Proximal Remote Sensing of Herbicide and Drought Stress in Field Grown Colocasia and Sweet Potato Plants by Sunlight-Induced Chlorophyll Fluorescence Imaging

Chlorophyll fluorescence is an indicator of plant photosynthetic activity and has been used to monitor the health status of vegetation. Several studies have exploited the application of red/far-red chlorophyll fluorescence ratio in detecting the impact of various types of stresses in plants. Recently, sunlight-induced chlorophyll fluorescence imaging has been used to detect and discriminate different stages of mosaic virus infection in potted cassava plants with a multi-spectral imaging system (MSIS). In this study, the MSIS is used to investigate the impact of drought and herbicide stress in field grown crop plants. Towards this control and treatment groups of colocasia and sweet potato plants were grown in laterite soil beds and the reflectance images of these crop plants were recorded up to 14-days of treatment at the Fraunhofer lines of O₂ B at 687 nm and O₂ A at 759.5 nm and the off-lines at 684 and 757.5 nm. The recorded images were analyzed using the Fraunhofer Line Discrimination technique to extract the sunlight-induced chlorophyll fluorescence component from the reflectance images of the plant leaves. As compared to the control group, the chlorophyll fluorescence image ratio (F ₆₈₇/F ₇₆₀) in the treatment groups of both the plant varieties shows an increasing trend with increase in the extent of stress. Further, the F ₆₈₇/F ₇₆₀ ratio was found to correlate with the net photosynthetic rate (Pn) and stomatal conductance (g_s) of leaves. The correlation coefficient (R ²) for the relationship of F ₆₈₇/F ₇₆₀ ratio with Pn were found to be 0.78, 0.79 and 0.78, respectively for the control, herbicide treated and drought treated colocasia plants, while these were 0.77, 0.86 and 0.88, respectively for sweet potato plants. The results presented show the potential of proximal remote sensing and the application F ₆₈₇/F ₇₆₀ fluorescence image ratio for effective monitoring of stress-induced changes in field grown plants.     

Algorithm for Harmonic Tidal Analysis along T/P Tracks： Taking Differences of Observed Sea Surface Heights at Adjacent Points as Observations

An algorithm （differential mode） is presented for the improvement of harmonic tidal analysis along T/P tracks, in which the differences between the observed sea surface heights at adjacent points are taken as observations. Also, the observation equations are constrained with the results of the crossover analysis; the parameter estimations are performed at 0.1° latitude intervals by the least squares. Cycle 10 to 330 T/P altimeter data covering the China Sea and the Northwest Pacific Ocean （2°-50° N,105°-150° E） are adopted for a refined along-track harmonic tidal analysis, and harmonic constants of 12 constituents in 8 474 points are obtained, which indicates that the algorithm can efficiently remove non-tidal effects in the altimeter observations, and improve the precision of tide parameters. Moreover, parameters along altimetry tracks represent a smoother distribution than those obtained by traditional algorithms. The root mean squares of the fitting errors between the tidal height model and the observations reduce from 11 cm to 1.3 cm.     

基于交互多模型的水下目标跟踪方法

According to the requirements of real-time performance and reliability in underwater maneuvering target tracking as well as clarifying motion features of the underwater target, an interacting multiple model algorithm based on fuzzy logic inference （FIMM） is proposed. Maneuvering patterns of the target are represented by model sets, including the constant velocity model （CA）, the Singer mode~, and the nearly constant speed horizontal-turn model （HT） in FIMM technology. The simulation results show that compared to conventional IMM, the reliability and real-time performance of underwater target tracking can be improved by FIMM algorithm.     

Bringing GPS into harsh environments for fully automated deformation monitoring

Engineering projects that require deformation monitoring frequently utilize geodetic sensors to measure displacements of target points located in the deformation zone. In situations where control stations and targets are separated by a kilometer or more, GPS can offer higher precision position updates at more frequent intervals than can normally be achieved using total station technology. For large-scale deformation projects requiring the highest precision, it is therefore advisable to use a combination of the two sensors. In response to the need for high precision, continuous GPS position updates in harsh deformation monitoring environments, a software has been developed that employs triple-differenced carrier-phase measurements in a delayed-state Kalman filter. Two data sets were analyzed to test the capabilities of the software. In the first test, a GPS antenna was displaced using a translation stage to mimic slow deformation. In the second test, data collected at a large open pit mine were processed. It was shown that the delayed-state Kalman filter developed could detect millimeter-level displacements of a GPS antenna. The actual precision attained depends upon the amount of process noise infused at each epoch to accommodate the antenna displacements. Higher process noise values result in quicker detection times, but at the same time increase the noise in the solutions. A slow, 25 mm displacement was detected within 30 min of the full displacement with sigma values in E, N and U of ±10 mm or better. The same displacement could also be detected in less than 5 h with sigma values in E, N and U of ±5 mm or better. The software works best for detecting long period deformations (e.g., 20 mm per day or less) for which sigma values of 1–2 mm are attained in all three solution components. It was also shown that the triple-differenced carrier-phase observation can be used to significantly reduce the effects of residual tropospheric delay that would normally plague double-differenced observations in harsh GPS environments.

Geodetic intersection on the ellipsoid

Through each of two known points on the ellipsoid a geodesic is passing in a known azimuth. We solve the problem of intersection of the two geodesics. The solution for the latitude is obtained as a closed formula for the sphere plus a small correction, of the order of the eccentricity of the ellipsoid, which is determined by numerical integration. The solution is iterative. Once the latitude is obtained, the longitude is determined without iteration.     

Low multipath antennas for GNSS-based attitude determination systems applied to high-altitude platforms

High-altitude platforms (HAPs) are a flexible and attractive technology for providing innovative wireless services. These aerial platforms can be successfully employed for mobile or broadband communications and for disaster monitoring or response. However, one of the open issues is whether HAP stations can provide reliable services without temporal outages owing to stratospheric winds that can cause positional and attitude instabilities thus affecting the communication system operation. To counteract this issue, one possible solution is to use reconfigurable antennas whose pointing direction can be adjusted depending on the platform spatial orientation. However, this would require real-time three-axial attitude data. As a possible solution, this paper will review the potential of GNSS-based attitude determination systems with reference to HAP stations. In particular, it will be shown how the use of a particular class of low multipath and lightweight antennas can provide a high degree of accuracy without altering the avionic ballast.     

Applications of Lodrigues Matrix in 3D Coordinate Transformation

Three transformation models (Bursa-Wolf, Molodensky, and WTUSM) are generally used between two data systems transformation. The linear models are used when the rotation angles are small; however, when the rotation angles get bigger, model errors will be produced. In this paper, we present a method with three main terms: ① the traditional rotation angles θ , φ ,ψ are substituted with a , b, c which are three re-spective values in the anti-symmetrical or Lodrigues matrix; ② directly and accurately calculating the formula of seven parameters in any value of rotation angles; and ③ a corresponding adjustment model is established. This method does not use the triangle function. Instead it uses addition, subtraction, multiplication and division, and the complexity of the equation is reduced, making the calculation easy and quick.     

Comparison of Two Fading Filters anc Adaptively Robust Filter

Two kinds of fading filters and their principles are introduced. An adaptive robust filter is given with corresponding principle. The basic abilities of the fading filters and adaptively robust filter in controlling the influences of the kinematic model errors are analyzed. A practical example is given. The results of the fading filter and adaptively robust filter are compared and analyzed.