The exact theory of inductive conductivity sensors for oceanographic application

The results of a general theoretical investigation of three commonly used types of inductive conductivity sensors, i.e., the single transformer, the double transformer, and the double transformer with an additional loop, are presented. The resulting formulas describe the dependence of the sensor output signal not only on the conductivity of the seawater but also on the parameters of the electrical circuit, among them the permeability of the transformer core(s), which-unlike the other parameters-shifts considerably during oceanographic in situ measurements. A mathematical discussion of these formulas shows that for certain circuit configurations, the sensor output is independent of changes in permeability. Most of these configurations form the basis of existing oceanographical conductivity sensors, among them the "classical" sensors developed by H. Hinkelmann [3], [4], and by N. L. Brown [14], while some others make evident further possibilities for eliminating the unwanted effects of shifting permeability. In the era of microelectronics, the latter might lead to a reassessment, especially of the single transformer-type sensor.     

Axial convergence in a well-mixed estuary

Transverse secondary circulations involving surface convergence, observed in a well-mixed estuary in North Wales, are made visible by the collection of surface material along an axial line which extends continuously for many kilometres through the estuary. The circulation and axial convergence, however, are seen only during the flood phase of the tide and no similar behaviour has been observed during the ebb phase.Convergent circulations in the estuary are associated with small but steady transverse density gradients in the cross-section, produced by non-uniform advection of the longitudinal gradient through the channel. A diagnostic model, using measured mean distributions of cross-sectional density, indicates surface transverse velocities (～0.1 ms^?1) similar to those observed in the estuary. The model further predicts appreciable transverse divergent currents at a fractional depth of 0.75: a prediction which has been tested in the estuary using a vertical array of accurately resolving current direction indicators.     

Reef exploration in the East Sengkang Basin,Sulawesi, Indonesia

Reconnaissance seismic shot in 1971/72 showed a number of well defined seismic anomalies within the East Sengkang Basin which were interpreted as buried reefs. Subsequent fieldwork revealed that Upper Miocene reefs outcropped along the southern margin of the basin. A drilling programme in 1975 and 1976 proved the presence of shallow, gas-bearing, Upper Miocene reefs in the northern part of the basin. Seismic acquisition and drilling during 1981 confirmed the economic significance of these discoveries, with four separate accumulations containing about 750 × 10⁹ cubic feet of dry gas in place at an average depth of 700 m. Kampung Baru is the largest field and contains over half the total, both reservoir quality and gas deliverability are excellent. Deposition in the East Sengkang Basin probably started during the Early Miocene. A sequence of Lower Miocene mudstones and limestones unconformably overlies acoustic basement which consists of Eocene volcanics. During the tectonically active Middle Miocene, deposition was interrupted by two periods of deformation and erosion. Carbonate deposition became established in the Late Miocene with widespread development of platform limestones throughout the East Sengkang Basin. Thick pinnacle reef complexes developed in the areas where reef growth could keep pace with the relative rise in sea level. Most reef growth ceased at the end of the Miocene and subsequent renewed clastic sedimentation covered the irregular limestone surface. Late Pliocene regression culminated in the Holocene with erosion. The Walanae fault zone, part of a major regional sinistral strike-slip system, separates the East and West Sengkang Basins. Both normal and reverse faulting are inferred from seismic data and post Late Pliocene reverse faulting is seen in outcrop.     

Microstructures of co-axially folded vein segments and crenulation cleavage： Evidence for dissolution phenomena in the Chamba Thrust Sheet, western Himalayas

The metasediments in the Chamba region experienced three phases of deformation: DF1, DF2 and DF3.Folded quartz veins are co-folded with the F2 crenulation folds. Their geometric and tectonic significance is studied by microstructures and shortening adjacent to the discrete crenulation cleavage, S2. Microstructures of folded vein segments, their geometric changes and truncation to cleavage (S2) are mainly due to pressure-solution phenomena and the estimated volume loss from reconstructed vein segments range from 16 to 25.5%,which is closely related to volume decrease (26%) calculated from the polydeformed slates of North Wales areas.     

Comparison of marine gas hydrates in sediments of an active and passive continental margin

Two sites of the Deep Sea Drilling Project in contrasting geologic settings provide a basis for comparison of the geochemical conditions associated with marine gas hydrates in continental margin sediments. Site 533 is located at 3191 m water depth on a spit-like extension of the continental rise on a passive margin in the Atlantic Ocean. Site 568, at 2031 m water depth, is in upper slope sediment of an active accretionary margin in the Pacific Ocean. Both sites are characterized by high rates of sedimentation, and the organic carbon contents of these sediments generally exceed 0.5%. Anomalous seismic reflections that transgress sedimentary structures and parallel the seafloor, suggested the presence of gas hydrates at both sites, and, during coring, small samples of gas hydrate were recovered at subbottom depths of 238m (Site 533) and 404 m (Site 568). The principal gaseous components of the gas hydrates wer methane, ethane, and CO₂. Residual methane in sediments at both sites usually exceeded 10 mll^?1 of wet sediment. Carbon isotopic compositions of methane, CO₂, and ΣCO₂ followed parallel trends with depth, suggesting that methane formed mainly as a result of biological reduction of oxidized carbon. Salinity of pore waters decreased with depth, a likely result of gas hydrate formation. These geochemical characteristics define some of the conditions associated with the occurrence of gas hydrates formed by in situ processes in continental margin sediments.     

A critical state model for sands dependent on stress and density

An elastoplastic model for sands is presented in this paper, which can describe stress–strain behaviour dependent on mean effective stress level and void ratio. The main features of the proposed model are: (a) a new state parameter, which is dependent on the initial void ratio and initial mean stress, is proposed and applied to the yield function in order to predict the plastic deformation for very loose sands; and (b) another new state parameter, which is used to determine the peak strength and describe the critical state behaviour of sands during shearing, is proposed in order to predict simply negative/positive dilatancy and the hardening/softening behaviour of medium or dense sands. In addition, the proposed model can also predict the stress–strain behaviour of sands under three-dimensional stress conditions by using a transformed stress tensor instead of ordinary stress tensor. Copyright © 2004 John Wiley & Sons, Ltd.     

Plane of elastic non-resisting tension material under foundation structures

In the frame of 2D-static problems one approaches the problem of elastic-NRT (not-resisting tension) semi-plane loaded on its limit line. This problem is intended to model the stress situation induced in the soil by a foundation structure. The solution, in terms of activated stress field, is searched for in the class of stress fields satisfying equilibrium and admissibility conditions, by applying an energy approach. Copyright © 2004 John Wiley & Sons, Ltd.