A simple model for lensing by black holes in galactic nuclei

The lensing properties of the Plummer model with a central point mass and external shear are derived, including the image multiplicities, critical curves and caustics. This provides a simple model for a flattened galaxy with a central supermassive black hole. For the Plummer model with black hole, the maximum number of images is four, provided the black hole mass is less than an upper bound which is calculated analytically. This introduces a method to constrain black hole masses by counting images, thus applicable at cosmological distance. With shear, the maximum number of images is six and we illustrate the occurrence of an astroid caustic and two metamorphoses.     

Deep-ocean piezometer probe technology for geotechnical investigations

Two single-sensor piezometer probes, 8 mm in diameter, were developed for deep-ocean geotechnical investigations. These probes were tested in a hyperbaric chamber pressurized to 55 MPa (8000 psi). Testing was performed for a period of five weeks under high hydrostatic pressure with the probes inserted in reconstituted illitic marine sediment. Small differential pore-water pressures were generated in response to both mechanically and thermally generated forcing functions. During deep-ocean simulated pressure tests, the sensors exhibited excellent sensitivity and stability. These developments in piezometer-probe technology provide a quantitative means of assessing important geotechnical parameters of fine-grained seabed deposits.     

Methods of array element localization for a towed underwateracoustic array

The location of the hydrophones on a towed underwater acoustic array as a function of time (array element localization) is needed for signal processing. Methods to perform this localization using least squares polynomial fitting to data from depth sensors, heading sensors, and sensors detecting a ping from a single source are discussed. Arc distance along the array is used as the independent parameter so that all solutions are constrained to be space curves. Examples of application to real data are presented, and techniques to discriminate against bad sensor data are discussed     

New developments in eclipsing binary light curve modeling

The light curve modeling of binary stars has continued to evolve since its founding by Henry Norris Russell (see Russell and Merrill 1952 and citations therein) nearly a century ago, accelerated in the 1950s by Kopal's introduction of Roche geometry into models and by the development of synthetic light curve computer code in the 1970's. Improved physics and the use of more kinds of observational input are providing another round of important advances that promise to enlarge our knowledge of both binary stars and ensembles containing them. Here we discuss the newer horizons of light curve modeling and the steps being taken toward them.     

Vertical stress distribution due to an arbitrarily shaped foundation using triangulation and an analytical expression for a triangular loaded region

Using the basic Boussinesq's equation, the expression for the vertical stress distribution (σ_z) underneath any point on the ground surface due to a general triangular loaded region in a preferred orientation with a linearly varied loading has been successfully derived. When the triangle is not in a preferred orientation, a simple axis transformation is required and the expression will be equally applicable. Based on this expression, σ_z due to an arbitrarily shaped loaded foundation can simply be determined by first triangulating the loaded area and summing up the contributions from each generated triangular region. The procedures for triangulating and calculating the stress distribution can be simply automated through computer programs.     

Observational Selection of Comet Discoveries

The distribution of perihelion distances of nearly periodic comets was studied using different assumptions about comet discovery probabilities. It was shown that the concentration of perihelia at small heliocentric distances cannot be explained solely by the influence of visibility conditions.     

The influence of a non‐associated flow rule on the calculation of the factor of safety of soil slopes

This paper presents a method that incorporates a non‐associated flow rule into the limit analysis to investigate the influence of the dilatancy angle on the factor of safety for the slope stability analysis. The proposed method retain's the advantage of the upper bound method, which is simple and has no stress involvement in the calculation of the energy dissipation and the factor of safety. Copyright © 2001 John Wiley & Sons, Ltd.     

Why Mt Etna?

The Etna volcano is located in an apparently anomalous position on the hinge zone of the Apennines subduction and its Na-alkaline geochemistry does not favour a magma source from the deep slab as indicated for the Aeolian K-alkaline magmatism. The steeper dip of the regional foreland monocline at the front of the Apennines in the Ionian Sea than in Sicily, implies a larger rollback of the subduction hinge in the Ionian Sea. Moreover, the lengthening of the Apennines arc needs extension parallel to the arc. Therefore, the larger southeastward subduction rollback of the Ionian lithosphere with respect to the Hyblean plateau in Sicily, should kinematically produce right-lateral transtension and a sort of vertical 'slab window' which might explain (i) the Plio-Pleistocene alkaline magmatism of eastern Sicily (e.g. the Etna volcano) and (ii) the late Pliocene to present right lateral transtensional tectonics and seismicity of eastern Sicily. The area of transfer of different dip and rollback occurs along the inherited Mesozoic passive continental margin between Sicily and the oceanic Ionian Sea, i.e. the Malta escarpment.