently sensitive to differentiate the two different source areas recognized by petrographic and modal analyses of conglomerates and sandstones.     

The passivation of calcite by acid mine water. Column experiments with ferric sulfate and ferric chloride solutions at pH 2

Column experiments, simulating the behavior of passive treatment systems for acid mine drainage, have been performed. Acid solutions (HCl or H₂SO₄, pH 2), with initial concentrations of Fe(III) ranging from 250 to 1500 mg L⁻¹, were injected into column reactors packed with calcite grains at a constant flow rate. The composition of the solutions was monitored during the experiments. At the end of the experiments (passivation of the columns), the composition and structure of the solids were measured. The dissolution of calcite in the columns caused an increase in pH and the release of Ca into the solution, leading to the precipitation of gypsum and Fe–oxyhydroxysulfates (Fe(III)–SO₄–H⁺ solutions) or Fe–oxyhydroxychlorides (Fe(III)–Cl–H⁺ solutions). The columns worked as an efficient barrier for some time, increasing the pH of the circulating solutions from 2 to 6–7 and removing its metal content. However, after some time (several weeks, depending on the conditions), the columns became chemically inert. The results showed that passivation time increased with decreasing anion and metal content of the solutions. Gypsum was the phase responsible for the passivation of calcite in the experiments with Fe(III)–SO₄–H⁺ solutions. Schwertmannite and goethite appeared as the Fe(III) secondary phases in those experiments. Akaganeite was the phase responsible for the passivation of the system in the experiments with Fe(III)–Cl–H⁺ solutions.     

Quantitative sinkhole hazard assessment. A case study from the Ebro Valley evaporite alluvial karst (NE Spain)

Quantitative sinkhole hazard assessments in karst areas allow calculation of the potential sinkhole risk and the performance of cost-benefit analyses. These estimations are of practical interest for planning, engineering, and insurance purposes. The sinkhole hazard assessments should include two components: the probability of occurrence of sinkholes (sinkholes/km² year) and the severity of the sinkholes, which mainly refers to the subsidence mechanisms (progressive passive bending or catastrophic collapse) and the size of the sinkholes at the time of formation; a critical engineering design parameter. This requires the compilation of an exhaustive database on recent sinkholes, including information on the: (1) location, (2) chronology (precise date or age range), (3) size, and (4) subsidence mechanisms and rate. This work presents a hazard assessment from an alluvial evaporite karst area (0.81 km²) located in the periphery of the city of Zaragoza (Ebro River valley, NE Spain). Five sinkholes and four locations with features attributable to karstic subsidence where identified in an initial investigation phase providing a preliminary probability of occurrence of 0.14 sinkholes/km² year (11.34% in annual probability). A trenching program conducted in a subsequent investigation phase allowed us to rule out the four probable sinkholes, reducing the probability of occurrence to 0.079 sinkholes/km² year (6.4% in annual probability). The information on the severity indicates that collapse sinkholes 10–15 m in diameter may occur in the area. A detailed study of the deposits and deformational structures exposed by trenching in one of the sinkholes allowed us to infer a modern collapse sinkhole approximately 12 m in diameter and with a vertical throw of 8 m. This collapse structure is superimposed on a subsidence sinkhole around 80 m across that records at least 1.7 m of synsedimentary subsidence. Trenching, in combination with dating techniques, is proposed as a useful methodology to elucidate the origin of depressions with uncertain diagnosis and to gather practical information with predictive utility about particular sinkholes in alluvial karst settings: precise location, subsidence mechanisms and magnitude, and timing and rate of the subsidence episodes.     

Flood hazard delineation combining geomorphological and hydrological methods: an example in the Northern Iberian Peninsula

Flood mapping requires the combination and integration of geomorphological and hydrological-hydraulic methods; however, despite this, there is very little scientific literature that compares and validates both methods. Two types of analysis are addressed in the present article. On the one hand, maps of flood plains have been elaborated using geomorphological evidence and historical flood data in the mountainous area of northwestern Spain, covering an area of more then 232 km² of floodplains. On the other hand, a hydrometeorological model has been developed (Clark semidistributed unit hydrograph) in the Sarria River basin (155 km², NW Spain). This basin is not gauged, hence the model was subjected to a goodness-of-fit test of its parameter (curve number) by means of Monte Carlo simulation. The peak flows obtained by means of the hydrological model were used for hydraulic modeling (one-phase, one-dimensional and steady flow) in a 4 km² urban stretch of the river bed. The delineation of surface areas affected by floods since 1918, as well as those analyzed subsequent to the geomorphological study, reveals a high degree of reliability in the delineation of the flooded areas with frequent recurrence intervals (<50 years). If we compare these flooded surface areas with the estimate obtained by the hydrological-hydraulic method we can see that the latter method overestimates the extent of the surface water by 144% for very frequent recurrence intervals (>10 years) and underestimates it as the recurrence interval increases, by up to 80% less floodplain for exceptional events (>500 years). Finally, a management map is put forth combining the most reliable results available by integrating both methods. Originally presented at the Sixth International Conference on Geomorphology.     

Mineralogy and geochemistry of El Dorado epithermal gold deposit, El Sauce district, central-northern Chile

Summary The El Dorado Au-Cu deposit is located in an extensive intra-caldera zone of hydrothermal alteration affecting Upper Cretaceous andesites of the Los Elquinos Formation at La Serena (≈ 29°47′S Lat., 70°43′W Long., Chile). Quartz-sulfide veins of economic potential are hosted by N25W and N20E fault structures associated with quartz-illite alteration (+supergene kaolinite). The main ore minerals in the deposit are pyrite, chalcopyrite ± fahlore (As/(As + Sb): 0.06−0.98), with electrum, sphalerite, galena, bournonite-seligmanite (As/(As + Sb): 0.21−0.31), marcasite, pyrrhotite being accessory phases. Electrum, with an Ag content between 32 and 37 at.%, occurs interstitial to pyrite aggregates or along pyrite fractures. Pyrite commonly exhibits chemical zonation with some zones up to 1.96 at.% As. Electron probe microanalyses of pyrite indicate that As-rich zones do not exhibit detectable Au values. Fluid inclusion microthermometry shows homogenization temperatures between 130 and 352 °C and salinities between 1.6 and 6.9 wt.% NaCl eq. Isotope data for quartz, ankerite and phyllosilicates and estimated temperatures show that δ¹⁸O and δD for the hydrothermal fluids were between 3 and 10‰ and between −95 and −75‰, respectively. These results suggest the mineralizing fluids were a mixture of meteoric and magmatic waters. An epithermal intermediate-sulfidation model is proposed for the formation of the El Dorado deposit. Author’s present address: J. Carrillo-Rosúa, Dpto. de Didáctica de las Ciencias Experimentales, Universidad de Granada, Campus de Cartuja, 18071, Granada, Spain